Craftsman 139.3043 Install the Lights, Attach the Emergency Release Rope and Handle, 100WattMax

Page 17

INSTALLATION STEP 6

Install the Lights

1.Pressthe releasetabs on both sides of lens. Gentlyrotate lens back and downward until the lens hinge is in the fully open position. Do not removethe lens.

2.Insert an A19 incandescentor compact fluorescent light bulb (100 watt maximum), into the light socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF.

3.Reversethe procedure to close the lens.

4.If the bulbs burn out prematurely due to vibration, replacewith a garage door opener bulb. UseA19, standard neck garage door opener for replacement.

To prevent possible OVERHEATINGof the end panelor light socket:

UseONLYA19 incandescentor compact fluorescent light bulbs.

DONOTuse incandescentbulbs larger than IOOW.

DONOTuse compact fluorescent light bulbs larger than 26W (IOOW) equivalent.

DONOTuse halogen bulbs.

DONOTuse short neck or specialty light bulbs.

Compact Fluorescent --

Light Bulb

NOTE: Use only standard light bulbs. The use of short neck or speciality light bulbs may overheat the endpanel or light socket.

]_ or

Release Tab

100Watt(Max)

' Standard Light Bulb

Hinge

100Watt(Max) StandardLightBulb

Compact Fluorescent

Light Bulb

INSTALLATION STEP 7

Attach the Emergency Release Rope and Handle

1.Thread one end of the rope through the hole in the top of the red handleso "NOTICE"reads right side up as shown, Secure with an overhand knot at least1" (2.5 cm) from the end of the ropeto prevent slipping,

2.Thread the other end of the rope through the hole in the release arm of the outer trolley.

3.Adjustrope lengthso the handle is 6 feet (1.83 m) above the floor, Ensurethat the rope and handle clear the tops of all vehicles to avoid entanglement,Secure with an overhand knot,

NOTE:If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

To prevent possible SERIOUSINJURYor DEATHfrom a falling garagedoor:

If possible, use emergency releasehandleto disengage trolley ONLYwhen garagedoor is CLOSED.Weak or broken springs or unbalanceddoor could result in an open door falling rapidly and/or unexpectedly.

NEVERuse emergency releasehandle unless garagedoorway is clear of persons and obstructions.

NEVERuse handle to pull door open or closed. If rope knot becomes untied, you could fall.

Trolley

Trolley

Release Arm 1

 

 

Overhand

Emergency

_

Knot

Release Handle

_

 

17

Image 17
Contents Garagedooropener Abridorde Puertadecochera Safety SymbolReviewand Signal WordReview Warranty41-42 BackCoverOne-Piece Door Preparingyourgarage doorSectionaldoorinstallation Sectionaldoor InstallationAccessDoor PlanningONE-PIECEDOORWITH Track ONE-PIECEDOOR InstallationsONE-PIECEDOORWITHOUT Track With screws3 CartonInventoryInstallationhardware AssemblyhardwareHardwareInventory NutFasten the Rail to the Motor Unit Assemble the Rail and Install the TrolleyInner Trolley Rail TOPInstall the Idler Pulley Install the Belt Set the Tensionand Install the SprocketCover ImportantinstallationinstructionsOne-piecedoor withouttrack Determine the HeaderBracketLocationHardware Wall Headerbracketinstallation Install the Header BracketCeilingheaderbracketinstallation SpringHeaderWall HeaderBracket IdlerPulley Header0 Attach the Raft to the Header BracketONE-PIECEDOORWITHOUTTRACK Positionthe OpenerSectionaldooror ONE-PIECEDOORWITH Track Finished Ceiling Hang the OpenerOrts Attach the Emergency Release Rope and Handle Install the Lights100WattMax WattMax StandardLightBulbFasten the Door Bracket Metal, insulated or light weight factoryreinforced doorsSectionaldoors WoodDoorsBracket Self-ThreadingScrew 1/4-14x5/8Sectionaldoorsonly Connect Door Arm to TrolleyHole alignment alternative Straight DoorArmAttach the Warning Labels ConnectDoorArm to Tro//eyOuter RingWirethe DOORCONTROLFIGURE2 Install the Door ControlIntroduction Connected to the garage door opener in a later stepInstall the Door Control Install The ProtectorSystemWirethe Doorcontrolto the Garagedooropener Importantinformationaboutthe Safetyreversing SensorGarage door trackinstallation preferred Installingthe BracketsWaft installation Figures2 Floor installation FigureInsta// TheProtectorSystem Option B Pre-Wired /nsta//ationMounting Connectto GaragedooropenerPermanentwiring Optionb Aligningthe SafetyReversingSensorsWireNuts Electrical RequirementsIf the Amberled Onthe Sendingsensoris not Glowing Aligning the Safety Reversing SensorsIf the Greenled on the Receivingsensoris not Glowing ProgrammingbuttonsProgramthe Travel IMPORTANTNOTEFor one-piece door installations refer toAdjust Testthe SafetyReversalSystemImportantsafetycheck Test The ProtectorSysterInstall the Battery Testthe BatteryBatterystatusled Greenled Chargethe BatteryFeatures Door Control Features Smart ControlPane/SetupSettings Menu NavigationTo Erase the Memory ProgrammingENTERbutton Eraseall Remotecontrolsand KeylessentriesCareof YourOpener To Openthe Door ManuallyEverymonth EveryyearFlash 2 Flashes DiagnosticchartFlash 3 Flashes Flash 4 FlashesArrow Flashes Diagnostic UP Down4FLASHES Flashes Flashes 6 FlashesDescription Rail Assembly Parts Installation PartsKEY Part Motor Unit Assembly Parts41B135 Line cord 41A7630Installingopener in garagewith low headroom clearance Available only throughSears Parts & ServiceForSectionalDoorsOnly41A7569 139.53728 139.53729Page Page Revisi6n de lossimbo/osy trminosde seguridad Puertade unasola pieza Preparaci6nde la puerta de su cocheraHerramientasnecesarias Instalacioncon Unapuertaseccional Planificaci6nInstalaciincon Unapuertaseccional EN Posicion CerradaInstalacioncon Puertasde Unasolapieza Planificaci6n continUaPuertade UNA Solapiezasin Carril Puertade UnapiezaconcarrilCubiertadela banda Inventario de la caia de cartdnContornillos3 SecciOndelantera delrielcabezalTornilleriay Piezasparalainstalacion Inventario de piezasTornilleriay Piezasparaelmontaje Fije e/tie/a la unidadde/motor Monte e/fie/e insta/e e/tro/ePartesuperior Estaspiezasse Muestranen SU TamaiorealEstas Piezasse Iviuestranen SU Taiviaioreal Nstale la po/ea IocaTrole Destornillador Orificiode paro deltrole Conector deltrole Nsta/e /a bandaConranura Estas Piezasse Muestran EN SU Tamaio NormalEstas Piezasse Muestran EN SU Tamaionormal InstruccionesimportantesparalainstalacionAccesoriosde montaje Determine d6nde va a insta/ar la mnsulade/cabezaInstalaciinde LA Mensuladel Cabezalen LA Pared Delantera Insta/e /a mnsu/a de/cabezaInstalaciinde LA Mensuladel Cabezalen Elcieloraso Estas Piezasse Muestran EN SU TamaiorealOrificiode montaje Co/oquee/fie/en la mnsula de/cabezaPuertade Unasolapiezasin Carril Coloque el abridor en posici6nPUERTASECCIONAL0 Puertade Unasolapiezacon Carril Estas Piezas SE Muestran EN SU Tamaioreal Cuelgueel abridorColoquela Manija y la Cuerdade Emergencia Instale /as lucesPuertas de madera Fije la m6nsuladela puertaPuertasseccionales Puertasde Unasolapieza Fije /a mnsu/a de la puerta contin#a16-18x7/8 Conecteel brazo de la puerta al troleSI3LOPARA Puertasseccionales Correcto IncorrectoColocar/as etiquetas de advertencia Conectee/brazo de/a puerta a/tro/e contin#aTodaslas Puertasde Unasolapieza TroleIntroduccion Instalar el controlde la puertaAlambrede Controlde LA PUERTAFIGURA2 Montar Elcontrolde LA PUERTAFIGURA3TENDERLOSCABLESDESDEELCONTROLHASTAELABRE-PUERTA FIGURA4 Instalar e/contro/de/a puerta continUaInstale la ProtectorSystem+ Instalacionde LAS Minsulas Instale la ProtectorSystem contin#aInstalaci6n en la pared Figuras2 y Instalacifin en el piso FiguraMontaje Insta/e /a ProtectorSystem contin#aOpci#n a Instalaci#nsin cables preinstalados Opci#n B Concables preinstaladosAlineaciCnde los sensoresde reversa de seguridad Requisitospara /a insta/aciCne/ ctricaCorrectoincorrecto Conexioncon CableadopermanenteIntroducci6n Ineaci6n de/os sensores de reversa de seguridad continUaProgramaci6nde/desp/azamiento Prueba la ProtectorSystem Pruebe e/sistema de seguridadde reversaPrueba AjustePrueba de la bateria Instale la bateriaFunciones Contro/de /a puerta Funcionescontin#aPu/sadordebarra Paraabrir o cerrarla puertautilizarelpulsadorde barraFunciones Configuraci6nde/a Smart Contro/PaneBorrartodoslos Dispositivos Para borrar la memoriaProgramaciCn Mantenimiento de su abridor de puerta de cochera C6moabrir la puerta manualmenteUna vez al mes Una vez al afioSensoresde Destello 4 Destellos 51DESTELLO 5 DestellosTablade Diagnistico SolucionDestellos 1DESTELLO Tablade DiagnosticoS61opara puertas seccionales OpcionalesParalainstalaci6ndelsensordeSeguridadenlaparedo enelpiso MY-HOME

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.