Craftsman 139.53664SRT2 Install the Header Bracket, Fasten the Header Bracket to the Wall

Page 14

Installation Step 2

Install the Header Bracket

You can attach the header bracket either to the

wall above the garage door, or to the ceiling. Follow the instructions which will work best for

your particular requirements.

Fasten the Header Bracket to the Wall

•Center the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

•Mark either set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

__ Header _

Wall

2x4

Structural Support

+,

Highest

Point ol Travel

(of Garage Door)

	Wall
• •	Mountin Holes
• • " Lag Screws	'/'

Door_

P goT _o._oa2t__ml_Ua_e)raPs__/:gtb o

Optional

Wall Mounting

Holes

Garage _

DoorHardware Shown Actual Size

Vedlcal

Center

Line

5/16"-9Xl-5/8"

Fasten the Header Bracket to the Ceiling

•Extend the vertical guideline onto the ceiling as shown.

•Center the bracket on the vertical mark, no more than 6" from the wall. Make sure the arrow is pointing toward the walt. The bracket can be mounted flush against the ceiling when clearance is minimal.

•Mark holes designated for ceiling mount only• Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes

Door

Spdng

Header

Wall

The nail hole is lot positioning only.

You must use lag screws to mount the header bracket

14

Image 14

Contents CRRFTSMIiN Start by Reviewing these Important Safety Alert Symbols MechanicalElectricaLYoull Need Tools It must close on the floor all the way across Otherwise, the safety reverse system may notClosed Position Work properly. See page 30. Floor or door shouldHardw&faSlsenlguired One-P ece Door without TrackOne-Piece Door with Track Carton Inventory Installation Hardware Safety Reversing Sensor Installation HardwareAssemble the T-rail Attach the Belt Pulley Bracket Assembly Section Pages 8Assembly Step Hardware Shown Actual SizeInstall the Trolley on the T-rail Fasten the T-rail to the OpenerCheck to make sure the belt is not twisted Install the Belt Set Belt TensionPlace Attach the Belt Cap Retainer To attach the belt cap retainerPages 12 Installation Section Installation Step#youneed to install the header bracket Proceed to ,One-piece door without track Jamb hardware ExampleFasten the Header Bracket to the Ceiling Install the Header BracketFasten the Header Bracket to the Wall DoorHardware Shown Actual SizeAttach the T-rail Header Bracket Shown Actual SizePosition the Opener Is not properly secured. Fasten the opener Hang the OpenerOpener could fall and injure someone if it Install the Premium Control Console 32 explains how to use the door control Install the Lights LensesInstall the lenses Install the lightsElectrical Requirements If permanent wiring is required by your localCode, refer to the following procedure Safety Reversing System Facing the door from inside the garageFinger tighten the lock nuts Install the Safety Reversing SensorSensors will face each other across the garage door Alternate Floor MountAligning the Safety Sensors Trouble ShootingFasten Door Bracket Bracket Hodzontal and vertical reinforcementScrewsnot provided Connect Door Arm to Trolley Hole Alignment AlternativeTogether to the longest possible length, with a 2 or Adjustment Procedures for One-Piece DoorsFasten the straight and curved door arm sections How and When to Adjust the Limits Adjustment Section Pages 28Adjust the UP and Down Limits If the door does not close completelyHow and When to Adjust the Forces Adjustment StepAdjust the Force Test the Down close forceImportant safety check Test The Safety Reversing SensorTest the Safety Reverse System AdjustmentInjury or death to persons MaintenanceTo reduce the risk of severe Care of Your OpenerOperation of Your Opener Operation of the Door ControlsIf you do not have a Premium Control Console Receiver and Remote Control ProgrammingIf you have a Premium Control Console Situation Having a Problem?Probable Cause and Solution Probable Cause & Solution Installation Parts Repair PartsRail Assembly Parts Repair Parts Opener Assembly PartsIf you do not have Premium Control Console AccessoriesFor Sectional Doors On12 Index 8OO-366-PART Product Type Part Number Model Description