Craftsman 139.53664SRT2 owner manual Receiver and Remote Control Programming

Page 33

Receiver and Remote Control Programming

Your garage door opener receiver and remote control have been pre-set at the factory. The door will open when you press the LARGE remote control push button. The code between the remote control and the

receiver changes with each use, randomly accessing over 100 billion new codes.

The 3-function remote control can also activate additional SECURITY-I- garage door openers and/or light controls.

Your SECURITY.I, opener will operate with: several SECURITY+ remote controls (with blue push buttons) utilizing up to 8 functions.

•one SECURITY+ Keyless Entry System (Model 139.53684).

Follow the instructions below to program your opener to match any additional remotes you may purchase. See Accessories on page 38.

To Add A Remote Control

If you have a Premium Control Console:

1.With the doorc/osed, press and hold a remote control push button. See Figure 1.

2.Press and hold the Light button on the door control.

3.Press and hold the door control push button.

4.After the opener light flashes, release all buttons. Test by pressing the remote push button.

If you do not have a Premium Control Console:

1.Press and holdthe selected remote control push button. See Figure 1.

2.Then press and release the SRT (learn) button on the back panel of the opener, Figure 2. The indicator light on the panel will begin to blink and the opener light will flash once.

3.Release the remote push button.

Test by pressing the remote push button.

To Erase All Remote Control Codes

Press and hold the SRT button on the opener panel

until the indicator light turns off (about 6 seconds). All remote control codes are now erased. Then follow

the steps above to re-program each remote control.

1 To comply with FCC rules, adjustment or modifications of this receiver /

and/or transmitter are prohibited, except for changing the code setting or / replacing the battery. THERE ARE NO OTHER USER SERF[CEABLE

PARTS.

injury or death. Do not allow children to operate the door push button(s) or remote control(s).

A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted.

Figure I

Select a remote control push button to operate opener

SECURITY'I"

3-Function

 

Remote Control

Figure 2

 

 

SECURITY+

 

Garage Door Opener

SRT (learn) Indicator RIGHT

Button Light PANEL

To Control the Opener Light (Premium Consoles)

With SECURITY+ remote controls, a push button can be programmed to operate the opener light without opening the door.

1.With the door closed, press and hold the remote button that you want to control the light.

2.Press and hold the Light button on the door control.

3.Press and hold the Lock button on the door control.

4.After the opener light flashes, release all buttons.

Test by pressing the remote push button. The opener light should turn on or off but the door should not move.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents CRRFTSMIiN MechanicalElectricaL Start by Reviewing these Important Safety Alert SymbolsYoull Need Tools Closed Position Otherwise, the safety reverse system may notIt must close on the floor all the way across Work properly. See page 30. Floor or door shouldOne-P ece Door without Track One-Piece Door with TrackHardw&faSlsenlguired Carton Inventory Safety Reversing Sensor Installation Hardware Installation HardwareAssembly Step Assembly Section Pages 8Assemble the T-rail Attach the Belt Pulley Bracket Hardware Shown Actual SizeFasten the T-rail to the Opener Install the Trolley on the T-railInstall the Belt Set Belt Tension PlaceCheck to make sure the belt is not twisted To attach the belt cap retainer Attach the Belt Cap Retainer#youneed to install the header bracket Installation Section Installation StepPages 12 Proceed to ,Example One-piece door without track Jamb hardwareFasten the Header Bracket to the Wall Install the Header BracketFasten the Header Bracket to the Ceiling DoorHardware Shown Actual SizeShown Actual Size Attach the T-rail Header BracketPosition the Opener Hang the Opener Opener could fall and injure someone if itIs not properly secured. Fasten the opener Install the Premium Control Console Install the lenses Install the Lights Lenses32 explains how to use the door control Install the lightsIf permanent wiring is required by your local Code, refer to the following procedureElectrical Requirements Facing the door from inside the garage Safety Reversing SystemSensors will face each other across the garage door Install the Safety Reversing SensorFinger tighten the lock nuts Alternate Floor MountTrouble Shooting Aligning the Safety SensorsBracket Hodzontal and vertical reinforcement Fasten Door BracketScrewsnot provided Hole Alignment Alternative Connect Door Arm to TrolleyAdjustment Procedures for One-Piece Doors Fasten the straight and curved door arm sectionsTogether to the longest possible length, with a 2 or Adjust the UP and Down Limits Adjustment Section Pages 28How and When to Adjust the Limits If the door does not close completelyAdjust the Force Adjustment StepHow and When to Adjust the Forces Test the Down close force Test the Safety Reverse System Test The Safety Reversing Sensor Important safety check AdjustmentTo reduce the risk of severe MaintenanceInjury or death to persons Care of Your OpenerOperation of the Door Controls Operation of Your OpenerReceiver and Remote Control Programming If you have a Premium Control ConsoleIf you do not have a Premium Control Console Having a Problem? Probable Cause and SolutionSituation Probable Cause & Solution Repair Parts Rail Assembly PartsInstallation Parts Opener Assembly Parts Repair PartsAccessories For Sectional Doors On12If you do not have Premium Control Console Index Product Type Part Number Model Description 8OO-366-PART
Top Page Image Contents