10 / English | Nilfisk-Advance America BR 600S Series manual

A-10 / ENGLISH

DETERGENT SYSTEM PREPARATION AND USE (AXP/EDS MODELS ONLY)

COMMON INSTRUCTIONS:

The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over ﬂoor drain before purging because a small amount of detergent will be dispensed in the process.

To Purge When Changing Chemicals:

1Disconnect and remove the detergent cartridge.

2Turn the Key Switch (J) ON and press the Detergent ON/OFF Switch (S) and the Flow Rate Switch (T) down for at least 3 seconds. NOTE: Once activated the Flow Rate Indicator (U) will begin to ﬂash and will automatically shut off after 10 seconds. Normally one purge cycle is adequate to purge the system.

To Purge Weekly:

1Disconnect and remove the detergent cartridge. Install and connect a Cartridge ﬁlled with clean water

after 10 seconds. Normally one purge cycle is adequate to purge the system. The Detergent Box (AA) has a Detergent Level Viewing Slot (BB) for keeping track of how much detergent is remaining in the cartridge. When the detergent level is nearing the bottom of this slot it is time to reﬁll or replace the cartridge.

General Use:

The detergent (AXP/EDS) system is turned on when the Key Switch (J) is turned on but no detergent is dispensed until the scrub system is activated and the Drive Pedal

(8)pushed forward. The solution ﬂow rate automatically defaults to the last setting used. The solution ﬂow rate can be varied by subsequently pressing the Flow Rate Switch (T). There are four solution ﬂow rates indicated by the Flow Rate Indicator

(U). The detergent ﬂow rate increases or decreases with the solution ﬂow rate but the detergent ratio remains the same. During scrubbing, the detergent system can be turned off at any time by pressing the Detergent ON/OFF Switch (S) to allow scrubbing with water only. The solution ﬂow rate is controlled by the Flow Rate Switch (T) whether the detergent system is ON or OFF.

SERVICE NOTE: Follow the “To Purge Weekly” instructions above if the machine is going to be stored for an extended period of time or if you plan to discontinue use of the detergent (AXP/EDS) system.

DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry Break Cap (DD) as shown.

NON-DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Fill the detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to ﬁlling to avoid spilling detergent on the machine.

It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider (EE) on one end that needs to be set to the proper dilution ratio according to the dilution instructions on the manufacturer’s bottle. Slide the Magnet Slider (EE) to the appropriate location on Detergent Dilution Ratio Decal (FF). When installing a new cartridge, remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry Break Cap (DD) as shown.

A-10- FORM NO. 56041554 - Advenger™, Advenger™ AXP / BR 600S series

revised 3/06

BR 600S Series specifications

The Nilfisk-Advance America BR 600S Series is a remarkable line of ride-on scrubber-dryers designed to enhance cleaning efficiency in a variety of commercial settings. This series combines user-friendly operation with advanced technology to deliver superior cleaning performance for medium to large areas such as warehouses, retail spaces, and industrial facilities.

One of the most prominent features of the BR 600S Series is its innovative scrubbing system. The scrubber utilizes a dual brush design that efficiently covers larger surface areas, providing thorough cleaning and a consistent finish. The machine’s adjustable brush pressure allows operators to customize the scrubbing intensity based on the specific type of flooring, ensuring optimal results whether cleaning hard surfaces or more delicate materials.

Equipped with advanced water management technology, the BR 600S Series optimizes water usage while maintaining effective cleaning. The machine features a unique solution control system that ensures the right amount of water and cleaning solution is applied at all times. This not only reduces water consumption but also minimizes detergent waste, making the machine environmentally friendly and cost-effective.

The BR 600S Series is powered by a high-performance battery system, providing extended runtimes and reducing the need for frequent recharging. The inclusion of an onboard charger simplifies operation, allowing for quick and convenient charging between cleaning tasks. This makes the BR 600S ideal for busy environments that require minimal downtime.

Safety and comfort are paramount in the design of the BR 600S. The spacious operator compartment is ergonomically designed for ease of use, featuring intuitive controls that get operators up and running quickly. The low noise level of the machine also ensures that cleaning can take place during business hours without disrupting operations.

In addition to its performance features, the BR 600S Series emphasizes reliability and durability. Built with high-quality materials, these scrubbers are designed to withstand the rigors of daily use in challenging conditions, thus reducing maintenance costs and extending the lifespan of the machine.

Overall, the Nilfisk-Advance America BR 600S Series stands out in the market for its combination of advanced technology, enhanced cleaning efficiency, and user-friendly design, making it an ideal choice for facilities looking to elevate their cleaning operations.