Genie Programming Garage Door Opener Remotes - Models 1022 and 1024

Page 21

7PROGRAMMING REMOTE CONTROLS

WARNING

A moving door can cause serious injury or death.

1.Keep people clear of opening while door is moving.

2.Do NOT allow children to play with Wireless Keypad.

3.During programming, the door opener could begin to run, so stay away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release.

NOTE: For remote control locate Box 3.

1a. Single Button Remote Programming.

NOTE: This operator can learn up to 7 single button remote controls.

Locate learn code button and indicator LED on the power head (next to force adjustment screws) (Fig. 7-1).

Press and release learn code button.

Indicator LED will blink RED at a rate of twice per second.

Within 30 seconds, push remote control button once.

Indicator LED will stop blinking and stay on.

Press remote control button again.

Red LED will go out. Remote is now programmed.

1b. Multi Button Remote Programming.

NOTE: Each button on a multi-button remote is designed for use with 1 door. You cannot program 2 buttons to operate the same door, nor can you program 1 button to operate 2 doors. You can program a maximum of 7 different transmitters or wireless devices.

NOTE: Pushing two buttons simultaneously will erase programmed memory and limits must be reset.

For each button.

Program each button separately using the Single Button Remote Programming steps.

2.Operating.

Press remote button once.

Door will move.

Press button again.

Door will stop.

Press button again.

Door will move in opposite direction.

NOTE: The door will stop automatically at the fully open or fully closed position.

LOST OR STOLEN REMOTE

1.Clear memory.

Press and hold learn code button (on power head) for 10 seconds or until the red blinking indicator LED goes out.

Program remaining or new remote controls as done previously. Your door operator will no longer recognize any signal received from the missing remote control, or any other which has not been reprogrammed.

NOTE: To program a

Homelink® and Car2U™

device follow the Homelink® or Car2U™ instructions in your car owner’s manual.

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiver antenna.

Increase the separation between the operator and receiver.

Connect the operator into an outlet on a circuit different from that to which the receiver is connected.

Consult your local dealer.

Limit controls location on power head.

LED

Open

Open

 

 

Indicator Light

Set Limit

 

Up Force

Travel Limit

 

 

 

Button

OPEN Control

 

 

 

 

 

 

 

 

Adjustment

To

 

 

SET

 

 

Garage Door

 

 

 

 

 

 

 

 

 

 

LEARN MANUAL LIMIT

FORCE

 

 

 

 

SET

 

 

Learn

 

 

 

 

 

Code

CODE

Close

Close

CLOSE

Down Force

Button

 

 

 

 

 

Travel Limit Set Limit

 

Control

 

 

 

Button

 

Adjustment

FIG. 7-1 Learn code button and LED

PN# 3642036212, 8/09/2007

21

 

Image 21
Contents Model 1022/1024 Moving Door Safety InformationElectrical Shock High Spring TensionTable of Contents Operator FeaturesSafety Features Do not USE Alternate Power Supplies Do not USE AN Extension CordSection Typical Sectional Door Installation ApproxMAX MIN Parts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Chain tensioner Piece Rail Hardware Assembled ViewBox Label Example Internal boxes Operator AssemblySplit Rail sections Split Rail assemblyFinding header bracket mounting location Installation Header and Door Mounting BracketsDo not move door spring Mounting the header bracket ExtendMounting the Operator Mounting the assemblyAngle Iron on Finished Ceiling Unfinished or Open BeamDoor Bracket Install Door Arms2a. Wiring If pre-wired Wall Control Installation2b. Wiring If not pre-wired Wall Control locationDo not install rear cover yet Securely fasten wiresPower Head With Rear Cover Removed -3 Insert wires MountingMounting Safety Beam Source Red LED and Sensor Green LED 3a. Wiring If not pre-wiredAs you go -6 on next Route wire from ceiling to power head 3b. Wiring pre-wiredDo not install the white lamp cover at this time Power Head With Rear Cover Not Shown Cover clipsWith Permanent Wiring Connecting to PowerWith Power Supplied With Grounded PlugDoor Limits Limit Controls location on power headEngage Chain to Carriage Close Travel LimitUP/DOWN Force Carriage LockErase OPEN/CLOSE Travel Limit Contact Reverse TestLost or Stolen Remote Programming Remote ControlsBattery replacement Light BULB/LENS InstallationVisor clip Light bulbRoutine Monthly Maintenance MaintenanceSafety Beam System Door balanceCircuit Wiring Diagram Power CordTroubleshooting Guide Operation Possible Problem Solution Troubleshooting Guide Power Head LEDTransmitter Compliance Statement For Answers Call Limited Warranty
Related manuals
Manual 1 pages 40.03 Kb

1022, 1024 specifications

Genie 1024 is a cutting-edge generative AI model that has gained attention for its remarkable capabilities in producing coherent and contextually relevant text. As a significant advancement in natural language processing (NLP), Genie 1024 represents a leap forward in AI technology, allowing for more nuanced understanding and generation of human-like text.

One of the main features of Genie 1024 is its impressive size, denoted by its name. The model boasts 1024 parameters, enabling it to grasp a broad range of linguistic patterns and contextual relationships. This extensive parameter count allows Genie 1024 to generate text that is not only coherent but also stylistically varied, making it suitable for diverse applications, from creative writing to technical documentation.

The architecture of Genie 1024 is based on transformer technology, which has become the de facto standard in NLP due to its ability to handle large datasets and complex relationships in language. This model utilizes self-attention mechanisms, allowing it to weigh the importance of different words in a sentence relative to one another. This capability enhances the model's comprehension and allows it to produce context-aware responses.

Another standout characteristic of Genie 1024 is its training regimen, which incorporates extensive datasets from various domains, including literature, science, and social media. This diverse training corpus equips the model with a rich understanding of language nuances, idioms, and cultural references, thus enabling it to generate responses that resonate with users from different backgrounds.

In terms of usability, Genie 1024 is designed with user-friendliness in mind. Developers and businesses can easily integrate the model into their applications through user-friendly APIs or dedicated platforms. This accessibility paves the way for innovative applications across industry sectors, enhancing customer engagement and automating content creation processes.

Moreover, Genie 1024 places a significant emphasis on ethical and responsible AI use. The team behind the model has implemented guidelines for bias mitigation, promoting fairness and inclusivity in its responses. Users can benefit from comprehensive usage guidelines and support resources that encourage effective deployment while navigating potential challenges.

In summary, Genie 1024 stands out as a remarkable generative AI model that combines advanced transformer architecture, extensive parameters, and diverse training data. With a focus on both functionality and ethical considerations, it opens up new horizons for applications in natural language processing, benefiting both developers and end-users alike.