Harman-Kardon AVR 8500 owner manual DTS-ES 6.1 Discrete DTS-ES 6.1 Matrix, DTS + NEO6, Coaxial Ó

Page 6

Front Panel Controls

8Tone Mode: Pressing this button enables or disables the Bass and Treble tone controls. When the button is pressed so that the words TONE INappear in the Main Information Display

ˆ the Bass and Treble controls will be enabled. When the button is pressed so that the words TONEOUTappear in the Main Information Display ˆ, the output signal will be “flat,” without any bass or treble alteration.

9DSP Surround Mode Selector: Press this button to select the following DSP Surround Modes: VMAx Near/Far, Hall 1, Hall 2 or Theater. (See page 30 for more information about sur- round modes.)

)Tuning Selector: Press the left side of the button to tune lower frequency stations and the right side of the button to tune higher frequency stations. When a station with a strong signal is reached, the TUNED indicator Iwill illuminate in the Main Information Display ˆ (see page 43 for more information on tuning stations).

!Tuner Band Selector: Pressing this button will automatically switch the AVR to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands. Holding it pressed for 3 seconds will switch between stereo or mono receiving and automatic or manual tuning mode. When the button is pressed so that the AUTO Indicator Jlights, the tuner will search for the next station with an acceptable signal when the Tuning Selector )Kéis pressed. When the button is pressed so that the AUTO Indicator Jis not lit, each press of the Tuning Selector )Kéwill increase the frequency. (See page 42 for more information on using the tuner.)

@6CH/8CH Direct Button: Press this button to select the 6 Channel Direct or 8 Channel DIrect inputs as the AVR's source.

#Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 42 for more information on tuner pro- gramming.)

$Stereo Mode Selector /› Button: This button has two functions: In normal use, pressing this selector button cycles through the stereo modes, and it is also used to turn off all surround processing and place the unit in a traditional two-channel Stereo mode. The first press selects 5-Channel Stereo or 7-Channel Stereo, depend- ing on the selection (5.1 or 6.1/7.1) made in the surround mode setting, see page 24, and the sec- ond selects “SURROUND OFF,” which is true Stereo.

%Input Source Selector: Press this button to change the input by scrolling through the list of input sources.

^RDS Select Button: Press this button to dis- play the various messages that are part of the RDS data system of the AVR’s tuner. (See page 43 for more information on RDS).

&DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the vari- ous DTS Neo:6 modes, which extract a five- or seven-channel surround field from two-channel program material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode in the following order:

DTS Neo:6 MUSIC

DTS Neo:6

CINE

NOTE: The front panel digital audio, video and analog audio input and output jacks are normally concealed behind a drop-down door in the lower right corner of the front panel. To access these jacks, open the panel door by gently pulling down the upper right corner of the door as indicated by ”PULL/OPEN”.

*Optical Digital 4 Input Jack: Connect the optical digital audio output of an audio or video product to this jack.

(Optical Digital 4 Output Jack: Connect this jack to the optical digital input of a digital recorder to send a feed of the digitial output when a PCM digital input source is in use by the AVR.

ÓCoaxial Digital 4 Input Jack: Connect the output of a digital audio source to this jack.

ÔCoaxial Digital 4 Output Jack: Connect this jack to the coaxial digital input of a digital recorder to send a feed of the digitial output when a PCM digital input source is in use by the AVR.

Input/Output Status Indicators: This LED indicator will normally light green to show that the front panel Video 5 A/V Òjacks are operating as an input. When these jacks are con- figured for use as an output, the indicator will turn red to show that the jack may be used for recording. (See page 21 for more information on configuring the front panel jacks as outputs, rather than inputs.)

ÒVideo 5 Input/Output Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/ video products such as camcorders and portable audio players. They may also be configured as output jacks (also S-Video) to feed a signal to any recording Audio or Video device (see page 37 for more information).

ÚDTS Surround Mode Selector: When a DTS source is in use the AVR will select the appropriate mode automatically and no other mode will be available, except THX or Logic 7 processing. In that case, pressing that button will display the mode currently selected by the AVR´s decoder. Depending on the surround material played and the speaker setting, one of the following modes will be selected by the unit:

•DTS-ES 6.1 DISCRETE

•DTS-ES 6.1 MATRIX

•DTS + NEO:6

•DTS 5.1

Both DTS ES 6.1 Modes and DTS+NEO:6 will be selected only when surround back speakers have been configured with your system: DISCRETE with appropriate source material, MATRIX with 6.1 Matrix recordings and DTS+NEO:6 with normal DTS 5.1 channel recordings. The DTS 5.1 mode will be selected with any DTS source, when no surround back speakers are configured (see also pages 25 and 33-36). When the THX mode was selected by pressing the HOME THX button

6pressing this button will escape from the THX processing mode.

ÛDigital Select Button: When playing a source that has a digital output, press this button

to select between the Optical *

and

Coaxial Ó

Digital inputs (See page

35 for more information).

 

ÙVolume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR is muted, adjust- ing volume control will automatically release the unit from the silenced condition.

ıInput indicators: A green LED will light in front of the input that is currently being used as the source for the AVR.

ˆMain Information Display: This display delivers messages and status indications to help you operate the receiver. (See pages 7–8 for a complete explanation of the Information Display.)

˜Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.

¯Surround Mode Indicators: A green LED will light in front of the surround mode or digital bitstream format (HDCD, MP3 or PCM) that is currently in use.

Note that depending of specific combination of input sources and surround mode selected, more than one indicator may light.

6FRONT PANEL CONTROLS

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Power for the Digital Revolution AVR 8500 Audio/ Video ReceiverTable of Contents Declaration of ConformityHdcd Decoding for Superb CD Playback Description and FeaturesIntroduction IntroductionSafety Information Important Safety InformationUnpacking Home THX Mode Selector Press this Power Indicator #Preset Station SelectorHeadphone Jack $Stereo Mode Selector /› Button Front Panel ControlsTo select between the Optical DTS-ES 6.1 Discrete DTS-ES 6.1 MatrixDTS + NEO6 Coaxial ÓMulti Indicator Auto Indicator Front Panel Information DisplayFront Panel Information Display Rear Panel Connections Channel Direct Inputs If an externalRear Panel Connections Unswitched Outlet Power On Button Power Off ButtonProgram/SPL Indicator Surround Mode SelectorMain Remote Control Functions Channel Direct InputsMain Remote Control Functions Main Remote Control Functions Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Video Connection Notes Scart A/V ConnectionsComponent Video Inputs . Note that even Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters Also other colours possible, e.g. brown and greySystem and Power Connections Speaker Placement AC Power ConnectionSpeaker Selection System Configuration System ConfigurationUsing the On-Screen Display First Turn OnInput Setup Optional, external power amplifiers Speaker Setup¤ Button Dto begin the speaker configura- tion process Front panel orSurround SubwooferOn the remote so that Sublfe appears in the on-screen menu Surround Setup Within five seconds, either press ⁄/¤ buttonsTHX Surround EX and DTS Settings Independent of the Input Selected Adjustments for Other InputsDelay Settings On the remote. Then press the ⁄/¤ buttons Night Mode SettingsOutput Level Adjustment To select the DOLBYmenu see figTurn off the OSD system if it is in use Using EzSetPress and hold the SPL Indicator Select So that on is highlightedSensor and Indicator off When all channels have the same output levelMenu Bass Peak Limiter Surround Mode Chart OperationHall Dolby 3 StereoTheater OFF StereoControls and Use of Headphones Basic OperationSource Selection Digital Audio Playback Surround Mode SelectionOne of the most important features Until Surr OFF appears in the Main Information Display ˆPCM Audio Playback Dolby DigitalDolby Digital Surround EX MP3 Audio PlaybackDigital Bitstream Indicators Selecting a Digital SourceSpeaker/Channel Indicators Eand adjust to accommodate itOFF Indicator off Output Level Adjustment With Source SignalsIndicator Select Tape RecordingTo change the output level Memory BackupChannel/8-Channel Direct Input Will not functionTurn On Volume Level Advanced FeaturesSpeaker Reset Advanced FeaturesSemi-OSD Settings Full-OSD Time Out AdjustmentMultiroom Operation InstallationMultiroom Setup Multiroom OperationTuner Operation Basic Tuner OperationRDS Operation Direct Code Entry Time. When the Program/SPL IndicatorProgramming the Remote with Codes Auto-Search MethodLearning Codes from a Remote Programming the RemoteCode Readout Erasing Learned CodesErasing Macro Commands Macro ProgrammingPress the AVR Selector Remote With Other Devices Volume Punch-ThroughProgrammed Device Functions 4and the Mute buttonChannel Control Punch-Through Selector buttonResetting the Remote Memory Function List Function ListScan Scan + Rewind Play Fast Fwd Record Stop Pause Power On Power Off Mute TV Select Channel +Power On Power Off VID 3 Select Channel + Prev Channel 1 2 3 4 5 6 7 ClearTroubleshooting Guide Processor ResetTroubleshooting Guide Technical Specifications Harman Consumer International

AVR 8500 specifications

The Harman-Kardon AVR 8500 is a high-performance audio/video receiver designed for enthusiasts who demand exceptional sound quality and advanced features. This model is part of the premium AVR line and has become a respected staple in home theater setups since its introduction.

One of the standout features of the AVR 8500 is its robust amplification system. With a powerful output of 120 watts per channel, it drives even the most demanding speakers and ensures a dynamic audio experience. The receiver supports a variety of surround sound formats, including Dolby Digital, Dolby Pro Logic II, DTS, and THX Surround EX, delivering an immersive listening experience for movies, games, and music.

The AVR 8500 also showcases a range of advanced processing technologies that enhance audio fidelity. Harman-Kardon’s proprietary Logic 7 processing allows for the seamless upmixing of stereo content to surround sound, providing a richer soundscape. Additionally, the integration of the latest HDMI inputs ensures that high-definition audio and video signals can be transmitted without degradation in quality. This model typically includes multiple HDMI ports, along with support for 4K video passthrough, making it an ideal choice for modern home theater configurations.

In terms of connectivity, the AVR 8500 offers versatility, featuring multiple analog and digital audio inputs, a variety of video connections, and even network capabilities for streaming music from popular services directly. The receiver often comes equipped with advanced room correction technologies, such as Harman’s proprietary room setup and calibration system, which helps to optimize sound quality based on the specific characteristics of your listening environment.

Another notable characteristic of the Harman-Kardon AVR 8500 is its user-friendly interface. The intuitive on-screen setup allows users to easily configure their audio and video settings, making it accessible not only for seasoned audiophiles but also for those new to home theater systems.

A sleek design further complements its high-performance capabilities, ensuring that the AVR 8500 not only performs well but also looks great in any entertainment setup. The combination of its advanced technological features, extensive connectivity options, and impressive sound quality makes the Harman-Kardon AVR 8500 a premier choice for anyone seeking to elevate their home audio experience.
Top Page Image Contents