Nilfisk-Advance America BR 600S Series manual English / A-13, After USE, Maintenance Schedule

Page 13

ENGLISH / A-13

AFTER USE

1When finished scrubbing, press the Scrub Off Switch (B) twice, this will automatically raise, retract and stop all the machine systems (brush, squeegee, vacuum, solution and detergent (AXP/EDS models)). Then drive the machine to a service area for daily maintenance and review of other needed service up keep.

2To empty the solution tank, remove the Solution Drain Hose (4) from its storage clamp. Direct the hose to a designated “DISPOSAL SITE” and remove the plug. Rinse the tank with clean water.

3To empty the recovery tank, pull the Recovery Tank Drain Hose (21) from its storage area. Direct the hose to a designated “DISPOSAL SITE” and remove the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled flow of waste water). Rinse the tank with clean water.

4Remove the brushes or pad holders. Rinse the brushes or pads in warm water and hang up to dry.

5Remove the squeegee, rinse it with warm water and re-install on mount.

6Remove the hopper on cylindrical systems and clean thoroughly. Remove from either side of the machine by opening the skirt and tilting the hopper up and away from housing, then pull out.

7Check the maintenance schedule below and perform any required maintenance before storage

MAINTENANCE SCHEDULE

MAINTENANCE ITEM

Daily

Weekly

Monthly

Yearly

Charge Batteries

X

 

 

 

Check/Clean Tanks & Hoses

X

 

 

 

Check/Clean/Rotate the Brushes/Pads

X

 

 

 

Check/Clean the Squeegee

X

 

 

 

Check/Clean Vacuum Shut-Off Float

X

 

 

 

Check/Clean the vacuum motor foam filter(s)

X

 

 

 

Clean Hopper on Cylindrical System

X

 

 

 

Check Each Battery Cell(s) Water Level

 

X

 

 

Inspect Scrub Housing Skirts

 

X

 

 

Inspect and clean Solution Filter

 

X

 

 

Check Foot/ Parking Brake For Wear & Adjustment

 

X

 

 

Clean Solution Trough on Cylindrical System

 

X

 

 

Purge Detergent System (AXP/EDS only)

 

X

 

 

Lubrication - Grease Fittings

 

 

X

 

* Check Carbon Brushes

 

 

 

X

*Have Nilfisk-Advance check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor carbon brushes check every 500 hours or once a year.

NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.

8Store the machine indoors in a clean dry place. Keep from freezing. Leave the tanks open to air them out.

9Turn the Master Key Switch (J) OFF (O) and remove the key.

LUBRICATING THE MACHINE

Once a month, pump a small amount of grease into each grease fitting on the machine until grease seeps out around the bearings.

Grease fitting locations are:

•Squeegee Caster Wheel Axle

•Steering Wheel Shaft Universal joint

Once a month, apply light machine oil to lubricate the:

•Steering Chain

•General Pivot Points For the Squeegee, Brush Linkage and Side Skirts

•Squeegee mount angle adjustment knob threads

revised 3/06

FORM NO. 56041554 - Advenger™, Advenger™ AXP / BR 600S series - A-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Advenger, Advenger AXP BR 600S series English English / A-3 SymbolsConsignes DE Prudence ET DE Sécurité Symboles Know Your Machine English / A-5Control Panel Install the Batteries Description of the Battery Condition IndicatorsWhen Servicing Batteries English / A-7Install the Brushes Cylindrical System Install the Brushes Disc SystemFill the Solution Tank Install the SqueegeeEnglish / A-9 Detergent System Preparation and USE AXP/EDS Models only 10 / EnglishFront English / A-11Operating the Machine 12 / EnglishWET Vacuuming To ScrubEnglish / A-13 Maintenance ScheduleAfter USE Lubricating the Machine14 / English Checking the Battery Electrolyte LevelCharging the Batteries Squeegee Adjustment Squeegee MaintenanceEnglish / A-15 Side Skirt Height Adjustment Disc System Side Skirt Maintenance Disc System16 / English To reverse or replace the scrub system side skirtsEnglish / A-17 Side Skirt Maintenance Cylindrical SystemTo replace the scrub system side skirts Problem Possible Cause Remedy General Machine Troubleshooting18 / English Model English / A-19Español Español / B-3 Precauciones Y Advertencias SímbolosConozca SU Máquina Panel DE Control Español / B-5Instalación DE LAS Baterías Descripción DE LOS Indicadores DE Situación DE LAS BateríasEstándar Alternativo Cuando revise las bateríasInstalación DE LOS Cepillos Sistema DE Disco Español / B-7Instalación DE LOS Cepillos Sistema Cilíndrico Instalación DE LA BoquillaInstrucciones Comunes Reparación Y USO DEL Sistema DE Detergente AXP/EDSEspañol / B-9 Manejo DE LA Máquina 10 / EspañolAspiración EN Húmedo Para fregarDespués DE LA Utilización Español / B-11Programa DE Mantenimiento Lubricación DE LA MáquinaRecarga DE Baterías 12 / EspañolComprobación DEL Nivel DE Electrolitos DE LAS Baterías Mantenimiento DE LA Boquilla Español / B-13Ajuste DE LA Boquilla Ajuste del ángulo de la boquillaMantenimiento DE LA Faldilla Lateral Sistema DE Discos 14 / EspañolMantenimiento DE LA Faldilla Lateral Sistema Cilíndrico Español / B-15Problema Posible causa Solución Solución DE Problemas Generales DE LA Máquina16 / Español Véase el manual de servicioModelo Español / B-17Page Page EU Överensstämmelseförsäkran EU Overensstemmelseserklæring Déclaration CE de conformitéEG-conformiteitsverklaring EU Declaration of ConformityEU Prohlášení o shodě Deklaracja zgodności z normami UE Deklaracija EU o skladnosti Prehlásenie o súlade EÚEU megfelelőségi nyilatkozat 2006

BR 600S Series specifications

The Nilfisk-Advance America BR 600S Series is a remarkable line of ride-on scrubber-dryers designed to enhance cleaning efficiency in a variety of commercial settings. This series combines user-friendly operation with advanced technology to deliver superior cleaning performance for medium to large areas such as warehouses, retail spaces, and industrial facilities.

One of the most prominent features of the BR 600S Series is its innovative scrubbing system. The scrubber utilizes a dual brush design that efficiently covers larger surface areas, providing thorough cleaning and a consistent finish. The machine’s adjustable brush pressure allows operators to customize the scrubbing intensity based on the specific type of flooring, ensuring optimal results whether cleaning hard surfaces or more delicate materials.

Equipped with advanced water management technology, the BR 600S Series optimizes water usage while maintaining effective cleaning. The machine features a unique solution control system that ensures the right amount of water and cleaning solution is applied at all times. This not only reduces water consumption but also minimizes detergent waste, making the machine environmentally friendly and cost-effective.

The BR 600S Series is powered by a high-performance battery system, providing extended runtimes and reducing the need for frequent recharging. The inclusion of an onboard charger simplifies operation, allowing for quick and convenient charging between cleaning tasks. This makes the BR 600S ideal for busy environments that require minimal downtime.

Safety and comfort are paramount in the design of the BR 600S. The spacious operator compartment is ergonomically designed for ease of use, featuring intuitive controls that get operators up and running quickly. The low noise level of the machine also ensures that cleaning can take place during business hours without disrupting operations.

In addition to its performance features, the BR 600S Series emphasizes reliability and durability. Built with high-quality materials, these scrubbers are designed to withstand the rigors of daily use in challenging conditions, thus reducing maintenance costs and extending the lifespan of the machine.

Overall, the Nilfisk-Advance America BR 600S Series stands out in the market for its combination of advanced technology, enhanced cleaning efficiency, and user-friendly design, making it an ideal choice for facilities looking to elevate their cleaning operations.
Top Page Image Contents