Kenmore 350 Series SET Present Time of DAY, SET Water Hardness Number, SET Regeneration Time

Page 18

Program The Timer

SET PRESENT TIME OF DAY

If the words PRESENT TIME do not show in the display, press the SELECT button until they do show in the display. Press the UP or DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward. If the present time is between noon and midnight, be sure PM shows. If the present time is between midnight and noon, be sure AM shows. Each press of the UP or DOWN buttons changes the time by one (1) minute. Holding the buttons in changes the time 32 minutes each second.

PM

PRESENT TIME

AM

PRESENT TIME

FIG. 26

SET WATER HARDNESS NUMBER

To set the water hardness number, complete the following steps:

1.Press the SELECT button once to display 25 (flashing) and HARDNESS. The grains per gallon (gpg) hardness of your water supply is on your water analysis report. Be sure to enter water test results on the Facts & Figure Chart on page 3.

2.If your water supply contains iron, compensate for it by adding to the water hardness number. For example, assume your water is 20 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each I ppm of iron. In this example, you would use 30 for your hardness num- ber.

2 ppm iron x 5 = 10

20 gpg hardness

+10

30 HARDNESS NUMBER

3.Press the UP or DOWN buttons to set your water hard- ness number in the display. The DOWN button moves the display to 1. The UP button moves the display to the high- est setting (see maximum setting for your model in the specifications).

NOTE: Each press of the UP or DOWN button changes the display by 1 between 1 and 25. Between 25 and the highest number, the display changes 5 at a time (25, 30, 35, etc.) Holding the UP or DOWN button in changes the display twice each second.

AM

HARDNESS

RECHARGE

TIME

FIG. 27

SET REGENERATION TIME

To complete setting the regeneration time, complete the fol- lowing steps:

1.Press the SELECT button to display 2:00 AM (flashing) and RECHARGE TIME.

2.At the 2:00 AM recharge time setting, the softener begins regeneration (see pages 26 - 28) at 2:00 AM. This is a good time in most households because water is not being used. If a different recharge time setting would be better for your household, complete the following step.

3.Press the UP or DOWN buttons to set the desired recharge starting hour. Be sure to observe the AM-PM as you did when setting the present time of day.

Note: Each press of the UP or DOWN buttons changes the display one hour. Holding the but- tons in changes the display twice each sec- ond.

4.Press the SELECT button once again, to com- plete initial programming, and the current time of day shows in the display.

Questions? Call The Kenmore Water Line 1-800-426-9345

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Repair or Parts ? Call toll free Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksDisclaimer of implied warranties limitation of remedies Table of Contents Facts and Figures to KeepSafety Guides Small Parts Unpack and Check Your CartonParts Descriptions Inspect ShipmentPlan Your Installation Plan Your InstallationProper Order to Install Water Treating Equipment Tools NeededWhere to Install the Water Softener Soft, HotSuggested Slab Foundation Installation Draw in Your Pipes and FittingsOUT PIPE, FITTINGS, Other Materials NeededRead Before Beginning Installation Before Installing Checks & TestsBypass Valve Install Plastic Bypass ValveAssemble Inlet Outlet ADAPTORS, or Plastic Bypass Valve Inlet and Outlet Threaded AdaptorsInstalling 3 Valve Bypass and Pipes Install 3-Valve BypassInstalling Holding Clips Valve BypassTypical Soldering Connections Locate Water Softener and Connect PipesMove Softener Into Place Position Softener Into PlaceConnect Valve and Salt Tank Drains Connect the Valve Drain HoseConnect Salt Tank Overflow Tubing Single Bypass Leak TestHouse Main Water Shutoff Valves Leak TestElectrical Requirements Water Meter Jumper WireConnecting Transformer Cold Water Pipe GroundingInstall Covers Install Covers and Restart Water HeaterProgram The Timer Program the TimerSET Present Time of DAY SET Water Hardness NumberSET Regeneration Time Sanitize The Water Softener Sanitize the Water SoftenerSanitize Your Water Softener AS Follows Adding Salt To The Storage Tank Adding Salt to the Storage TankWater Softening Salt with Iron Removing Additives Check List of STEP-BY-STEP Guides to Install Check ListFaceplate Timer Features 12 / 24 Hour Clock California Efficiency RequirementWater Flow Through the Softener KENMORE’S Ultra Cleansing Feature Recharge Time Remaining and Valve Position IndicatorsError Code Program MemoryHow Your Water Softener Works Water Flow Through Softener in ServiceSoft Water Service and Regeneration Water Flow Through Softener in FillWater Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashWater Flow Through Softener Fast Rinse Automatic BypassElectronics Care Of Your Water Softener Salt BridgeSalt Bridge Keeping the Water Softener Clean Iron from Resin BEDNozzle & Venturi Drain ALL Water from Softener Protect the Water Softener from FreezingProblem Cause Correction Checklist to Help YOU Save MoneyBypass Valves SpecificationsModel 38356 Timer Code S Model 39356 Timer Code S InchesOther Specifications Faceplate Service Tech InformationWiring Schematic Always Make These Initial Checks FirstProcedure for Removing Error Code from Faceplate Possible Defect CodeOther Information Troubleshooting Valve Position IndicatorsTimer PWA Replacement ModelBrine Valve Float Setting Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Assembly Rotary Valve ServiceDisassembly To Relieve PressureWater Flow Through the Softener Valve Service Cycle Fill CycleBrining and Brine Rinse Cycle Backwash Cycle Water Flow Through the Softener Valve Backwash CycleFast Rinse Cycle Fast Rinse CycleExploded View Parts List Water Softener CompletePart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours
Top Page Image Contents