Kenmore 300 Series, 300 Series Install Covers and Restart Water Heater, Restart the Water Heater

Page 17

Install Covers and Restart Water Heater

INSTALL COVERS

After installing your water softener, replace the covers. Angle the covers so the main cover clips onto the back first, then bring down in front and clip on the two (2) tabs inside the rim of the salt hole and lower the salt cover closed. See Fig. 23.

RESTART THE WATER HEATER

Turn on the gas (or electric) supply to the water heater and light the pilot.

YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE.

INSTALL COVERS

Cover (Main)

Salt Hole

Cover

FIG. 23

Questions? Call The Kenmore Water Line 1-800-426-9345

Image 17

Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerTEN Year Limited Warranty Against Leaks Facts and Figures to Keep Table of ContentsSafety Guides Parts Descriptions Unpack and Check Your CartonSmall Parts Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw in Your Pipes and Fittings Suggested Slab Foundation InstallationPIPE, FITTINGS, Other Materials Needed OUTBefore Installing Checks & Tests Read Before Beginning InstallationBypass Valve Install Plastic Bypass ValveAssemble Inlet Outlet ADAPTORS, or Plastic Bypass Valve Installing Holding Clips Install 3-Valve BypassInstalling 3 Valve Bypass and Pipes Valve BypassMove Softener Into Place Locate Water Softener and Connect PipesTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect Valve and Salt Tank DrainsConnect the Valve Drain Hose House Main Water Shutoff Valves Leak TestSingle Bypass Leak TestConnecting Transformer Water Meter Jumper WireElectrical Requirements Cold Water Pipe GroundingInstall Covers Install Covers and Restart Water HeaterInstall Covers Restart the Water HeaterSET Present Time of DAY Program The TimerProgram the Timer SET Salt Level SET Water Hardness NumberSET Regeneration Time Sanitize Your Water Softener AS Follows Sanitize The Water SoftenerSanitize the Water Softener Water Softening Salt with Iron Removing Additives Adding Salt To The Storage TankAdding Salt to the Storage Tank Check List Check List of STEP-BY-STEP Guides to InstallExtra Recharge Faceplate Timer FeaturesRecharge NOW Recharge TonightError Code Efficiency ModeTo turn this setting on Program MemorySoft Water Service and Regeneration Water Flow Through Softener in ServiceHow Your Water Softener Works Water Flow Through Softener in FillWater Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseElectronics Water Flow Through Softener Fast RinseAutomatic Bypass Salt Bridge Care Of Your Water SoftenerSalt Bridge Nozzle & Venturi Keeping the Water Softener CleanIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money Problem Cause CorrectionModel 38306 Timer Code S Model 39306 Timer Code S SpecificationsBypass Valves InchesOther Specifications Wiring Schematic Service Tech InformationFaceplate Always Make These Initial Checks FirstPossible Defect Code Procedure for Removing Error Code from FaceplateTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information ModelCycle Flow Rates Gallons PER MIN Brine Valve Float SettingManual Advance Regeneration Check Disassembly Rotary Valve ServiceAssembly To Relieve PressureBrining and Brine Rinse Cycle Water Flow Through the Softener Valve Service CycleFill Cycle Fast Rinse Cycle Water Flow Through the Softener Valve Backwash CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line Exploded View Part Number Part Description Parts ListWater Softener Complete Inlet Outlet Grounding Clamps Brine Valve Assembly Seal Key Part Number Part Description Get it fixed, at your home or ours