Kenmore 625.393560, 350 Series warranty Service Tech Information, Wiring Schematic, Faceplate

Page 35

Service Tech Information

WIRING SCHEMATIC

24 VAC

Transformer




Turbine	OUT
Turbine		GND
Sensor		GND
Sensor	+5

FACEPLATE

350 Series

BACK OF TIMER

(PWA)

AC INPUT			POS / TURBINE	MOTOR

valve motor

	grn
	NO	Position
		Position
brn	NC	Switch
	NC

Capacity Plus

Ultracleansing

Adjustable Low Salt Indicator

Keep this manual with your water softener. If repairs are needed, the service technician must have the informa- tion on the following pages.

ALWAYS MAKE THESE INITIAL CHECKS FIRST

1.Does the time display show the correct time of day?

•If display is blank, check power source to the sof- tener.

•If time is flashing, power was off for over 6 hours. The softener resumes normal operation but regen- erations occur at the wrong time.

•If an error code (Example: Err3) shows in the face- plate display, go to AUTOMATIC ELECTRONIC DIAGNOSTICS.

2.Plumbing bypass valve(s) must be fully in service position.

3.The inlet and outlet pipes must connect to the softener inlet and outlet respectively.

4.Is the transformer plugged into a “live”, grounded wall outlet, and the power cable fastened secure- ly to the controller?

FIG. 51

5.The valve drain hose must be free of kinks and sharp bends, and not elevated over 8 ft. above the floor.

6.Is there salt in the storage tank?

7.Is the brine tubing connected? Brine tubing con- nects to nozzle venturi and brine valve assembly.

8.Is the brine valve float set right?

9.Press the SELECT button two times to display the hardness setting.

Be sure it is the correct setting for the household’s water supply. (Make a hardness test of the raw water and compare with the hardness setting. Also test a soft water sample to verify if a problem exists.) Press the SELECT button twice more to return to present time in the display.

If you do not find the problem after making initial checks, do the MANUAL INITIATED ELECTRONIC DIAGNOSTICS, and the MANUAL ADVANCE REGEN-

ERATION CHECK.

Questions? Call The Kenmore Water Line 1-800-426-9345

35

Image 35

Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerTEN Year Limited Warranty Against Leaks Facts and Figures to Keep Table of ContentsSafety Guides Inspect Shipment Unpack and Check Your CartonParts Descriptions Small PartsTools Needed Plan Your InstallationProper Order to Install Water Treating Equipment Plan Your InstallationSoft, Hot Where to Install the Water SoftenerDraw in Your Pipes and Fittings Suggested Slab Foundation InstallationPIPE, FITTINGS, Other Materials Needed OUTBefore Installing Checks & Tests Read Before Beginning InstallationInlet and Outlet Threaded Adaptors Install Plastic Bypass ValveAssemble Inlet Outlet ADAPTORS, or Plastic Bypass Valve Bypass ValveValve Bypass Install 3-Valve BypassInstalling Holding Clips Installing 3 Valve Bypass and PipesPosition Softener Into Place Locate Water Softener and Connect PipesMove Softener Into Place Typical Soldering ConnectionsConnect Salt Tank Overflow Tubing Connect Valve and Salt Tank DrainsConnect the Valve Drain Hose Leak Test Leak TestHouse Main Water Shutoff Valves Single BypassCold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical RequirementsProgram the Timer Install Covers and Restart Water HeaterProgram The Timer Install CoversSET Regeneration Time SET Present Time of DAYSET Water Hardness Number Sanitize Your Water Softener AS Follows Sanitize The Water SoftenerSanitize the Water Softener Water Softening Salt with Iron Removing Additives Adding Salt To The Storage TankAdding Salt to the Storage Tank Check List Check List of STEP-BY-STEP Guides to InstallFaceplate Timer Features California Efficiency Requirement 12 / 24 Hour ClockWater Flow Through the Softener Program Memory Recharge Time Remaining and Valve Position IndicatorsError Code KENMORE’S Ultra Cleansing FeatureWater Flow Through Softener in Fill Water Flow Through Softener in ServiceSoft Water Service and Regeneration How Your Water Softener WorksWater Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseElectronics Water Flow Through Softener Fast RinseAutomatic Bypass Salt Bridge Care Of Your Water SoftenerSalt Bridge Nozzle & Venturi Keeping the Water Softener CleanIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money Problem Cause CorrectionInches SpecificationsModel 38356 Timer Code S Model 39356 Timer Code S Bypass ValvesOther Specifications Always Make These Initial Checks First Service Tech InformationWiring Schematic FaceplatePossible Defect Code Procedure for Removing Error Code from FaceplateModel Troubleshooting Valve Position IndicatorsTimer PWA Replacement Other InformationCycle Flow Rates Gallons PER MIN Brine Valve Float SettingManual Advance Regeneration Check To Relieve Pressure Rotary Valve ServiceDisassembly AssemblyBrining and Brine Rinse Cycle Water Flow Through the Softener Valve Service CycleFill Cycle Fast Rinse Cycle Water Flow Through the Softener Valve Backwash CycleFast Rinse Cycle Backwash CycleExploded View Part Number Part Description Parts ListWater Softener Complete Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours