Change Light Bulbs, Disconnect power to door opener

CHANGE LIGHT BULBS

WARNING

• Observe all safety warning and precautions!

Improper light bulb removal or replacement

could result in Death or Serious Injury.

• Disconnect power from opener before

beginning this task.

• When replacing light cover, make sure wires are

not pinched or near moving parts.

1. Disconnect power to door opener.

• Open powerhead light cover.

• Remove light bulb(s).

• Replace with maximum 100 Watt light bulb(s).

SHUTTLE ENGAGE/DISENGAGE

Use Release Handle to manually connect or release Shuttle from carriage and screw drive shaft.

TO RELEASE SHUTTLE:

1. Pull DOWN on handle and let go.

2. Raise or lower door manually.

NOTICE	DOOR
IFDOORBECOMESOBSTRUCTED
PULLDOWNONHANDLE

– Do NOT use light bulbs with greater than

TO ENGAGE SHUTTLE:

PULL

100 Watt rating.

• Close powerhead light cover.

2. Reconnect power to door opener.

• Test light operation.

MOTION DETECTOR* - OVERVIEW

(Not available on all models)

Powerheads equipped with a motion detector sensor provide additional security when

exiting or entering the garage area.

*This sensor works by detecting body heat. Range of detection may be reduced when the temperature in the garage is close to body temperature.

NOTE: Detector positioning on the powerhead provides for monitoring below the powerhead.

OPERATION

•Detector sensor is always ON. There are NO user controls or adjustments.

•Lights automatically turn ON when a change is detected and will turn OFF after 4 minutes of no change.

•Motion detector sensor will not turn OFF lighting turned ON at the wall console.

•Lighting turned ON at the wall console will remain ON until wall console turns lighting OFF or opener

is used.

Motion Detector

1.Pull DOWN on handle and let go.

2.Raise or lower door using remote or wall console.

FIG. 6-3 Shuttle Release

RESET - OPEN/CLOSE TRAVEL LIMIT

Performing all ten (10) Limits/Force setting steps (pages 6-7) erases previous Limits/Force settings.

NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed and Limits are programmed.

12/2010

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.