Kenmore 625.393560 Install Covers and Restart Water Heater, Program The Timer, Program the Timer

Page 17

Install Covers and Restart Water Heater

INSTALL COVERS

After installing your water softener, replace the covers. Angle the covers so the main cover clips onto the back first, then bring down in front and clip on the two (2) tabs inside the rim of the salt hole and lower the salt cover closed. See Fig. 23.

Cover (Main)

Salt Hole Cover

RESTART THE WATER HEATER

Turn on the gas (or electric) supply to the water heater and light the pilot.

YOUR PLUMBING INSTALLATION AND ELECTRICAL

WORK ARE NOW COMPLETE.

FIG. 23

Program The Timer

Display

UP Button

SELECT Button

350 Series

Capacity Plus

Ultracleansing

Adjustable Low Salt Indicator

REGENERATION Button

PROGRAM THE TIMER

1.When the transformer is plugged in, a model code and a test number (example: J11) show in the face plate. This will display for four (4) seconds. Then, 12:00 AM and PRESENT TIME begin to flash.

NOTE: If “- - - -” shows in the display, press the UP or DOWN button until either S 32, for Model 38356, or S 33, for Model 39356, shows in the display Then, press the SELECT button to set, and change to the flashing PRESENT TIME display.

2.To check the model code, unplug the transformer at the wall outlet and plug in again. If other than this code shows, refer to the Troubleshooting Section. SOUND “BEEPER”: A “beeper” sounds while pressing buttons for timer setup. One beep signals a change in the face plate display. Repeated beeps mean the timer will not accept a change from the button you have pressed, telling you to use another button. For example, while setting the hardness the beeper sounds repeatedly when the display reaches 1 using the DOWN button, or the highest hard- ness setting using the UP button.

DOWN Button

Model 38356

Model 39356

FIG. 24

AM

PRESENT TIME

AM

PRESENT TIME

FIG. 25

Questions? Call The Kenmore Water Line 1-800-426-9345

17

Image 17
Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerTEN Year Limited Warranty Against Leaks Facts and Figures to Keep Table of ContentsSafety Guides Parts Descriptions Unpack and Check Your CartonSmall Parts Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationPlan Your Installation Tools NeededSoft, Hot Where to Install the Water SoftenerDraw in Your Pipes and Fittings Suggested Slab Foundation InstallationPIPE, FITTINGS, Other Materials Needed OUTBefore Installing Checks & Tests Read Before Beginning InstallationAssemble Inlet Outlet ADAPTORS, or Plastic Bypass Valve Install Plastic Bypass ValveBypass Valve Inlet and Outlet Threaded AdaptorsInstalling Holding Clips Install 3-Valve BypassInstalling 3 Valve Bypass and Pipes Valve BypassMove Softener Into Place Locate Water Softener and Connect PipesTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect Valve and Salt Tank DrainsConnect the Valve Drain Hose House Main Water Shutoff Valves Leak TestSingle Bypass Leak TestConnecting Transformer Water Meter Jumper WireElectrical Requirements Cold Water Pipe GroundingProgram The Timer Install Covers and Restart Water HeaterInstall Covers Program the TimerSET Regeneration Time SET Present Time of DAYSET Water Hardness Number Sanitize Your Water Softener AS Follows Sanitize The Water SoftenerSanitize the Water Softener Water Softening Salt with Iron Removing Additives Adding Salt To The Storage TankAdding Salt to the Storage Tank Check List Check List of STEP-BY-STEP Guides to InstallFaceplate Timer Features California Efficiency Requirement 12 / 24 Hour ClockWater Flow Through the Softener Error Code Recharge Time Remaining and Valve Position IndicatorsKENMORE’S Ultra Cleansing Feature Program MemorySoft Water Service and Regeneration Water Flow Through Softener in ServiceHow Your Water Softener Works Water Flow Through Softener in FillWater Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseElectronics Water Flow Through Softener Fast RinseAutomatic Bypass Salt Bridge Care Of Your Water SoftenerSalt Bridge Nozzle & Venturi Keeping the Water Softener CleanIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money Problem Cause CorrectionModel 38356 Timer Code S Model 39356 Timer Code S SpecificationsBypass Valves InchesOther Specifications Wiring Schematic Service Tech InformationFaceplate Always Make These Initial Checks FirstPossible Defect Code Procedure for Removing Error Code from FaceplateTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information ModelCycle Flow Rates Gallons PER MIN Brine Valve Float SettingManual Advance Regeneration Check Disassembly Rotary Valve ServiceAssembly To Relieve PressureBrining and Brine Rinse Cycle Water Flow Through the Softener Valve Service CycleFill Cycle Fast Rinse Cycle Water Flow Through the Softener Valve Backwash CycleBackwash Cycle Fast Rinse CycleExploded View Part Number Part Description Parts ListWater Softener Complete Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours