Installation Header and Door Mounting Brackets, Extend

2INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

HEADER AND DOOR

MOUNTING BRACKETS:

CAUTION

Header bracket must be fastened to garage framing. Do NOT fasten to drywall, particle board, plaster or other such materials.

1.Finding header bracket mounting location.

•Close garage door.

–Use a pencil and level.

a)Mark center of garage door (one-half overall width) on the wall with 6" vertical line at top edge of door.

b)Continue this line on wall above door for about 12" (Fig. 2-1, a).

•Raise garage door until top edge of door reaches its maximum height (Fig. 2-2).

•With door at highest point.

–Measure height from top edge of door to floor

(Fig. 2-2).

•Close door again.

•Mark height measurement on wall above door

(Fig. 2-1, c).

–Make your mark across vertical line made earlier.

•Add 2-1/2" to height mark just made on wall. This is location for header bracket (Fig. 2-1, d).

WARNING

Door springs are under high tension. If spring or its shaft is in the way, measure 2-1/2" above spring or shaft on the garage door centerline and mark this height as your location for header bracket.

Do NOT move door spring!

NOTE: If header bracket location needs to be above header for garage door opening, you need to add a "mounting surface." A 2" x 6" board securely attached (board and fasteners not included) to wall studs on either side of your mark is sufficient (Fig. 2-3).

NOTE: For header bracket and bolts locate Bag 2 from Box 1.

NOTE: The bolts supplied in Bag 2 are designed to be used on pressure treated lumber.

2.Mounting the header bracket.

•Hold header bracket against wall (Fig. 2-3).

•Position bracket as shown.

–Place center on vertical line.

–Bottom edge on final height line.

•Mark screw hole locations on wall.

•Drill 3/16" pilot holes at each screw hole mark.

–Fasten header bracket with 2 lag screws (provided) (Fig. 2-3).

b) - extend

vertical line

2-1/2"

		d) - final
c) - door at
		height mark
highest point

	top of door
	in closed
	in closed	a) - 6" vertical
		a) - 6" vertical
	position	line
		line


FIG. 2-1 Final height mark.

HIGHEST POINT OF TRAVEL

2-1/2"

HEADER

TRACK

SECTIONAL	HEADER
DOOR	HEADER	HIGHEST POINT OF TRAVEL
		TRACK
FROM HERE	SECTIONAL	FROM HERE
TO FLOOR	SECTIONAL	FROM HERE
TO FLOOR	DOOR	TO FLOOR
	DOOR	TO FLOOR

FIG. 2-2 Finding highest point of travel.

				final
final				height
final				mark
height	mark			mark
	mark
2-
1/2"
door at		highest		door at	highest	point
door at			point		highest

FIG. 2-3 Header bracket mounting (on header &

above header).

PN# 3642036212, 8/09/2007	11

1022, 1024 specifications

Genie 1024 is a cutting-edge generative AI model that has gained attention for its remarkable capabilities in producing coherent and contextually relevant text. As a significant advancement in natural language processing (NLP), Genie 1024 represents a leap forward in AI technology, allowing for more nuanced understanding and generation of human-like text.

One of the main features of Genie 1024 is its impressive size, denoted by its name. The model boasts 1024 parameters, enabling it to grasp a broad range of linguistic patterns and contextual relationships. This extensive parameter count allows Genie 1024 to generate text that is not only coherent but also stylistically varied, making it suitable for diverse applications, from creative writing to technical documentation.

The architecture of Genie 1024 is based on transformer technology, which has become the de facto standard in NLP due to its ability to handle large datasets and complex relationships in language. This model utilizes self-attention mechanisms, allowing it to weigh the importance of different words in a sentence relative to one another. This capability enhances the model's comprehension and allows it to produce context-aware responses.

Another standout characteristic of Genie 1024 is its training regimen, which incorporates extensive datasets from various domains, including literature, science, and social media. This diverse training corpus equips the model with a rich understanding of language nuances, idioms, and cultural references, thus enabling it to generate responses that resonate with users from different backgrounds.

In terms of usability, Genie 1024 is designed with user-friendliness in mind. Developers and businesses can easily integrate the model into their applications through user-friendly APIs or dedicated platforms. This accessibility paves the way for innovative applications across industry sectors, enhancing customer engagement and automating content creation processes.

Moreover, Genie 1024 places a significant emphasis on ethical and responsible AI use. The team behind the model has implemented guidelines for bias mitigation, promoting fairness and inclusivity in its responses. Users can benefit from comprehensive usage guidelines and support resources that encourage effective deployment while navigating potential challenges.

In summary, Genie 1024 stands out as a remarkable generative AI model that combines advanced transformer architecture, extensive parameters, and diverse training data. With a focus on both functionality and ethical considerations, it opens up new horizons for applications in natural language processing, benefiting both developers and end-users alike.