Genie 1022, 1024 manual Operator Assembly, Box Label Example Internal boxes

Page 9

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING: Toreduce the risk of severe injury or death:

1.READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. (If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie Dealer.)

2.Install only on a properly balanced sectional garage door. An improperly balanced door could cause severe injury. Have a professionally trained service technician make repairs to cables, spring assemblies, and other hardware before installing the opener.

3.Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener.

4.Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release 6 feet above the floor.

5.Do NOT connect the operator to source of power until instructed to do so.

6.Locate the control button:

Within sight of door,

At minimum height of 5 feet so small children are not able to reach it, and

Away from all moving parts of the door.

7.Install the Entrapment WARNING Label next to the control button in a prominent location. Install the Emergency Release Marking on or next to the emergency release.

8.After installing the opener, the door must reverse when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor.

1OPERATOR ASSEMBLY

RAIL ASSEMBLY: Use a clean, flat surface.

WARNING

To reduce the risk of injury to persons or damage to property - Use this operator only with sectional doors.

CAUTION

Do NOT run until operator is fully assembled.

NOTE: Three (3) piece rail assemblies are for a 7 foot high door.

Clear a workspace area to unpack and organize box and contents for assembly.

1.There are 4 boxes inside the carton. Each box is numbered 1 - 4. Note that some operators will contain the same parts and be packaged with fewer boxes. Carefully remove the three internal boxes (Labeled #1, 2, and 3) and place them on the floor for easy access. (Fig. 1-1).These boxes contain assembly parts and the contents are organized by assembly tasks. For quick reference inside the lid of each box there is a label illustrating the components inside.

2.Remove the motor power head and place it on the floor for later use. Remove box #4 and place it on the floor for later use.

NOTE: For 1-piece rail—skip to POWER HEAD & RAIL ASSEMBLY on the next page.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

 

 

 

#4

Bag 0

Rail Connectors

Bag 2

Header Bracket

 

 

 

Rail Connector Bolts

 

 

 

 

Header Bracket

 

 

 

Bolts

 

 

Rail Connector Nuts

 

 

 

 

 

Lag Srews

Bag 1

Bolts

Bag 3

 

Rail

 

 

 

Mounting

 

 

 

Straps

 

 

 

5/16" Nuts

 

 

 

& Bolts

 

 

Power head

 

 

 

Box Label Example

 

FIG. 1-1

Internal boxes.

 

 

PN# 3642036212, 8/09/2007

9

 

Image 9
Contents Model 1022/1024 Moving Door Safety InformationElectrical Shock High Spring TensionTable of Contents Operator FeaturesSafety Features Do not USE Alternate Power Supplies Do not USE AN Extension CordSection Typical Sectional Door Installation ApproxMAX MIN Parts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Chain tensioner Piece Rail Hardware Assembled ViewBox Label Example Internal boxes Operator AssemblySplit Rail sections Split Rail assemblyFinding header bracket mounting location Installation Header and Door Mounting BracketsDo not move door spring Mounting the header bracket ExtendMounting the Operator Mounting the assemblyAngle Iron on Finished Ceiling Unfinished or Open BeamDoor Bracket Install Door Arms2a. Wiring If pre-wired Wall Control Installation2b. Wiring If not pre-wired Wall Control locationDo not install rear cover yet Securely fasten wiresPower Head With Rear Cover Removed -3 Insert wires MountingMounting Safety Beam Source Red LED and Sensor Green LED 3a. Wiring If not pre-wiredAs you go -6 on next Route wire from ceiling to power head 3b. Wiring pre-wiredDo not install the white lamp cover at this time Power Head With Rear Cover Not Shown Cover clipsWith Permanent Wiring Connecting to PowerWith Power Supplied With Grounded PlugDoor Limits Limit Controls location on power headEngage Chain to Carriage Close Travel LimitUP/DOWN Force Carriage LockErase OPEN/CLOSE Travel Limit Contact Reverse TestLost or Stolen Remote Programming Remote ControlsBattery replacement Light BULB/LENS InstallationVisor clip Light bulbRoutine Monthly Maintenance MaintenanceSafety Beam System Door balanceCircuit Wiring Diagram Power CordTroubleshooting Guide Operation Possible Problem Solution Troubleshooting Guide Power Head LEDTransmitter Compliance Statement For Answers Call Limited Warranty
Related manuals
Manual 1 pages 40.03 Kb

1022, 1024 specifications

Genie 1024 is a cutting-edge generative AI model that has gained attention for its remarkable capabilities in producing coherent and contextually relevant text. As a significant advancement in natural language processing (NLP), Genie 1024 represents a leap forward in AI technology, allowing for more nuanced understanding and generation of human-like text.

One of the main features of Genie 1024 is its impressive size, denoted by its name. The model boasts 1024 parameters, enabling it to grasp a broad range of linguistic patterns and contextual relationships. This extensive parameter count allows Genie 1024 to generate text that is not only coherent but also stylistically varied, making it suitable for diverse applications, from creative writing to technical documentation.

The architecture of Genie 1024 is based on transformer technology, which has become the de facto standard in NLP due to its ability to handle large datasets and complex relationships in language. This model utilizes self-attention mechanisms, allowing it to weigh the importance of different words in a sentence relative to one another. This capability enhances the model's comprehension and allows it to produce context-aware responses.

Another standout characteristic of Genie 1024 is its training regimen, which incorporates extensive datasets from various domains, including literature, science, and social media. This diverse training corpus equips the model with a rich understanding of language nuances, idioms, and cultural references, thus enabling it to generate responses that resonate with users from different backgrounds.

In terms of usability, Genie 1024 is designed with user-friendliness in mind. Developers and businesses can easily integrate the model into their applications through user-friendly APIs or dedicated platforms. This accessibility paves the way for innovative applications across industry sectors, enhancing customer engagement and automating content creation processes.

Moreover, Genie 1024 places a significant emphasis on ethical and responsible AI use. The team behind the model has implemented guidelines for bias mitigation, promoting fairness and inclusivity in its responses. Users can benefit from comprehensive usage guidelines and support resources that encourage effective deployment while navigating potential challenges.

In summary, Genie 1024 stands out as a remarkable generative AI model that combines advanced transformer architecture, extensive parameters, and diverse training data. With a focus on both functionality and ethical considerations, it opens up new horizons for applications in natural language processing, benefiting both developers and end-users alike.