Genie 1024 Carriage Lock, UP/DOWN Force, Erase OPEN/CLOSE Travel Limit, Contact Reverse Test

Page 20

CARRIAGE LOCK

The Carriage Lock can be manually engaged or disengaged.

To disengage Carriage Lock

Pull handle towards opener.

To engage Carriage Lock

Pull handle towards door.

UP/DOWN FORCE

1.By turning the Down Force Control CLOSE clockwise,

the DOWN force can be increased. By turning the Down Force Control CLOSEcounter-clockwise, the DOWN force can be decreased. Set the DOWN force level at the minimum force required to close door without reversing.

2.Once the desired level is selected, this stores the maximum force level for the DOWN direction in memory.

OPEN

3.By turning the Up Force Control clockwise, the

UP force can be increased. By turning the Up Force

OPEN

Control counter-clockwise, the UP force can be decreased. Set the UP force level at the minimum force required to open door without stopping.

4.Once the desired level is selected, this stores the maximum force level for the UP direction in memory.

ERASE - OPEN/CLOSE TRAVEL LIMIT

1.Press and hold both of the "SET" buttons ( SET & SET ) together until the green indicator light blinks (about 5 seconds).

2.All close and open travel limit settings are erased. Then follow the steps above to reprogram close and open travel limits.

NOTE: The operator will not close the door automatically unless the Safety Beam System is installed.

CONTACT REVERSE TEST

The force adjustments and limit switch settings MUST BE COMPLETED before testing.

1.Testing.

Open garage door using wall control.

Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-5).

Close door using wall control.

When door contacts board, it must stop and reverse (within 2 seconds) to open position.

2.Adjustment.

If the door does not properly reverse.

Check to see if door has "close" limit programmed. It should not have reached its "close" limit before hitting board.

If the door STOPS but does not reverse, decrease "CLOSE FORCE" control CLOSE setting slightly (turn it counter-clockwise).

Test again. Repeat as necessary.

DOOR

 

UNLOCK

LOCK

TO RELEASE

TO RECONNECT

PULL TOWARD

PULL TOWARD

THE OPENER

DOOR

FIG. 6-3 Engage/Disengage Carriage Lock.

Up Force

OPEN Control

Adjustment

FORCE

ROTATE

CLOCKWISE

 

ROTATE

 

COUNTER-CLOCKWISE

CLOSE Down Force

Control

Adjustment

FIG. 6-4 Force Control Adjustment.

FIG. 6-5 2 x 4 under center of door opening.

20

PN# 3642036212, 8/09/2007

 

Image 20
Contents Model 1022/1024 Safety Information Moving DoorElectrical Shock High Spring TensionSafety Features Table of ContentsOperator Features Section Do not USE Alternate Power SuppliesDo not USE AN Extension Cord MAX MIN Typical Sectional Door InstallationApprox Recommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Piece Rail Hardware Assembled View Chain tensionerOperator Assembly Box Label Example Internal boxesSplit Rail assembly Split Rail sectionsInstallation Header and Door Mounting Brackets Finding header bracket mounting locationDo not move door spring Mounting the header bracket ExtendMounting the assembly Mounting the OperatorAngle Iron on Finished Ceiling Unfinished or Open BeamInstall Door Arms Door BracketWall Control Installation 2a. Wiring If pre-wired2b. Wiring If not pre-wired Wall Control locationSecurely fasten wires Do not install rear cover yetPower Head With Rear Cover Removed -3 Insert wires MountingAs you go -6 on next Mounting Safety Beam Source Red LED and Sensor Green LED3a. Wiring If not pre-wired 3b. Wiring pre-wired Route wire from ceiling to power headDo not install the white lamp cover at this time Power Head With Rear Cover Not Shown Cover clipsConnecting to Power With Permanent WiringWith Power Supplied With Grounded PlugLimit Controls location on power head Door LimitsEngage Chain to Carriage Close Travel LimitCarriage Lock UP/DOWN ForceErase OPEN/CLOSE Travel Limit Contact Reverse TestProgramming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Battery replacementVisor clip Light bulbMaintenance Routine Monthly MaintenanceSafety Beam System Door balancePower Cord Circuit Wiring DiagramTroubleshooting Guide Operation Troubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement Limited Warranty For Answers Call
Related manuals
Manual 1 pages 40.03 Kb

1022, 1024 specifications

Genie 1024 is a cutting-edge generative AI model that has gained attention for its remarkable capabilities in producing coherent and contextually relevant text. As a significant advancement in natural language processing (NLP), Genie 1024 represents a leap forward in AI technology, allowing for more nuanced understanding and generation of human-like text.

One of the main features of Genie 1024 is its impressive size, denoted by its name. The model boasts 1024 parameters, enabling it to grasp a broad range of linguistic patterns and contextual relationships. This extensive parameter count allows Genie 1024 to generate text that is not only coherent but also stylistically varied, making it suitable for diverse applications, from creative writing to technical documentation.

The architecture of Genie 1024 is based on transformer technology, which has become the de facto standard in NLP due to its ability to handle large datasets and complex relationships in language. This model utilizes self-attention mechanisms, allowing it to weigh the importance of different words in a sentence relative to one another. This capability enhances the model's comprehension and allows it to produce context-aware responses.

Another standout characteristic of Genie 1024 is its training regimen, which incorporates extensive datasets from various domains, including literature, science, and social media. This diverse training corpus equips the model with a rich understanding of language nuances, idioms, and cultural references, thus enabling it to generate responses that resonate with users from different backgrounds.

In terms of usability, Genie 1024 is designed with user-friendliness in mind. Developers and businesses can easily integrate the model into their applications through user-friendly APIs or dedicated platforms. This accessibility paves the way for innovative applications across industry sectors, enhancing customer engagement and automating content creation processes.

Moreover, Genie 1024 places a significant emphasis on ethical and responsible AI use. The team behind the model has implemented guidelines for bias mitigation, promoting fairness and inclusivity in its responses. Users can benefit from comprehensive usage guidelines and support resources that encourage effective deployment while navigating potential challenges.

In summary, Genie 1024 stands out as a remarkable generative AI model that combines advanced transformer architecture, extensive parameters, and diverse training data. With a focus on both functionality and ethical considerations, it opens up new horizons for applications in natural language processing, benefiting both developers and end-users alike.