Genie 3064H manual Adjustment Guide Speed Settings, Change Speed Setting

Page 22

ADJUSTMENT GUIDE - SPEED SETTINGS

Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit.

However, travel speed for the opener in both the open and close directions can be adjusted to slower speeds to minimize normal wear for heavy sectional doors.

NOTE: One piece doors are automatically set during Limits programming to the slowest speed and opener speed cannot be reset for one piece doors.

FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

CHANGE SPEED SETTING

Use this guide to ADJUST powerhead SPEED settings.

There are three (3) Speed settings available on this unit for the open and close directions. Door type (one piece or sectional), door weight and balance, and condition of door components / track affect door speed. Speed adjustment may not be available for some installations depending on these factors.

PROGRAM

1.Press on the powerhead and hold until both

SET

lights turn steady ON. Release button.

Lights go out and Round BLUE light comes ON.

2.Press two times and the Round BLUE and Long BLUE lights come ON.

PROGRAM

3.Press once to enter the Speed Programming menu.SET The round LED will flash BLUE 3 times, then the current Speed setting for UP travel will display on the LEDs. See table below.

4.Press to raise or to lower UP Speed settings withinthe available range.

NOTE: Faster door speeds may not be available.

PROGRAM

5.Press SET to set UP Speed level. The long LED will flash BLUE 3 times, then the current Speed setting for DOWN travel will display on the LEDs.

6.Press to raise or to lower DOWN Speed settings within the available range.

NOTE: Faster door speeds may not be available.

PROGRAM

7.Press SET to set DOWN Speed level. Both LEDs flash BLUE to confirm.

Speed Level

Powerhead LEDs

Round LED Long LED

Default LED display is the current Speed setting

Red Red

LED Speed indicator colors

Purple

Purple

Blue Blue

Speed Level LED indicator colors

MAXIMUM

MID

SLOW

Red

Red

ON

ON

Purple

Purple

ON

ON

Blue

Blue

ON

ON

22

©2010 The Genie Company

12/2010

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operation and Maintenance Manual Potential Hazard PreventionOpener Features Safety FeaturesTable of Contents Important Installation Instructions Infrared Protection FunctionProgramming Limits & Force Press and Hold until door is Fully Open then Release PressSee long Blue LED flashing Both LEDs flash Blue Go OFFAdjustment TestSee round Blue LED come on Program Intellicode 2 Remote to PowerheadIntelliCode 1 remotes See both LEDs Flash Blue See both LEDs OFFSee one Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See long Purple LED flashingReference Powerhead & Rail Assembled View Typical Sectional Door Installation Typical ONE Piece Door Installation On powerhead Overview of Powerhead ControlsProgramming Buttons location Press both Overview Remotes and OptionsHold Simultaneously onNew IntelliCode 2 openers Intellicode FeaturesUse this 2010 IntelliCodeMaintenance & Troubleshooting Transmitter Compliance StatementSafe-T-Beam System Check Door balance Contact reverse Routine Monthly MaintenanceAdjustment Door Balance Spring TensionChange Light Bulbs Disconnect power to door openerReset OPEN/CLOSE Travel Limit Shuttle ENGAGE/DISENGAGEOpen and closes door from inside garage Wire routingWall Console Overview Controls door opener lights from inside garageRemote Battery Replacement This area left blankChange Speed Setting Adjustment Guide Speed SettingsPowerhead LEDs Round LED Long LED Down Force settings within the available range Adjustment Guide Force SettingsChange Force Setting Force Level LED indicator colorsTroubleshooting Guide Operation Powerhead LED Possible Problem Solution Disconnect power from opener prior to removing cover Opening Cover May Cause Electric ShockTrilo

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.
Top Page Image Contents