Craftsman 139.3043 Instal/The ProtectorSystem, Installingthe Brackets, Waft installation Figures2

Page 24

Instal/The ProtectorSystem® (Continued)

INSTALLINGTHE BRACKETS

Be sure power to the opener is disconnected.Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows.

Garage door trackinstallation (preferred):

•Slip the curved arms over the rounded edge of each door track, with the curved arms facing the door. Snap into place against the side of the track. It should lie flush, with the lip hugging the back edge of the track, as shown in Figure 1.

If your door track will not support the bracket securely,wall installation is recommended.

Waft installation (Figures2 & 3):

•Placethe bracket against the wall with curved arms facing the door. Besure there is enough clearancefor the sensor beam to be unobstructed.

•If additional depth is needed,an extension bracket (see Accessories) or wood blocks can be used.

•Usebracket mounting holes as a template to locate and drill (2) 3/16" diameter pilot holes on the wall at each side of the door, no higher than 6" (15 cm) above the floor.

•Attach brackets to wall with lag screws (not provided).

•If using extension bracketsor wood blocks, adjust right and left assembliesto the same distance out from the mounting surface. Make sure all door hardware obstructions are cleared.

Floor installation (Figure 4):

•Usewood blocks or extension brackets (see Accessories) to elevatesensor bracketsso the lenseswill be no higher than 6" (15 cm) abovethe floor.

•Carefully measureand place right and left assembliesat the same distance out from the wall. Besure all door hardware obstructions are cleared.

•Fastento the floor with concrete anchors as shown.

HARDWARESHOWN ACTUALSIZE

Carriage Bolt

Wing Nut

Staples

1/4"-20xl/2"

1/4"-20

 

Figure I DOORTRACK MOUNT (RIGHT SIDE)

iDoor

\ Track

 

,/

Lip

Indicator

 

Light

Figure2 WALL MOUNT (RIGHT SIDE)

FastenWood Block to Wall with

Screws (not provided)

Indicator

Light Safety

Reversing

Sensor

Bracket

Lag Screws

_ (not provided)

Lens ...... '_

Figure3 WALL MOUNT (RIGHT SIDE)

Extension Bracket

Accessories)

(Provided with Extension Bracket)

 

 

Safety

(Provided with

 

Reversing

 

Sensor

Extension Bracket) _'"

 

 

Bracket

%7"

 

 

Lens

Indicator

 

 

 

 

Light

Figure4FLOORMOUNT (RIGHT SIDE)

i ttach with Concrete Anchors

; (not provided)

Indicator

Light

Reversing

Sensor

Bracket

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Garagedooropener Abridorde Puertadecochera Warranty Safety SymbolReviewand Signal WordReview41-42 BackCoverPreparingyourgarage door One-Piece DoorSectionaldoor Installation SectionaldoorinstallationAccessDoor PlanningONE-PIECEDOOR Installations ONE-PIECEDOORWITHOUT TrackONE-PIECEDOORWITH Track CartonInventory With screws3Assemblyhardware InstallationhardwareHardwareInventory NutAssemble the Rail and Install the Trolley Fasten the Rail to the Motor UnitInner Trolley Rail TOPInstall the Idler Pulley Install the Belt Importantinstallationinstructions Set the Tensionand Install the SprocketCoverDetermine the HeaderBracketLocation HardwareOne-piecedoor withouttrack Install the Header Bracket Wall HeaderbracketinstallationCeilingheaderbracketinstallation SpringAttach the Raft to the Header Bracket HeaderWall HeaderBracket IdlerPulley Header0Positionthe Opener Sectionaldooror ONE-PIECEDOORWITH TrackONE-PIECEDOORWITHOUTTRACK Hang the Opener OrtsFinished Ceiling Install the Lights Attach the Emergency Release Rope and Handle100WattMax WattMax StandardLightBulbMetal, insulated or light weight factoryreinforced doors Fasten the Door BracketSectionaldoors WoodDoorsSelf-ThreadingScrew 1/4-14x5/8 BracketConnect Door Arm to Trolley SectionaldoorsonlyHole alignment alternative Straight DoorArmConnectDoorArm to Tro//ey Attach the Warning LabelsOuter RingInstall the Door Control Wirethe DOORCONTROLFIGURE2Introduction Connected to the garage door opener in a later stepInstall The ProtectorSystem Install the Door ControlWirethe Doorcontrolto the Garagedooropener Importantinformationaboutthe Safetyreversing SensorInstallingthe Brackets Garage door trackinstallation preferredWaft installation Figures2 Floor installation FigureOption B Pre-Wired /nsta//ation Insta// TheProtectorSystemMounting Connectto GaragedooropenerAligningthe SafetyReversingSensors Permanentwiring OptionbWireNuts Electrical RequirementsAligning the Safety Reversing Sensors If the Amberled Onthe Sendingsensoris not GlowingIf the Greenled on the Receivingsensoris not Glowing ProgrammingbuttonsIMPORTANTNOTEFor one-piece door installations refer to Programthe TravelTestthe SafetyReversalSystem AdjustImportantsafetycheck Test The ProtectorSysterTestthe Battery Install the BatteryBatterystatusled Greenled Chargethe BatteryFeatures Door Control Smart ControlPane/Setup FeaturesSettings Menu NavigationProgramming To Erase the MemoryENTERbutton Eraseall Remotecontrolsand KeylessentriesTo Openthe Door Manually Careof YourOpenerEverymonth EveryyearDiagnosticchart Flash 2 FlashesFlash 3 Flashes Flash 4 FlashesDiagnostic UP Down Arrow Flashes4FLASHES Flashes Flashes 6 FlashesRail Assembly Parts Installation Parts DescriptionMotor Unit Assembly Parts KEY Part41B135 Line cord 41A7630Available only throughSears Parts & Service Installingopener in garagewith low headroom clearanceForSectionalDoorsOnly41A7569 139.53728 139.53729Page Page Revisi6n de lossimbo/osy trminosde seguridad Preparaci6nde la puerta de su cochera HerramientasnecesariasPuertade unasola pieza Planificaci6n Instalacioncon UnapuertaseccionalInstalaciincon Unapuertaseccional EN Posicion CerradaPlanificaci6n continUa Instalacioncon Puertasde UnasolapiezaPuertade UNA Solapiezasin Carril Puertade UnapiezaconcarrilInventario de la caia de cartdn Cubiertadela bandaContornillos3 SecciOndelantera delrielcabezalInventario de piezas Tornilleriay PiezasparaelmontajeTornilleriay Piezasparalainstalacion Monte e/fie/e insta/e e/tro/e Fije e/tie/a la unidadde/motorPartesuperior Estaspiezasse Muestranen SU TamaiorealNstale la po/ea Ioca Trole Destornillador Orificiode paro deltroleEstas Piezasse Iviuestranen SU Taiviaioreal Nsta/e /a banda Conector deltroleConranura Estas Piezasse Muestran EN SU Tamaio NormalInstruccionesimportantesparalainstalacion Estas Piezasse Muestran EN SU TamaionormalDetermine d6nde va a insta/ar la mnsulade/cabeza Accesoriosde montajeInsta/e /a mnsu/a de/cabeza Instalaciinde LA Mensuladel Cabezalen LA Pared DelanteraInstalaciinde LA Mensuladel Cabezalen Elcieloraso Estas Piezasse Muestran EN SU TamaiorealCo/oquee/fie/en la mnsula de/cabeza Orificiode montajeColoque el abridor en posici6n PUERTASECCIONAL0 Puertade Unasolapiezacon CarrilPuertade Unasolapiezasin Carril Cuelgueel abridor Estas Piezas SE Muestran EN SU TamaiorealInstale /as luces Coloquela Manija y la Cuerdade EmergenciaFije la m6nsuladela puerta PuertasseccionalesPuertas de madera Fije /a mnsu/a de la puerta contin#a Puertasde UnasolapiezaConecteel brazo de la puerta al trole 16-18x7/8SI3LOPARA Puertasseccionales Correcto IncorrectoConectee/brazo de/a puerta a/tro/e contin#a Colocar/as etiquetas de advertenciaTodaslas Puertasde Unasolapieza TroleInstalar el controlde la puerta IntroduccionAlambrede Controlde LA PUERTAFIGURA2 Montar Elcontrolde LA PUERTAFIGURA3Instalar e/contro/de/a puerta continUa Instale la ProtectorSystem+TENDERLOSCABLESDESDEELCONTROLHASTAELABRE-PUERTA FIGURA4 Instale la ProtectorSystem contin#a Instalacionde LAS MinsulasInstalaci6n en la pared Figuras2 y Instalacifin en el piso FiguraInsta/e /a ProtectorSystem contin#a MontajeOpci#n a Instalaci#nsin cables preinstalados Opci#n B Concables preinstaladosRequisitospara /a insta/aciCne/ ctrica AlineaciCnde los sensoresde reversa de seguridadCorrectoincorrecto Conexioncon CableadopermanenteIneaci6n de/os sensores de reversa de seguridad continUa Introducci6nProgramaci6nde/desp/azamiento Pruebe e/sistema de seguridadde reversa Prueba la ProtectorSystemPrueba AjusteInstale la bateria Prueba de la bateriaFunciones Funcionescontin#a Contro/de /a puertaPu/sadordebarra Paraabrir o cerrarla puertautilizarelpulsadorde barraConfiguraci6nde/a Smart Contro/Pane FuncionesPara borrar la memoria ProgramaciCnBorrartodoslos Dispositivos C6moabrir la puerta manualmente Mantenimiento de su abridor de puerta de cocheraUna vez al mes Una vez al afioDestello 4 Destellos 51DESTELLO 5 Destellos SensoresdeTablade Diagnistico SolucionTablade Diagnostico Destellos 1DESTELLOOpcionalesParalainstalaci6ndelsensorde Seguridadenlaparedo enelpisoS61opara puertas seccionales MY-HOME

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.
Top Page Image Contents