Genie 3064H manual Programming Limits & Force

Page 6

6

©2010 The

1 PROGRAMMING LIMITS & FORCE

(Continuing from Installation Poster if provided)

SETTING & TESTING LIMITS AND FORCE

The OPEN (UP) and CLOSE (DOWN) Door Limit positions are controlled by making adjustments using the panel located on the bottom of the powerhead. Begin with Step 1 and continue through Step 10. Door Force is set during the final Open/Close cycle of these steps. The powerhead will automatically set door speed at slow if the distance between limits is less than 6 feet. Once Limits and Force are set DO NOT use the or buttons to open or close door.

FOR A LIMITS PROGRAMMING QUICK REFERENCE CARD VISIT WWW.GENIECOMPANY.COM

WARNING

• Make sure doorway is in view and clear of obstacles

and people to avoid injury or damage to property.

• DO NOT operate this unit from wall console before

LIMITS and FORCE are set. Severe damage to the

opener can occur.

• Shuttle MUST be engaged to carriage BEFORE setting

limits. See Installation Poster (if provided) or refer to

Genie

A) CLOSE DOOR TRAVEL LIMIT

pages 11 and 19.

Company

NOTE: If shuttle has NOT been engaged to the carriage, do so now.

Please note that there is a 30 second timeout between each programming step.

A programming timeout during these steps has occured when two RED flashing LEDs appear.

In the event of a timeout please restart at Step 1.

1PRESS and HOLD

PROGRAM

SET

—

+

 

 

 

 

 

SEE BOTH Blue LEDs come ON

2

RELEASE

SEE round

Blue LED come ON

3PRESS and RELEASE

PROGRAM

—

+

 

 

 

SEE long Blue

LED come ON

If RED LED comes ON - STOP and

exit programming.

3a

NOTE: If one or both LEDs come ON RED

12/2010

at this time, Limits programming menu

was not entered properly. You must exit

 

programming and restart.

 

To exit the programming function wait 30

 

seconds for the programming to time out.

 

 

4

PRESS and

PROGRAM

SET

—

 

 

 

RELEASE

 

 

 

SEE round Blue

LED flashing

5 PRESS and HOLD until door is FULLY CLOSED then RELEASE

RAM

 

 

 

 

 

 

 

 

 

 

 

 

G

SET

—

+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE

 

 

 

 

 

 

 

 

 

 

Watch door move

NOTE: You can start and stop door movement using either buttons until door is in correct open or closed position.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operation and Maintenance Manual Potential Hazard PreventionOpener Features Safety FeaturesTable of Contents Important Installation Instructions Infrared Protection FunctionProgramming Limits & Force Press and Hold until door is Fully Open then Release PressSee long Blue LED flashing Both LEDs flash Blue Go OFFAdjustment TestSee round Blue LED come on Program Intellicode 2 Remote to PowerheadIntelliCode 1 remotes See both LEDs Flash Blue See both LEDs OFFSee one Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See long Purple LED flashingReference Powerhead & Rail Assembled View Typical Sectional Door Installation Typical ONE Piece Door Installation Overview of Powerhead Controls On powerheadProgramming Buttons location Press both Overview Remotes and OptionsHold Simultaneously onNew IntelliCode 2 openers Intellicode FeaturesUse this 2010 IntelliCodeMaintenance & Troubleshooting Transmitter Compliance StatementSafe-T-Beam System Check Door balance Contact reverse Routine Monthly MaintenanceAdjustment Door Balance Spring TensionChange Light Bulbs Disconnect power to door openerReset OPEN/CLOSE Travel Limit Shuttle ENGAGE/DISENGAGEOpen and closes door from inside garage Wire routingWall Console Overview Controls door opener lights from inside garageRemote Battery Replacement This area left blankAdjustment Guide Speed Settings Change Speed SettingPowerhead LEDs Round LED Long LED Down Force settings within the available range Adjustment Guide Force SettingsChange Force Setting Force Level LED indicator colorsTroubleshooting Guide Operation Powerhead LED Possible Problem Solution Disconnect power from opener prior to removing cover Opening Cover May Cause Electric ShockTrilo

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.
Top Page Image Contents