Genie 1024, 1022 manual Recommended Tools, Parts Identification Not Shown Full Size

Page 6

RECOMMENDED TOOLS

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

3/16" Drill Bit

Pencil

Carpenter’s level

 

Drill

Wire strippers

Adjustable wrench

Ratchet

Tape measure

Step ladder

Safety Glasses

1/4", 7/16", 3/8" and

Phillips screwdrivers

Hammer

1/2" Sockets

 

 

 

PARTS IDENTIFICATION - Not Shown Full Size .

Safety Brochures

ARRANGING BOX CONTENTS FOR ASSEMBLY

ORGANISATION DU CONTENU DE LA BOÎTE POUR LE MONTAGE DISPOSICIÓN DEL CONTENIDO DE LA BOLSA PARA EL MONTAJE

Remove internal boxes.

Enlever les boîtes internes.

Quite las cajas internas.

Remove lens Box and motor power head.

Enlever la boîte des lentilles et la tête motorisée.

Quite la caja de la lente y el motor de la caja de control.

Carefully remove third rail (with chain

attached) and place on floor.

Enlever soigneusement le troisième rail (avec la

chaîne attachée) et le placer sur le sol.

Cuidadosamente quite el tercer riel (con la

cadena acoplada) y ponga en el piso.

Arrange three small boxes for easy access.

Arranger les trois petites boîtes de manière à pou-

voir y accéder facilement.

Disponga las tres cajas pequeñas para tener acceso

fácil.

Remove rail sections not connected

to chain.

Enlever les sections de rail non connectées

à la chaîne.

Quite las secciones de riel no conectadas a

la cadena.

Arrange rails in line and pull plastic sleeve off chain.

Arranger les rails en ligne et tirer sur le manchon en plastique

pour le dégager de la chaîne.

Disponga los rieles en línea y estire la camisa de plástico fuera

de la cadena.

Follow instructions in the Installation Manual for assembly steps.

Procéder selon les instructions stipulées dans le manuel d'installation pour les étapes de

montage à suivre.

Si l i t

i

l M

l d i t l ió

l

d

t j

Box Contents Sheet

Child can be pinned under automatic garage door. Death or serious injury can result.

Never let child walk or run under moving door. .

Never let child use door opener controls.

Always keep moving door in sight.

If person is pinned, push control button or use emergency release.

Test door opener monthly:

Refer to your’ owner' s manual.

Place 11/2-inch object (or 2x4 laid flat) on floor.

If door fails to reverse on contact, adjust opener.

If opener still fails to reverse door, repair or replace opener.

Do not remove or paint over this label.

Mount wall control out of child's reach (at least 5 feet above floor).

Place next to wall control.

©1999

Entrapment Warning

Label

 

Wire

Insulated Staple

Header Bracket

 

 

 

Safety Beam Source

Safety Beam Sensor

 

Door

with wire

 

Bracket

(Red LED)

with wire

 

 

 

(Green LED)

 

 

Rail Section Clamp

Head Rail Section

Safety Beam

Source/Sensor Bracket

Center Rail Section

Wall Control Button

End Rail Section

Door Arm

Three-button

Remote Control

6

PN# 3642036212, 8/09/2007

 

Image 6
Contents Model 1022/1024 Electrical Shock Safety InformationMoving Door High Spring TensionTable of Contents Operator FeaturesSafety Features Do not USE Alternate Power Supplies Do not USE AN Extension CordSection Typical Sectional Door Installation ApproxMAX MIN Recommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Piece Rail Hardware Assembled View Chain tensionerOperator Assembly Box Label Example Internal boxesSplit Rail assembly Split Rail sectionsDo not move door spring Mounting the header bracket Installation Header and Door Mounting BracketsFinding header bracket mounting location ExtendAngle Iron on Finished Ceiling Mounting the assemblyMounting the Operator Unfinished or Open BeamInstall Door Arms Door Bracket2b. Wiring If not pre-wired Wall Control Installation2a. Wiring If pre-wired Wall Control locationPower Head With Rear Cover Removed -3 Insert wires Securely fasten wiresDo not install rear cover yet MountingMounting Safety Beam Source Red LED and Sensor Green LED 3a. Wiring If not pre-wiredAs you go -6 on next Do not install the white lamp cover at this time 3b. Wiring pre-wiredRoute wire from ceiling to power head Power Head With Rear Cover Not Shown Cover clipsWith Power Supplied Connecting to PowerWith Permanent Wiring With Grounded PlugEngage Chain to Carriage Limit Controls location on power headDoor Limits Close Travel LimitErase OPEN/CLOSE Travel Limit Carriage LockUP/DOWN Force Contact Reverse TestProgramming Remote Controls Lost or Stolen RemoteVisor clip Light BULB/LENS InstallationBattery replacement Light bulbSafety Beam System MaintenanceRoutine Monthly Maintenance Door balancePower Cord Circuit Wiring DiagramTroubleshooting Guide Operation Troubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement Limited Warranty For Answers Call
Related manuals
Manual 1 pages 40.03 Kb

1022, 1024 specifications

Genie 1024 is a cutting-edge generative AI model that has gained attention for its remarkable capabilities in producing coherent and contextually relevant text. As a significant advancement in natural language processing (NLP), Genie 1024 represents a leap forward in AI technology, allowing for more nuanced understanding and generation of human-like text.

One of the main features of Genie 1024 is its impressive size, denoted by its name. The model boasts 1024 parameters, enabling it to grasp a broad range of linguistic patterns and contextual relationships. This extensive parameter count allows Genie 1024 to generate text that is not only coherent but also stylistically varied, making it suitable for diverse applications, from creative writing to technical documentation.

The architecture of Genie 1024 is based on transformer technology, which has become the de facto standard in NLP due to its ability to handle large datasets and complex relationships in language. This model utilizes self-attention mechanisms, allowing it to weigh the importance of different words in a sentence relative to one another. This capability enhances the model's comprehension and allows it to produce context-aware responses.

Another standout characteristic of Genie 1024 is its training regimen, which incorporates extensive datasets from various domains, including literature, science, and social media. This diverse training corpus equips the model with a rich understanding of language nuances, idioms, and cultural references, thus enabling it to generate responses that resonate with users from different backgrounds.

In terms of usability, Genie 1024 is designed with user-friendliness in mind. Developers and businesses can easily integrate the model into their applications through user-friendly APIs or dedicated platforms. This accessibility paves the way for innovative applications across industry sectors, enhancing customer engagement and automating content creation processes.

Moreover, Genie 1024 places a significant emphasis on ethical and responsible AI use. The team behind the model has implemented guidelines for bias mitigation, promoting fairness and inclusivity in its responses. Users can benefit from comprehensive usage guidelines and support resources that encourage effective deployment while navigating potential challenges.

In summary, Genie 1024 stands out as a remarkable generative AI model that combines advanced transformer architecture, extensive parameters, and diverse training data. With a focus on both functionality and ethical considerations, it opens up new horizons for applications in natural language processing, benefiting both developers and end-users alike.