Kenmore 350 Series Install 3-Valve Bypass, Installing Holding Clips, Bypass Valve Turned Downward

Page 12

Install Plastic Bypass Valve

Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port.

Turbine	Sensor Port
Support

Turbine

FIG. 10

INSTALLING HOLDING CLIPS

	Bypass Valve or	Black Clip	Cross Section of Valve
		Black Clip	Inlet or Outlet

	Installation Adaptor
	Installation Adaptor

O-Ring

Clip Snaps into Place

Between Larger Diameter Rings

FIG. 11

BYPASS VALVE TURNED DOWNWARD

Turn bypass valve upside down to connect to floor level plumbing.

OUT

IN

FIG. 12

Install 3-Valve Bypass

INSTALLING 3 VALVE BYPASS AND PIPES

3 VALVE BYPASS

Complete the following steps to install the three (3) valve bypass:

•Cut the house main water pipe where you will con- nect the softener.

•Loosely put together pipe, fittings, and the three

(3) valves.

•Place valve(s) within easy reach.

When all pipe, fittings and valves make a good fit together, tighten all threaded joints (use pipe dope on outside threads), or solder all sweat joints.

TO	FIG. 13
Softener Inlet

Questions? Call The Kenmore Water Line 1-800-426-9345

12

Image 12

Contents Repair or Parts ? Call toll free Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksDisclaimer of implied warranties limitation of remedies Table of Contents Facts and Figures to KeepSafety Guides Unpack and Check Your Carton Parts DescriptionsSmall Parts Inspect ShipmentPlan Your Installation Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Soft, HotSuggested Slab Foundation Installation Draw in Your Pipes and FittingsOUT PIPE, FITTINGS, Other Materials NeededRead Before Beginning Installation Before Installing Checks & TestsInstall Plastic Bypass Valve Assemble Inlet Outlet ADAPTORS, or Plastic Bypass ValveBypass Valve Inlet and Outlet Threaded AdaptorsInstall 3-Valve Bypass Installing Holding ClipsInstalling 3 Valve Bypass and Pipes Valve BypassLocate Water Softener and Connect Pipes Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Valve and Salt Tank Drains Connect the Valve Drain HoseConnect Salt Tank Overflow Tubing Leak Test House Main Water Shutoff ValvesSingle Bypass Leak TestWater Meter Jumper Wire Connecting TransformerElectrical Requirements Cold Water Pipe GroundingInstall Covers and Restart Water Heater Program The TimerInstall Covers Program the TimerSET Present Time of DAY SET Water Hardness NumberSET Regeneration Time Sanitize The Water Softener Sanitize the Water SoftenerSanitize Your Water Softener AS Follows Adding Salt To The Storage Tank Adding Salt to the Storage TankWater Softening Salt with Iron Removing Additives Check List of STEP-BY-STEP Guides to Install Check ListFaceplate Timer Features 12 / 24 Hour Clock California Efficiency RequirementWater Flow Through the Softener Recharge Time Remaining and Valve Position Indicators Error CodeKENMORE’S Ultra Cleansing Feature Program MemoryWater Flow Through Softener in Service Soft Water Service and RegenerationHow Your Water Softener Works Water Flow Through Softener in FillWater Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashWater Flow Through Softener Fast Rinse Automatic BypassElectronics Care Of Your Water Softener Salt BridgeSalt Bridge Keeping the Water Softener Clean Iron from Resin BEDNozzle & Venturi Drain ALL Water from Softener Protect the Water Softener from FreezingProblem Cause Correction Checklist to Help YOU Save MoneySpecifications Model 38356 Timer Code S Model 39356 Timer Code SBypass Valves InchesOther Specifications Service Tech Information Wiring SchematicFaceplate Always Make These Initial Checks FirstProcedure for Removing Error Code from Faceplate Possible Defect CodeTroubleshooting Valve Position Indicators Timer PWA ReplacementOther Information ModelBrine Valve Float Setting Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Rotary Valve Service DisassemblyAssembly To Relieve PressureWater Flow Through the Softener Valve Service Cycle Fill CycleBrining and Brine Rinse Cycle Water Flow Through the Softener Valve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleExploded View Parts List Water Softener CompletePart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours