Craftsman 139.53664SRT2 owner manual Install the Premium Control Console

Page 18

Installation Step 6

Install the Premium Control Console

Locate the door control within sight of the door at a minimum height of 5 feet where small

children cannot reach, and away from all moving aarts of the door and door hardware.

The door control is typically attached directly to the wall. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), Console models may be mounted to a standard single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of the bell wire and connect it to the two screw terminals on

the back of the door control: white to 2, and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4" self- tapping screws (standard installation) or 6-32xl" machine screws (pre-wired installation) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. Do not overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short.

4.Connect the bell wire to the terminal screws on the opener panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

 

 

Opener

 

Bell Wire

Terminal Screws

 

 

Top

Lighted

Mounting

Push

Button

Hole

 

 

Terminal

 

 

Bottom

 

 

Mounting

 

 

Hole

 

BACK

VIEW

 

Lock

 

PREMIUM CONTROL

CONSOLE

 

::::::::::::::::::::::::::::::::::::::... .:u::::::t::::

: ::::::::::::::::::::::::::::::::::::::

 

 

::::5::::_;

:::::5::;::::_::

:::::::::::::::::::::::::::::::::::::::::::::: :::::::::::::::::::::::

":t::_:::::_:: :

-:+ :;+..:_.

....

:

_...

.+:.:,>:,:,:.;,_:+:>:<.::+::

IIITI"

Do not connect to live electrical wiring, Connect only to 24 Volt low voltage wires.

Connection to live wires or higher voltage may cause serious injury from shock, burn or electrocution.

Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death.

Install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible.

Do not allow children to operate the push button(s) or the remote control(s).

A moving garage door could injure someone under it, Activate the opener only when the

door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.

Hardware Shown Actual Size

llldlblddfillll

II mlm]>

insulated

6AB x 1-1/4" Screw

Control Console (std Installation)

Staples

Control Console (pre-wlred)

Dry Wall Anchors

Figure I

 

Figure 2

REMOVE & REPLACE

COVER

PRE-WlRED

iNSTALLATION

TOReplace,TopFirstTapsInsert • _ _•

ToRemove,TwistHere

/__ _*"

__

 

2-Conductor

 

 

Bell Wire

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CRRFTSMIiN Start by Reviewing these Important Safety Alert Symbols MechanicalElectricaLYoull Need Tools It must close on the floor all the way across Otherwise, the safety reverse system may notClosed Position Work properly. See page 30. Floor or door shouldOne-P ece Door without Track One-Piece Door with TrackHardw&faSlsenlguired Carton Inventory Installation Hardware Safety Reversing Sensor Installation HardwareAssemble the T-rail Attach the Belt Pulley Bracket Assembly Section Pages 8Assembly Step Hardware Shown Actual SizeInstall the Trolley on the T-rail Fasten the T-rail to the OpenerInstall the Belt Set Belt Tension PlaceCheck to make sure the belt is not twisted Attach the Belt Cap Retainer To attach the belt cap retainerPages 12 Installation Section Installation Step#youneed to install the header bracket Proceed to ,One-piece door without track Jamb hardware ExampleFasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall DoorHardware Shown Actual SizeAttach the T-rail Header Bracket Shown Actual SizePosition the Opener Hang the Opener Opener could fall and injure someone if itIs not properly secured. Fasten the opener Install the Premium Control Console 32 explains how to use the door control Install the Lights LensesInstall the lenses Install the lightsIf permanent wiring is required by your local Code, refer to the following procedureElectrical Requirements Safety Reversing System Facing the door from inside the garageFinger tighten the lock nuts Install the Safety Reversing SensorSensors will face each other across the garage door Alternate Floor MountAligning the Safety Sensors Trouble ShootingFasten Door Bracket Bracket Hodzontal and vertical reinforcementScrewsnot provided Connect Door Arm to Trolley Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Fasten the straight and curved door arm sectionsTogether to the longest possible length, with a 2 or How and When to Adjust the Limits Adjustment Section Pages 28Adjust the UP and Down Limits If the door does not close completelyHow and When to Adjust the Forces Adjustment StepAdjust the Force Test the Down close forceImportant safety check Test The Safety Reversing SensorTest the Safety Reverse System AdjustmentInjury or death to persons MaintenanceTo reduce the risk of severe Care of Your OpenerOperation of Your Opener Operation of the Door ControlsReceiver and Remote Control Programming If you have a Premium Control ConsoleIf you do not have a Premium Control Console Having a Problem? Probable Cause and SolutionSituation Probable Cause & Solution Repair Parts Rail Assembly PartsInstallation Parts Repair Parts Opener Assembly PartsAccessories For Sectional Doors On12If you do not have Premium Control Console Index 8OO-366-PART Product Type Part Number Model Description

139.53664SRT2 specifications

The Craftsman 139.53664SRT2 is a highly regarded garage door opener that combines reliability, advanced technology, and user-friendly features. Designed for residential use, this model stands out due to its robust functionality and ease of installation, making it a popular choice among homeowners.

One of the standout features of the Craftsman 139.53664SRT2 is its powerful motor. It boasts a 1/2 horsepower motor capable of lifting standard residential garage doors with ease. This strength means reliable performance even in adverse weather conditions, ensuring that your door operates smoothly and efficiently each time.

Another key technology in this model is the Smart Control system. The Craftsman 139.53664SRT2 allows users to operate their garage door remotely, thanks to its built-in Wi-Fi connectivity. By connecting to a smartphone app, homeowners can monitor and control their garage door from anywhere, providing added convenience and security. This feature also enables users to receive alerts and notifications, ensuring they are always informed about the status of their garage door.

Security is a top priority for the Craftsman brand, and the 139.53664SRT2 features advanced security measures, including rolling code technology. This technology generates a new access code each time the remote is used, effectively preventing unauthorized access and ensuring that your garage remains secure.

The installation of the Craftsman 139.53664SRT2 is straightforward, thanks to its user-friendly design and comprehensive instructions. Many users appreciate that it can be installed as a DIY project, saving on installation costs while providing the satisfaction of completing the task themselves. The system is compatible with most existing garage door systems, making it versatile for different setups.

In terms of noise level, the Craftsman 139.53664SRT2 operates quietly, allowing for a smooth opening and closing process without disturbing the household. This feature is particularly beneficial for those with living spaces above the garage.

Overall, the Craftsman 139.53664SRT2 is a dependable garage door opener that integrates modern technology, ensuring safety, convenience, and ease of use. Its powerful motor, Wi-Fi capability, and enhanced security features make it a valuable addition to any home.
Top Page Image Contents