Hitachi 236464 manual Technical Data, Tested in accordance with ISO

Page 25

Technical Data

WARNING

Be sure that all fluids and solvents used are chemically compatible with the Wetted Parts listed below. Always read the manufacturer’s literature before using fluid or solvent in this pump.

Category

Data

 

 

Maximum fluid working pressure

28.3 MPa, 283 bar (4100 psi)

 

 

Maximum air input pressure

0.7 MPa, 7 bar (100 psi)

 

 

Ratio

41:1

 

 

Pump cycles per 3.8 liters

26

(1 gallon)

 

 

 

Fluid flow at 60 cycles per minute

8.7 liters/min (2.3 gpm)

 

 

Air motor piston effective area

248 cm@ (38 in.@)

 

 

Stroke length

120 mm (4.75 in.)

 

 

Displacement pump effective

6 cm@ (0.93 in.@)

area

 

 

 

Maximum operating temperature

82_C (180_F)

 

 

Air inlet size

3/4 npsm(f)

Fluid inlet size

1–1/2” npt(f)

 

 

Fluid outlet size

3/4 npt(f)

 

 

Pump weight

approx. 39 kg (86 lb)

 

 

Displacement pump weight

approx. 13 kg (29 lb)

 

 

Wetted parts

304, 440 and 17–4 PH Grades of Stainless Steel; Tungsten Carbide; PTFE; r

 

Leather

 

 

Teflonr is a registered trademark of the DuPont Co.

Sound Pressure Levels (dBa) (measured at 1 meter from unit)

 

 

Input Air Pressures at 15 cycles per minute

 

 

 

 

 

 

 

0.28 MPa, 2.8 bar

0.48 MPa, 4.8 bar

0.63 MPa, 6.3 bar

0.7 MPa, 7 bar

Air Motor

(40 psi)

(70 psi)

(90 psi)

(100 psi)

 

 

 

 

 

Bulldog

82.4 dB(A)

87.3 dB(A)

88.5 dB(A)

90.0 dB(A)

 

 

 

 

 

Reduced Icing Quiet Bulldog

81.5 dB(A)

83.6 dB(A)

85.6 dB(A)

85.8 dB(A)

 

 

 

 

 

Sound Power Levels (dBa)

(tested in accordance with ISO 9614–2)

 

 

Input Air Pressures at 15 cycles per minute

 

 

 

 

 

 

 

0.28 MPa, 2.8 bar

0.48 MPa, 4.8 bar

0.63 MPa, 6.3 bar

0.7 MPa, 7 bar

Air Motor

(40 psi)

(70 psi)

(90 psi)

(100 psi)

 

 

 

 

 

Bulldog

91.6 dB(A)

95.9 dB(A)

97.4 dB(A)

98.1 dB(A)

 

 

 

 

 

Reduced Icing Quiet Bulldog

90.2 dB(A)

93.5 dB(A)

94.9 dB(A)

93.3 dB(A)

 

 

 

 

 

308350 25

Image 25 Contents
Dura-Flot600 Pumps Instructions Parts ListList of Models Table of ContentsEquipment Misuse Hazard SymbolsMoving Parts Hazard Injection HazardToxic Fluid Hazard Fire and Explosion Hazard308350 System Accessories InstallationGeneral Information Grounding Object being sprayed follow your local codeAir Line Accessories KEY Typical InstallationPressure Relief Procedure Operation/MaintenancePacking Nut/Wet-Cup 110Flush the Pump Before First Use Starting and Adjusting the PumpFlushing Shutdown and Care of the PumpIts stroke keep the wet-cup 1/3 filled with a Troubleshooting ChartCompatible solvent Disconnecting the Displacement Pump ServiceReconnecting the Displacement Pump Required Tools107 106 110 109 101 105 108Disassembly Displacement Pump ServiceTorque to 258-285 NSm 190-210 ft-lb Reassembly 10 Ref 11 Ref Housing 7 onto the cylinder handtight. Install the seal 11* on the bottomSealing surface of the intake housing Using a pipe wrench, torque the intake housing 101 105 108 109 102Y 107 106 110 Parts 102Y 107 106 110 101 105 108 109 Part No Pump, Series a 251 Ratio, with Senator Air Motor102Y 107 110 106 112 113Piston Packing Stack See Throat Packing Stack seeTeflonr Packing Kit 237236 Optional Packing KitsUHMWPE/Leather Packing Kit 237238 Optional UHMWPE/PTFErPacking Kit 237609 OptionalTested in accordance with ISO Technical DataLiters/min 11.4 Mounting Hole Layout DimensionsGraco Information Graco Standard Warranty