Craftsman Troubleshooting Garage Door Opener Error Codes
Page 36

TROUBLESHOOTING

DIAGNOSTICCHART

Your garagedoor opener is programmed with self-diagnostic capabilities. The UP and DOWNarrows on the garage door openerflash the diagnostic codes.

DIAGNOSTIC UPDOWN

CODE ARROW ARROW

1-11 FLASH 1 FLASH

SYMPTOM

CAUSE

RESOLUTION

The garagedoor

Safety sensors are

Inspect sensor wires for a disconnected or

opener will not

notinstalled,

cut wire(s). If the sending sensor with the

close and the

connected,or wires

amber LEDis NOTlit, check the wire and

light(s) willflash

may be cut

connections for that sensor. If sending

 

 

sensor LED is lit, check the wire

 

 

connections leading to the receiving

 

 

sensor (green LED). Reattachwire or

 

 

replacewire (22 gaugewire) as needed. If

 

 

pre-wired home, check the splices. See

 

 

page24 for installation. Closethe garage

 

 

door using the remote control or the door

 

 

control.

1-21 FLASH 2 FLASHES

The garagedoor

Safety sensor wire

opener will not

shorted or reversed

close and the

 

light(s) willflash

 

Inspect sensor wire for incorrect wiring or a pinched wire. If the sending sensor (amber LED) is not lit, check the wire leadingto and from that sensor. Check staple points. If sending sensor LED is lit, check the wire leadingto the receiving sensor (green LED). Reattachwire or replacewire (22 gaugewire) as needed. If pre-wired home, check the splices. See page24 for installation. Closethe garage door using the remote control or the door control.

1-31 FLASH 3 FLASHES

Wall-mounted door

The wires for the

Inspect door control wires for a short

control will not

door control are

(staple in wire), replacewire (22 gauge

function

shorted or the door

wire) as needed.After installing new door

 

control is faulty

control wires, if door control still does not

 

 

operate garagedoor opener, replacethe

 

 

door control.

1-41 FLASH 4 FLASHES

The garagedoor

Misaligned or

opener will not

obstructed safe_

close the doorand

sensors

thelight(s)flash

 

Realignthe receiving sensor (green LED) by ensuring the LED is steady and not flickering. A flicker of the safety sensor LEDindicates a misalignment. Make sure nothing is hanging or mounted on the door interrupting the sensor'spath while

closing. Closethe garage door using the remote control or the door control.

The garagedoor

Bad logic board

Replacethe logic board.

opener clicks but no

 

 

movement

 

 

1-5

1 FLASH

5 FLASHES

The opener runs

Communication

approximately 6-8"

error to travel

 

 

 

 

 

 

and stops and/or

module

 

 

 

reverses

 

Disconnect all power, remove cover, and locatethe travel module. Ensurethe wires

for travel module are connected, if wires

areconnected, then replacethe travel module.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Garagedooropener Abridorde Puertadecochera Warranty Safety SymbolReviewand Signal WordReview41-42 BackCoverPreparingyourgarage door One-Piece DoorSectionaldoor Installation SectionaldoorinstallationAccessDoor PlanningONE-PIECEDOOR Installations ONE-PIECEDOORWITHOUT TrackONE-PIECEDOORWITH Track CartonInventory With screws3Assemblyhardware InstallationhardwareHardwareInventory NutAssemble the Rail and Install the Trolley Fasten the Rail to the Motor UnitInner Trolley Rail TOPInstall the Idler Pulley Install the Belt Importantinstallationinstructions Set the Tensionand Install the SprocketCoverDetermine the HeaderBracketLocation HardwareOne-piecedoor withouttrack Install the Header Bracket Wall HeaderbracketinstallationCeilingheaderbracketinstallation SpringAttach the Raft to the Header Bracket HeaderWall HeaderBracket IdlerPulley Header0Positionthe Opener Sectionaldooror ONE-PIECEDOORWITH TrackONE-PIECEDOORWITHOUTTRACK Hang the Opener OrtsFinished Ceiling Install the Lights Attach the Emergency Release Rope and Handle100WattMax WattMax StandardLightBulbMetal, insulated or light weight factoryreinforced doors Fasten the Door BracketSectionaldoors WoodDoorsSelf-ThreadingScrew 1/4-14x5/8 BracketConnect Door Arm to Trolley SectionaldoorsonlyHole alignment alternative Straight DoorArmConnectDoorArm to Tro//ey Attach the Warning LabelsOuter RingInstall the Door Control Wirethe DOORCONTROLFIGURE2Introduction Connected to the garage door opener in a later stepInstall The ProtectorSystem Install the Door ControlWirethe Doorcontrolto the Garagedooropener Importantinformationaboutthe Safetyreversing SensorInstallingthe Brackets Garage door trackinstallation preferredWaft installation Figures2 Floor installation FigureOption B Pre-Wired /nsta//ation Insta// TheProtectorSystemMounting Connectto GaragedooropenerAligningthe SafetyReversingSensors Permanentwiring OptionbWireNuts Electrical RequirementsAligning the Safety Reversing Sensors If the Amberled Onthe Sendingsensoris not GlowingIf the Greenled on the Receivingsensoris not Glowing ProgrammingbuttonsIMPORTANTNOTEFor one-piece door installations refer to Programthe TravelTestthe SafetyReversalSystem AdjustImportantsafetycheck Test The ProtectorSysterTestthe Battery Install the BatteryBatterystatusled Greenled Chargethe BatteryFeatures Door Control Smart ControlPane/Setup FeaturesSettings Menu NavigationProgramming To Erase the MemoryENTERbutton Eraseall Remotecontrolsand KeylessentriesTo Openthe Door Manually Careof YourOpenerEverymonth EveryyearDiagnosticchart Flash 2 FlashesFlash 3 Flashes Flash 4 FlashesDiagnostic UP Down Arrow Flashes4FLASHES Flashes Flashes 6 FlashesRail Assembly Parts Installation Parts DescriptionMotor Unit Assembly Parts KEY Part41B135 Line cord 41A7630Available only throughSears Parts & Service Installingopener in garagewith low headroom clearanceForSectionalDoorsOnly41A7569 139.53728 139.53729Page Page Revisi6n de lossimbo/osy trminosde seguridad Preparaci6nde la puerta de su cochera HerramientasnecesariasPuertade unasola pieza Planificaci6n Instalacioncon UnapuertaseccionalInstalaciincon Unapuertaseccional EN Posicion CerradaPlanificaci6n continUa Instalacioncon Puertasde UnasolapiezaPuertade UNA Solapiezasin Carril Puertade UnapiezaconcarrilInventario de la caia de cartdn Cubiertadela bandaContornillos3 SecciOndelantera delrielcabezalInventario de piezas Tornilleriay PiezasparaelmontajeTornilleriay Piezasparalainstalacion Monte e/fie/e insta/e e/tro/e Fije e/tie/a la unidadde/motorPartesuperior Estaspiezasse Muestranen SU TamaiorealNstale la po/ea Ioca Trole Destornillador Orificiode paro deltroleEstas Piezasse Iviuestranen SU Taiviaioreal Nsta/e /a banda Conector deltroleConranura Estas Piezasse Muestran EN SU Tamaio NormalInstruccionesimportantesparalainstalacion Estas Piezasse Muestran EN SU TamaionormalDetermine d6nde va a insta/ar la mnsulade/cabeza Accesoriosde montajeInsta/e /a mnsu/a de/cabeza Instalaciinde LA Mensuladel Cabezalen LA Pared DelanteraInstalaciinde LA Mensuladel Cabezalen Elcieloraso Estas Piezasse Muestran EN SU TamaiorealCo/oquee/fie/en la mnsula de/cabeza Orificiode montajeColoque el abridor en posici6n PUERTASECCIONAL0 Puertade Unasolapiezacon CarrilPuertade Unasolapiezasin Carril Cuelgueel abridor Estas Piezas SE Muestran EN SU TamaiorealInstale /as luces Coloquela Manija y la Cuerdade EmergenciaFije la m6nsuladela puerta PuertasseccionalesPuertas de madera Fije /a mnsu/a de la puerta contin#a Puertasde UnasolapiezaConecteel brazo de la puerta al trole 16-18x7/8SI3LOPARA Puertasseccionales Correcto IncorrectoConectee/brazo de/a puerta a/tro/e contin#a Colocar/as etiquetas de advertenciaTodaslas Puertasde Unasolapieza TroleInstalar el controlde la puerta IntroduccionAlambrede Controlde LA PUERTAFIGURA2 Montar Elcontrolde LA PUERTAFIGURA3Instalar e/contro/de/a puerta continUa Instale la ProtectorSystem+TENDERLOSCABLESDESDEELCONTROLHASTAELABRE-PUERTA FIGURA4 Instale la ProtectorSystem contin#a Instalacionde LAS MinsulasInstalaci6n en la pared Figuras2 y Instalacifin en el piso FiguraInsta/e /a ProtectorSystem contin#a MontajeOpci#n a Instalaci#nsin cables preinstalados Opci#n B Concables preinstaladosRequisitospara /a insta/aciCne/ ctrica AlineaciCnde los sensoresde reversa de seguridadCorrectoincorrecto Conexioncon CableadopermanenteIneaci6n de/os sensores de reversa de seguridad continUa Introducci6nProgramaci6nde/desp/azamiento Pruebe e/sistema de seguridadde reversa Prueba la ProtectorSystemPrueba AjusteInstale la bateria Prueba de la bateriaFunciones Funcionescontin#a Contro/de /a puertaPu/sadordebarra Paraabrir o cerrarla puertautilizarelpulsadorde barraConfiguraci6nde/a Smart Contro/Pane FuncionesPara borrar la memoria ProgramaciCnBorrartodoslos Dispositivos C6moabrir la puerta manualmente Mantenimiento de su abridor de puerta de cocheraUna vez al mes Una vez al afioDestello 4 Destellos 51DESTELLO 5 Destellos SensoresdeTablade Diagnistico SolucionTablade Diagnostico Destellos 1DESTELLOOpcionalesParalainstalaci6ndelsensorde Seguridadenlaparedo enelpisoS61opara puertas seccionales MY-HOME

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.
Top Page Image Contents