Craftsman 139.3043 Testthe Battery, Install the Battery, Batterystatusled Greenled, Orangeled

Page 30

BATTERY BACKUP

install the Battery

1.Unplug the garagedoor opener.

2.Openthe light lens on the right side panel of the garagedoor opener. Usea Phillips head screwdriver to remove the battery coveron the garagedoor opener.

3.Partially insertthe battery into the battery compartmentwith the terminals facing out.

4.Connect red (+) and black (-) wires from the garagedoor opener to the corresponding terminals on the battery.

5.Verify the battery wires are seated in the channeland replace the battery cover.

& Plug in the garage door opener.

7.Wait for the green Battery Status LEDto start flashing before proceeding to test the battery.

To reduce the risk of FIREor INJURYto persons:

•DisconnectALL electric and battery power BEFORE performing ANY service or maintenance.

•UseONLYCraftsman part #41B822 for replacement battery.

•DONOTdispose of battery in fire. Battery may explode. Checkwith local codes for disposal instructions.

ALWAYSwear protective gloves and eye protection when changing the battery or working around the battery compartment.

Channel

Testthe Battery

1.Unplug the garagedoor opener. The battery status LEDwill either glow solid orange indicating opener is operating on battery power or will flash indicating low battery power. NOTE: Make sure the garagedoor opener is unplugged.

2.Openand close the door using the remote control or door control. The garagedoor opener may run slower if the battery is not fully charged. The battery will take 24 hours to fully charge.

3.Plug in the garage door opener. Verify the battery status LED is flashing green, indicating the battery is charging.

BATTERYSTATUSLED

NOTE: TheBattery Status LEDis most visible with the garage door opener light off. Battery does not have to be fully charged to operate the garage door opener.

GREENLED:

All systems are normal.

•A solid green LED light indicates the battery is fully charged.

•A flashing green LED indicates the battery is being charged.

ORANGELED:

The garage door opener has lost power and is in battery backup mode.

•A solid orange LED with beep, sounding approximately every 2 seconds, indicates the garage door opener is operating on battery power.

•A flashing orange LEDwith beep,sounding every 30 seconds, indicates the battery is low.

RED LED:

The garage door opener's12V battery needsto be replaced.

•A solid red LEDwith beep, sounding every 30 seconds, indicates the 12V battery will no longer hold a charge and needs to be replaced. Pleasecall for replacement battery to allow your system to operate during a power outage.

Battery

attery Cover

Status LED

@

@

CHARGETHE BATTERY

The battery will take 24 hours to fully charge. A fully charged battery supplies 12 Vdc to the garage door opener for one to two days of normal operation during an electrical power outage. Once the battery voltage drops too low, the battery will no longer operate. After the electrical power has been restored, the battery will rechargewithin 24 hours. The battery will last 3 to 5 years with normal usage. To obtain maximum battery life and prevent damage,disconnect the battery when the garagedoor opener is unplugged for an extended period of time.

NOTE:Door operation may be fimited until the battery is fully charged. Thegarage door opener lights will not turn on during battery backup mode.

3O

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Garagedooropener Abridorde Puertadecochera 41-42 WarrantySafety SymbolReviewand Signal WordReview BackCoverPreparingyourgarage door One-Piece DoorAccessDoor Sectionaldoor InstallationSectionaldoorinstallation PlanningONE-PIECEDOOR Installations ONE-PIECEDOORWITHOUT TrackONE-PIECEDOORWITH Track CartonInventory With screws3HardwareInventory AssemblyhardwareInstallationhardware NutInner Trolley Assemble the Rail and Install the TrolleyFasten the Rail to the Motor Unit Rail TOPInstall the Idler Pulley Install the Belt Importantinstallationinstructions Set the Tensionand Install the SprocketCoverDetermine the HeaderBracketLocation HardwareOne-piecedoor withouttrack Ceilingheaderbracketinstallation Install the Header BracketWall Headerbracketinstallation SpringAttach the Raft to the Header Bracket HeaderWall HeaderBracket IdlerPulley Header0Positionthe Opener Sectionaldooror ONE-PIECEDOORWITH TrackONE-PIECEDOORWITHOUTTRACK Hang the Opener OrtsFinished Ceiling 100WattMax Install the LightsAttach the Emergency Release Rope and Handle WattMax StandardLightBulbSectionaldoors Metal, insulated or light weight factoryreinforced doorsFasten the Door Bracket WoodDoorsSelf-ThreadingScrew 1/4-14x5/8 BracketHole alignment alternative Connect Door Arm to TrolleySectionaldoorsonly Straight DoorArmOuter ConnectDoorArm to Tro//eyAttach the Warning Labels RingIntroduction Install the Door ControlWirethe DOORCONTROLFIGURE2 Connected to the garage door opener in a later stepWirethe Doorcontrolto the Garagedooropener Install The ProtectorSystemInstall the Door Control Importantinformationaboutthe Safetyreversing SensorWaft installation Figures2 Installingthe BracketsGarage door trackinstallation preferred Floor installation FigureMounting Option B Pre-Wired /nsta//ationInsta// TheProtectorSystem Connectto GaragedooropenerWireNuts Aligningthe SafetyReversingSensorsPermanentwiring Optionb Electrical RequirementsIf the Greenled on the Receivingsensoris not Glowing Aligning the Safety Reversing SensorsIf the Amberled Onthe Sendingsensoris not Glowing ProgrammingbuttonsIMPORTANTNOTEFor one-piece door installations refer to Programthe TravelImportantsafetycheck Testthe SafetyReversalSystemAdjust Test The ProtectorSysterBatterystatusled Greenled Testthe BatteryInstall the Battery Chargethe BatteryFeatures Door Control Settings Smart ControlPane/SetupFeatures Menu NavigationENTERbutton ProgrammingTo Erase the Memory Eraseall Remotecontrolsand KeylessentriesEverymonth To Openthe Door ManuallyCareof YourOpener EveryyearFlash 3 Flashes DiagnosticchartFlash 2 Flashes Flash 4 Flashes4FLASHES Flashes Diagnostic UP DownArrow Flashes Flashes 6 FlashesRail Assembly Parts Installation Parts Description41B135 Line cord Motor Unit Assembly PartsKEY Part 41A7630ForSectionalDoorsOnly41A7569 Available only throughSears Parts & ServiceInstallingopener in garagewith low headroom clearance 139.53728 139.53729Page Page Revisi6n de lossimbo/osy trminosde seguridad Preparaci6nde la puerta de su cochera HerramientasnecesariasPuertade unasola pieza Instalaciincon Unapuertaseccional Planificaci6nInstalacioncon Unapuertaseccional EN Posicion CerradaPuertade UNA Solapiezasin Carril Planificaci6n continUaInstalacioncon Puertasde Unasolapieza Puertade UnapiezaconcarrilContornillos3 Inventario de la caia de cartdnCubiertadela banda SecciOndelantera delrielcabezalInventario de piezas Tornilleriay PiezasparaelmontajeTornilleriay Piezasparalainstalacion Partesuperior Monte e/fie/e insta/e e/tro/eFije e/tie/a la unidadde/motor Estaspiezasse Muestranen SU TamaiorealNstale la po/ea Ioca Trole Destornillador Orificiode paro deltroleEstas Piezasse Iviuestranen SU Taiviaioreal Conranura Nsta/e /a bandaConector deltrole Estas Piezasse Muestran EN SU Tamaio NormalInstruccionesimportantesparalainstalacion Estas Piezasse Muestran EN SU TamaionormalDetermine d6nde va a insta/ar la mnsulade/cabeza Accesoriosde montajeInstalaciinde LA Mensuladel Cabezalen Elcieloraso Insta/e /a mnsu/a de/cabezaInstalaciinde LA Mensuladel Cabezalen LA Pared Delantera Estas Piezasse Muestran EN SU TamaiorealCo/oquee/fie/en la mnsula de/cabeza Orificiode montajeColoque el abridor en posici6n PUERTASECCIONAL0 Puertade Unasolapiezacon CarrilPuertade Unasolapiezasin Carril Cuelgueel abridor Estas Piezas SE Muestran EN SU TamaiorealInstale /as luces Coloquela Manija y la Cuerdade EmergenciaFije la m6nsuladela puerta PuertasseccionalesPuertas de madera Fije /a mnsu/a de la puerta contin#a Puertasde UnasolapiezaSI3LOPARA Puertasseccionales Conecteel brazo de la puerta al trole16-18x7/8 Correcto IncorrectoTodaslas Puertasde Unasolapieza Conectee/brazo de/a puerta a/tro/e contin#aColocar/as etiquetas de advertencia TroleAlambrede Controlde LA PUERTAFIGURA2 Instalar el controlde la puertaIntroduccion Montar Elcontrolde LA PUERTAFIGURA3Instalar e/contro/de/a puerta continUa Instale la ProtectorSystem+TENDERLOSCABLESDESDEELCONTROLHASTAELABRE-PUERTA FIGURA4 Instalaci6n en la pared Figuras2 y Instale la ProtectorSystem contin#aInstalacionde LAS Minsulas Instalacifin en el piso FiguraOpci#n a Instalaci#nsin cables preinstalados Insta/e /a ProtectorSystem contin#aMontaje Opci#n B Concables preinstaladosCorrectoincorrecto Requisitospara /a insta/aciCne/ ctricaAlineaciCnde los sensoresde reversa de seguridad Conexioncon CableadopermanenteIneaci6n de/os sensores de reversa de seguridad continUa Introducci6nProgramaci6nde/desp/azamiento Prueba Pruebe e/sistema de seguridadde reversaPrueba la ProtectorSystem AjusteInstale la bateria Prueba de la bateriaFunciones Pu/sadordebarra Funcionescontin#aContro/de /a puerta Paraabrir o cerrarla puertautilizarelpulsadorde barraConfiguraci6nde/a Smart Contro/Pane FuncionesPara borrar la memoria ProgramaciCnBorrartodoslos Dispositivos Una vez al mes C6moabrir la puerta manualmenteMantenimiento de su abridor de puerta de cochera Una vez al afioTablade Diagnistico Destello 4 Destellos 51DESTELLO 5 DestellosSensoresde SolucionTablade Diagnostico Destellos 1DESTELLOOpcionalesParalainstalaci6ndelsensorde Seguridadenlaparedo enelpisoS61opara puertas seccionales MY-HOME

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.
Top Page Image Contents