Install The ProtectorSystem | Craftsman 139.3043 specs

Install the Door Control (Continued)

WIRETHE DOORCONTROLTO THE GARAGEDOOROPENER

(FIGURE4)

Figure4DoorControlConnections

Pre-wired installations:When wiring the door control to the garage door opener makesure you use the same wires that are connected to the door control.

1.Run the white and red/white wire from the door control to the garagedoor opener. Attach the wire to the wall and ceiling with the staples (not applicable for gang box or pre-wired installations). Do not piercethe wire with the staple as this may

cause a short or an open circuit.	Strip wire 7/16" (11 mm)

2.Strip 7/16 inch (11 mm) of insulation from the other end of the wire nearthe garage door opener.

3.Connect the wire to the red and white terminals on the garage

door opener.	ro insert or release wire, push
	ro insert or release wire, push
	in tab with screwdriver tip

INSTALLATION STEP 12

Install The ProtectorSystem®

IMPORTANTINFORMATIONABOUTTHE SAFETYREVERSING SENSOR

The safety reversing sensor must be connected and aligned correctly before the garagedoor opener will move in the down direction.

The sending sensor (with an amber LED)transmits an invisible light beam to the receiving sensor (with a green LED). If an obstruction breaksthe light beam while the door is closing, the door will stop and reverseto the full open position, and the garage door opener lights will flash 10 times.

NOTE:For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. Thesleep mode shuts the garage door opener down until activated. The sleep mode is sequenced with the garage door opener light bulb; as the light bulb turns off the sensor LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will light. The garage door opener will not go into the sleep mode until the garage door opener has completed 5 cycles upon power up.

When installing the safety

ing sensors check the following:

	Safety Reversing Sensor	Invisible Light Beam
	6" (15 cm) max. above floor
		Protection Area

Facing the doorfrom inside the garage

Besure power is NOTconnected to the garagedoor opener BEFOREinstalling the safety reversing sensor.

To prevent SERIOUSINJURY or DEATHfrom a closing garage door:

•Correctly connect and align the safety reversingsensor. This required safety device MUST NOTbe disabled.

•Install the safety reversing sensor so beam is NO HIGHER than 6" (15 cm) above garagefloor.

•Sensors are installed inside the garage,one on either side of the door.

•Sensors are facing each other with the lensesaligned and the receivingsensor lens does not receivedirect sunlight.

•Sensors are no more than 6 inches (15 cm) above the floor and the light beam is unobstructed.

Safety Reversing Sensor

6" (15 cm) max. above floor

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.