Genie 3064H manual Overview Remotes and Options, Hold, Press both, Simultaneously on

Page 15
Three Button
Remote

5 OVERVIEW - REMOTES AND OPTIONS

WARNING

A moving door can cause serious injury or death.

1.Keep people clear of opening while door is moving.

2.Do NOT allow children to play with opener, including wall console, remote, or wireless keypad.

3.During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle. See page 19 for Release Handle operation.

LOST OR STOLEN REMOTE - CLEARING MEMORY

Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad.

NOTE: Follow the PROGRAM REMOTE TO POWERHEAD steps to re-enter remaining or new remotes. See page 9.

 

 

 

PROGRAM

+

1. Press

PROGRAM

and hold

 

—

SET

 

SET

until both lights come ON BLUE. Release button.

FIG. 5-1 Remote

See page 21 for battery changing instructions.

PROGRAM

3.Press SET again and long LED flashes

PURPLE.

2.Lights go out and Round BLUE light comes ON.

PROGRAM

+

 

—

 

SET

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS

210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiver antenna.

•Increase the separation between the opener and receiver.

•Connect the opener into an outlet on a circuit different from that to which the receiver is connected.

•Consult your local dealer.

4.

Press both and

PROGRAM

+

 

 

 

 

simultaneously on the

 

—

 

 

 

powerhead and hold until both LEDs flash BLUE.

•Verify memory is cleared. Press a remote button that was previously programmed to the powerhead. Remote will not activate door opener.

•Garage door opener will operate normally using wall console.

•Program remaining or new remotes as shown on page 9. Your door opener will no longer recognize any signal received from the missing remote, or any other which has not been reprogrammed to the powerhead.

©2010 The Genie Company

12/2010

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operation and Maintenance Manual Prevention Potential HazardSafety Features Opener FeaturesTable of Contents Infrared Protection Function Important Installation InstructionsProgramming Limits & Force Both LEDs flash Blue Go OFF PressSee long Blue LED flashing Press and Hold until door is Fully Open then ReleaseTest AdjustmentSee both LEDs Flash Blue See both LEDs OFF Program Intellicode 2 Remote to PowerheadIntelliCode 1 remotes See round Blue LED come onSee long Purple LED flashing Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See oneReference Powerhead & Rail Assembled View Typical Sectional Door Installation Typical ONE Piece Door Installation Overview of Powerhead Controls On powerheadProgramming Buttons location Simultaneously on Overview Remotes and OptionsHold Press both2010 IntelliCode Intellicode FeaturesUse this New IntelliCode 2 openersTransmitter Compliance Statement Maintenance & TroubleshootingDoor Balance Spring Tension Routine Monthly MaintenanceAdjustment Safe-T-Beam System Check Door balance Contact reverseShuttle ENGAGE/DISENGAGE Disconnect power to door openerReset OPEN/CLOSE Travel Limit Change Light BulbsControls door opener lights from inside garage Wire routingWall Console Overview Open and closes door from inside garageThis area left blank Remote Battery ReplacementAdjustment Guide Speed Settings Change Speed SettingPowerhead LEDs Round LED Long LED Force Level LED indicator colors Adjustment Guide Force SettingsChange Force Setting Down Force settings within the available rangeTroubleshooting Guide Operation Powerhead LED Possible Problem Solution Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing coverTrilo

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.
Top Page Image Contents