Review this table to find
WARNING
Disconnect electrical supply before performing maintenance to the unit. Failure to do so could result in electrical shock or personal injury.
All Surface | Floor | t. | Power cord not firmly plugged | 1. | Plugunit in firmly. |
|
|
| |||||||
Cleaner | won't |
| into outlet. |
|
|
|
|
|
|
|
|
| |||
run |
|
|
| 2. | Blown fuse or tripped breaker. | 2. | Check fuse or breaker in home. Replace | ||||||||
|
|
|
| 3. |
|
|
|
|
| fuse/reset | breaker. |
|
|
| |
|
|
|
| Brush clogged. |
| 3. | Unplug unit. Remove debris from brushro]l | ||||||||
|
|
|
| 4. |
|
|
|
|
| and push brushron | reset button. | ||||
|
|
|
| Thermal | Protector activated. | 4. | Unplug All Surface | Floor Cleaner. Allow to | |||||||
|
|
|
|
|
|
|
|
|
| cool for 30 minutes before use. | |||||
|
|
|
| 5. | Needs service. |
| 5. | Take to Sears Service Center. |
| ||||||
All Surface | Floor | 1. | Incorrectly | assembled. |
| 1. | Reassemble | All Surface | Floor Cleaner. | ||||||
Cleaner | won't | 2. | Clean/Dirty | Water Tank | not | 2, | Secure tank - Pg. 13 |
|
| ||||||
pick | up or | low |
| installed | properly. |
|
|
|
|
|
|
|
| ||
suction |
|
| 3. | Dirty water | tank is full. |
| 3. | Empty Dirty Water | Tank- | Pg. | 13 | ||||
|
|
|
| 4. | Nozzle clogged |
| 4. | Clean nozzle | opening. |
|
| ||||
|
|
|
| 5. | Filter clogged or dirty. |
| 5. | Remove | filter and clean | - Pg. | 14 | ||||
|
|
|
| 6. | Incorrect | nozzle attached. | 6. | Attach correct nozzle (tangerine for hard | |||||||
|
|
|
|
|
|
|
|
|
| floors, green for carpets) - Pg. | |||||
Water | escaping | 1. | Dirty Water | Tank Is full. |
| 1. | Empty Dirty Water | Tank- | Pg. | t3 | |||||
from | All | Surface | 2. | Clean/Dirty | Water Tank | not | 2. | Secure Tank- | Pg. 13 |
|
| ||||
Floor | Cleaner |
| installed | properly. |
|
|
|
|
|
|
|
| |||
|
|
|
| 3. | Solution | trigger pulled. |
| 3. | Release | solution trigger. |
|
| |||
All Surface | Floor | 1. | Clean/Dirty | Water Tank | not | 1, | Secure Tank. |
|
|
|
| ||||
Cleaner | won't |
| installed | properly. |
|
|
|
|
|
|
|
| |||
dispense | solution | 2, | Clean Water Tank empty. | 2, | Fill Clean Water Tank. |
|
| ||||||||
|
|
|
| 3. | Solution | trigger not pulled | 3. | Pull solution | trigger. |
|
| ||||
Brushroll |
| not | 1. | Brush On/Off switch not in | 1. | Move Brush On/Off switch to ON position. | |||||||||
rotating |
|
| 2. | ON position |
|
|
|
|
|
|
|
| |||
|
|
|
| Brushrolt | clogged |
| 2. | Unplugunit. Remove debris from brushroll | |||||||
|
|
|
| 3. | Belt broken |
|
|
| and push brushrollreset button. | ||||||
|
|
|
|
|
| 3. | Take to Sears Service Center. |
16