Craftsman 139.53664SRT2 Fasten Door Bracket, Bracket Hodzontal and vertical reinforcement

Page 24

Installation Step 11

Fasten Door Bracket

Follow instructions which apply to your door type as illustrated below or on page 25.

A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel.

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a "U"-shapedsupport. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit.

Header

Bracket

Door

Bracket

Hodzontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, aluminum, steel, doors with glass panel, etc), Figure I

(Not Provided)

Reinforcement

Vertical

Guideline

;/

Location

Carriage Bolt

Door

Bracket

uP

•Center the door bracket on the previously marked vertical guideline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket.

•Position the bracket on the face of the door within the following limits:

A)The top edge of the bracket 2"-4" below the top edge of the door.

B)The top edge of the bracket directly below any structural support across the top of the door.

•Mark and drill 5/16" left and right fastening holes. Secure the bracket as shown in Figure 1 if there is vertical reinforcement.

If your installation doesn't require vertical reinforce- ment but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2.

Lock

Washer

5/16 •

5/16"-18

Figure 2

Inside Edge of Door or

Reinforcement Board

Door Bracket

Hardware Shown Actual Size

© ©

Nut 5/16-18

Lock Washer 5/16"

IlllllllLLllllllll

Cardage Bolt

5/16"-18x2-1/2"

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents CRRFTSMIiN Start by Reviewing these Important Safety Alert Symbols MechanicalElectricaLYoull Need Tools Otherwise, the safety reverse system may not Closed PositionIt must close on the floor all the way across Work properly. See page 30. Floor or door shouldOne-P ece Door without Track One-Piece Door with TrackHardw&faSlsenlguired Carton Inventory Installation Hardware Safety Reversing Sensor Installation HardwareAssembly Section Pages 8 Assembly StepAssemble the T-rail Attach the Belt Pulley Bracket Hardware Shown Actual SizeInstall the Trolley on the T-rail Fasten the T-rail to the OpenerInstall the Belt Set Belt Tension PlaceCheck to make sure the belt is not twisted Attach the Belt Cap Retainer To attach the belt cap retainerInstallation Section Installation Step #youneed to install the header bracketPages 12 Proceed to ,One-piece door without track Jamb hardware ExampleInstall the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling DoorHardware Shown Actual SizeAttach the T-rail Header Bracket Shown Actual SizePosition the Opener Hang the Opener Opener could fall and injure someone if itIs not properly secured. Fasten the opener Install the Premium Control Console Install the Lights Lenses Install the lenses32 explains how to use the door control Install the lightsIf permanent wiring is required by your local Code, refer to the following procedureElectrical Requirements Safety Reversing System Facing the door from inside the garageInstall the Safety Reversing Sensor Sensors will face each other across the garage doorFinger tighten the lock nuts Alternate Floor MountAligning the Safety Sensors Trouble ShootingFasten Door Bracket Bracket Hodzontal and vertical reinforcementScrewsnot provided Connect Door Arm to Trolley Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Fasten the straight and curved door arm sectionsTogether to the longest possible length, with a 2 or Adjustment Section Pages 28 Adjust the UP and Down LimitsHow and When to Adjust the Limits If the door does not close completelyAdjustment Step Adjust the ForceHow and When to Adjust the Forces Test the Down close forceTest The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check AdjustmentMaintenance To reduce the risk of severeInjury or death to persons Care of Your OpenerOperation of Your Opener Operation of the Door ControlsReceiver and Remote Control Programming If you have a Premium Control ConsoleIf you do not have a Premium Control Console Having a Problem? Probable Cause and SolutionSituation Probable Cause & Solution Repair Parts Rail Assembly PartsInstallation Parts Repair Parts Opener Assembly PartsAccessories For Sectional Doors On12If you do not have Premium Control Console Index 8OO-366-PART Product Type Part Number Model Description

139.53664SRT2 specifications

The Craftsman 139.53664SRT2 is a highly regarded garage door opener that combines reliability, advanced technology, and user-friendly features. Designed for residential use, this model stands out due to its robust functionality and ease of installation, making it a popular choice among homeowners.

One of the standout features of the Craftsman 139.53664SRT2 is its powerful motor. It boasts a 1/2 horsepower motor capable of lifting standard residential garage doors with ease. This strength means reliable performance even in adverse weather conditions, ensuring that your door operates smoothly and efficiently each time.

Another key technology in this model is the Smart Control system. The Craftsman 139.53664SRT2 allows users to operate their garage door remotely, thanks to its built-in Wi-Fi connectivity. By connecting to a smartphone app, homeowners can monitor and control their garage door from anywhere, providing added convenience and security. This feature also enables users to receive alerts and notifications, ensuring they are always informed about the status of their garage door.

Security is a top priority for the Craftsman brand, and the 139.53664SRT2 features advanced security measures, including rolling code technology. This technology generates a new access code each time the remote is used, effectively preventing unauthorized access and ensuring that your garage remains secure.

The installation of the Craftsman 139.53664SRT2 is straightforward, thanks to its user-friendly design and comprehensive instructions. Many users appreciate that it can be installed as a DIY project, saving on installation costs while providing the satisfaction of completing the task themselves. The system is compatible with most existing garage door systems, making it versatile for different setups.

In terms of noise level, the Craftsman 139.53664SRT2 operates quietly, allowing for a smooth opening and closing process without disturbing the household. This feature is particularly beneficial for those with living spaces above the garage.

Overall, the Craftsman 139.53664SRT2 is a dependable garage door opener that integrates modern technology, ensuring safety, convenience, and ease of use. Its powerful motor, Wi-Fi capability, and enhanced security features make it a valuable addition to any home.
Top Page Image Contents