Kenmore 300 Series warranty Program The Timer, Program the Timer, SET Present Time of DAY

Page 18

Program The Timer

Display

UP Button

REGENERATION Button

SELECT Button

PROGRAM THE TIMER

1.When the transformer is plugged in, a model code and a test number (example: J1.1) show in the face plate. This will display for four (4) seconds. Then, 12:00 PM and the words SET TIME begin to flash.

NOTE: If “- - - -” shows in the display, press the UP or DOWN button until either S 25, for model 38306, or S 26, for model 39306, shows in the display. Then, press the SELECT button to set, and change to the flashing SET TIME display.

2.To check the model code, unplug the transformer at the wall outlet and plug in again. If other than S 25 or S 26 shows, refer to the Troubleshooting Section.

SOUND “BEEPER”: A “beeper” sounds while pressing buttons for timer setup. One beep signals a change in the face plate display. Repeated beeps mean the timer will not accept a change from the button you have pressed, telling you to use another button. For example, while setting the hardness, the beeper sounds repeatedly when the display reaches 1 using the DOWN button, or the highest hard- ness setting using the UP button.

SET PRESENT TIME OF DAY

If the words SET TIME do not show in the display, press the SELECT button until they do show in the display. Press the UP or DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward. If the present time is between noon and midnight, be sure PM shows. If the present time is between midnight and noon, be sure AM shows. Each press of the UP or DOWN buttons changes the time by one (1) minute. Holding the buttons in changes the time 32 minutes each second.

Large Capacity

DOWN Button

FIG. 24

Model 38306

Model 39306

FIG. 25

FIG. 26

Questions? Call The Kenmore Water Line 1-800-426-9345

18

Image 18

Contents Repair or Parts ? Call toll free Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksDisclaimer of implied warranties limitation of remedies Table of Contents Facts and Figures to KeepSafety Guides Small Parts Unpack and Check Your CartonParts Descriptions Inspect ShipmentPlan Your Installation Plan Your InstallationProper Order to Install Water Treating Equipment Tools NeededTypical Installation Where to Install the Water SoftenerSuggested Slab Foundation Installation Draw in Your Pipes and FittingsOUT PIPE, FITTINGS, Other Materials NeededRead Before Beginning Installation Before Installing Checks & TestsInstall Plastic Bypass Valve Assemble Inlet Outlet ADAPTORS, or Plastic Bypass ValveBypass Valve Installing 3 Valve Bypass and Pipes Install 3-Valve BypassInstalling Holding Clips Valve BypassTypical Soldering Connections Locate Water Softener and Connect PipesMove Softener Into Place Position Softener Into PlaceConnect Valve and Salt Tank Drains Connect the Valve Drain HoseConnect Salt Tank Overflow Tubing Single Bypass Leak TestHouse Main Water Shutoff Valves Leak TestElectrical Requirements Water Meter Jumper WireConnecting Transformer Cold Water Pipe GroundingInstall Covers Install Covers and Restart Water HeaterInstall Covers Restart the Water HeaterProgram The Timer Program the TimerSET Present Time of DAY SET Water Hardness Number SET Regeneration TimeSET Salt Level Sanitize The Water Softener Sanitize the Water SoftenerSanitize Your Water Softener AS Follows Adding Salt To The Storage Tank Adding Salt to the Storage TankWater Softening Salt with Iron Removing Additives Check List of STEP-BY-STEP Guides to Install Check ListRecharge NOW Faceplate Timer FeaturesExtra Recharge Recharge TonightTo turn this setting on Efficiency ModeError Code Program MemoryHow Your Water Softener Works Water Flow Through Softener in ServiceSoft Water Service and Regeneration Water Flow Through Softener in FillWater Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashWater Flow Through Softener Fast Rinse Automatic BypassElectronics Care Of Your Water Softener Salt BridgeSalt Bridge Keeping the Water Softener Clean Iron from Resin BEDNozzle & Venturi Drain ALL Water from Softener Protect the Water Softener from FreezingProblem Cause Correction Checklist to Help YOU Save MoneyBypass Valves SpecificationsModel 38306 Timer Code S Model 39306 Timer Code S InchesOther Specifications Faceplate Service Tech InformationWiring Schematic Always Make These Initial Checks FirstProcedure for Removing Error Code from Faceplate Possible Defect CodeOther Information Troubleshooting Valve Position IndicatorsTimer PWA Replacement ModelBrine Valve Float Setting Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Assembly Rotary Valve ServiceDisassembly To Relieve PressureWater Flow Through the Softener Valve Service Cycle Fill CycleBrining and Brine Rinse Cycle Backwash Cycle Water Flow Through the Softener Valve Backwash CycleFast Rinse Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line Exploded View Parts List Water Softener CompletePart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours