Craftsman 139.3043 owner manual Install the Door Control, Introduction, Wirethe DOORCONTROLFIGURE2

Page 22

INSTALLATION STEP 1 1

Install the Door Control

INTRODUCTION

NOTE:Older Craftsman accessories and third party products are not compatible.

Your garage door opener is compatible with up to 2 door controls.

Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach,and awayfrom the moving parts of the door.

NOTE:For gang box installations it is not necessary to drill holes or instafl the drywafl anchors. Use the existing holes in the gang box (Figure 1).

WIRETHE DOORCONTROL(FIGURE2)

1.Strip 7/16 inch (11 mm) of insulation from one end of the wire and separatethe wires.

2.Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw.

Pre-wired installations:Choose any two wires to connect, but make note of which wires are used so that the correct wires are

connected to the garage door opener in a later step.

MOUNTTHE DOORCONTROL(FIGURE3)

1.Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole.

2.Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall.

3.Position the bottom hole of the door control over the screw and slide down into place.

4.Lift the push bar and mark the top hole.

5.Removethe door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw.

6.Position the bottom hole of the door control over the screw and slide down into place. Attach the top screw.

Figure2

Top Mounting Hole

Bell Wire

Terminal

ScrewsBottomMountingHole

To prevent possible SERIOUSINJURYor DEATHfrom electrocution:

Besure power is NOTconnected BEFOREinstalling door control.

Connect ONLYto 12 VOLTlow voltage wires.

To prevent possible SERIOUSINJURYor DEATHfrom a closing garagedoor:

Install door control within sight of garagedoor, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

NEVERpermit children to operate or play with door control push buttons or remote control transmitters.

Activate door ONLYwhen it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

ALWAYS keepgarage door in sight until completely closed. NEVERpermit anyone to cross path of closing garage door.

HARDWARESHOWN ACTUALSIZE

-Ni]i-7-Ni]-iN-q-fii>

Screw 6ABx1-1/4"

Insulated

(std installation)

Staples

(pre-wired)

Drywall Anchors

Figure 1

 

PRE-WIRED INSTALLATIONS:

 

Choose any two wires to

 

connect, but make note of

 

which wires are used.

 

6-32x1"

 

e

ire Screw

 

6-32x1"

Figure3

 

Screw 6ABx1-1/4"

Screw 6ABx1-1/4"

22

Image 22
Contents Garagedooropener Abridorde Puertadecochera 41-42 WarrantySafety SymbolReviewand Signal WordReview BackCoverPreparingyourgarage door One-Piece DoorAccessDoor Sectionaldoor InstallationSectionaldoorinstallation PlanningONE-PIECEDOORWITHOUT Track ONE-PIECEDOOR InstallationsONE-PIECEDOORWITH Track CartonInventory With screws3HardwareInventory AssemblyhardwareInstallationhardware NutInner Trolley Assemble the Rail and Install the TrolleyFasten the Rail to the Motor Unit Rail TOPInstall the Idler Pulley Install the Belt Importantinstallationinstructions Set the Tensionand Install the SprocketCoverHardware Determine the HeaderBracketLocationOne-piecedoor withouttrack Ceilingheaderbracketinstallation Install the Header BracketWall Headerbracketinstallation SpringAttach the Raft to the Header Bracket HeaderWall HeaderBracket IdlerPulley Header0Sectionaldooror ONE-PIECEDOORWITH Track Positionthe OpenerONE-PIECEDOORWITHOUTTRACK Orts Hang the OpenerFinished Ceiling 100WattMax Install the LightsAttach the Emergency Release Rope and Handle WattMax StandardLightBulbSectionaldoors Metal, insulated or light weight factoryreinforced doorsFasten the Door Bracket WoodDoorsSelf-ThreadingScrew 1/4-14x5/8 BracketHole alignment alternative Connect Door Arm to TrolleySectionaldoorsonly Straight DoorArmOuter ConnectDoorArm to Tro//eyAttach the Warning Labels RingIntroduction Install the Door ControlWirethe DOORCONTROLFIGURE2 Connected to the garage door opener in a later stepWirethe Doorcontrolto the Garagedooropener Install The ProtectorSystemInstall the Door Control Importantinformationaboutthe Safetyreversing SensorWaft installation Figures2 Installingthe BracketsGarage door trackinstallation preferred Floor installation FigureMounting Option B Pre-Wired /nsta//ationInsta// TheProtectorSystem Connectto GaragedooropenerWireNuts Aligningthe SafetyReversingSensorsPermanentwiring Optionb Electrical RequirementsIf the Greenled on the Receivingsensoris not Glowing Aligning the Safety Reversing SensorsIf the Amberled Onthe Sendingsensoris not Glowing ProgrammingbuttonsIMPORTANTNOTEFor one-piece door installations refer to Programthe TravelImportantsafetycheck Testthe SafetyReversalSystemAdjust Test The ProtectorSysterBatterystatusled Greenled Testthe BatteryInstall the Battery Chargethe BatteryFeatures Door Control Settings Smart ControlPane/SetupFeatures Menu NavigationENTERbutton ProgrammingTo Erase the Memory Eraseall Remotecontrolsand KeylessentriesEverymonth To Openthe Door ManuallyCareof YourOpener EveryyearFlash 3 Flashes DiagnosticchartFlash 2 Flashes Flash 4 Flashes4FLASHES Flashes Diagnostic UP DownArrow Flashes Flashes 6 FlashesRail Assembly Parts Installation Parts Description41B135 Line cord Motor Unit Assembly PartsKEY Part 41A7630ForSectionalDoorsOnly41A7569 Available only throughSears Parts & ServiceInstallingopener in garagewith low headroom clearance 139.53728 139.53729Page Page Revisi6n de lossimbo/osy trminosde seguridad Herramientasnecesarias Preparaci6nde la puerta de su cocheraPuertade unasola pieza Instalaciincon Unapuertaseccional Planificaci6nInstalacioncon Unapuertaseccional EN Posicion CerradaPuertade UNA Solapiezasin Carril Planificaci6n continUaInstalacioncon Puertasde Unasolapieza Puertade UnapiezaconcarrilContornillos3 Inventario de la caia de cartdnCubiertadela banda SecciOndelantera delrielcabezalTornilleriay Piezasparaelmontaje Inventario de piezasTornilleriay Piezasparalainstalacion Partesuperior Monte e/fie/e insta/e e/tro/eFije e/tie/a la unidadde/motor Estaspiezasse Muestranen SU TamaiorealTrole Destornillador Orificiode paro deltrole Nstale la po/ea IocaEstas Piezasse Iviuestranen SU Taiviaioreal Conranura Nsta/e /a bandaConector deltrole Estas Piezasse Muestran EN SU Tamaio NormalInstruccionesimportantesparalainstalacion Estas Piezasse Muestran EN SU TamaionormalDetermine d6nde va a insta/ar la mnsulade/cabeza Accesoriosde montajeInstalaciinde LA Mensuladel Cabezalen Elcieloraso Insta/e /a mnsu/a de/cabezaInstalaciinde LA Mensuladel Cabezalen LA Pared Delantera Estas Piezasse Muestran EN SU TamaiorealCo/oquee/fie/en la mnsula de/cabeza Orificiode montajePUERTASECCIONAL0 Puertade Unasolapiezacon Carril Coloque el abridor en posici6nPuertade Unasolapiezasin Carril Cuelgueel abridor Estas Piezas SE Muestran EN SU TamaiorealInstale /as luces Coloquela Manija y la Cuerdade EmergenciaPuertasseccionales Fije la m6nsuladela puertaPuertas de madera Fije /a mnsu/a de la puerta contin#a Puertasde UnasolapiezaSI3LOPARA Puertasseccionales Conecteel brazo de la puerta al trole16-18x7/8 Correcto IncorrectoTodaslas Puertasde Unasolapieza Conectee/brazo de/a puerta a/tro/e contin#aColocar/as etiquetas de advertencia TroleAlambrede Controlde LA PUERTAFIGURA2 Instalar el controlde la puertaIntroduccion Montar Elcontrolde LA PUERTAFIGURA3Instale la ProtectorSystem+ Instalar e/contro/de/a puerta continUaTENDERLOSCABLESDESDEELCONTROLHASTAELABRE-PUERTA FIGURA4 Instalaci6n en la pared Figuras2 y Instale la ProtectorSystem contin#aInstalacionde LAS Minsulas Instalacifin en el piso FiguraOpci#n a Instalaci#nsin cables preinstalados Insta/e /a ProtectorSystem contin#aMontaje Opci#n B Concables preinstaladosCorrectoincorrecto Requisitospara /a insta/aciCne/ ctricaAlineaciCnde los sensoresde reversa de seguridad Conexioncon CableadopermanenteIneaci6n de/os sensores de reversa de seguridad continUa Introducci6nProgramaci6nde/desp/azamiento Prueba Pruebe e/sistema de seguridadde reversaPrueba la ProtectorSystem AjusteInstale la bateria Prueba de la bateriaFunciones Pu/sadordebarra Funcionescontin#aContro/de /a puerta Paraabrir o cerrarla puertautilizarelpulsadorde barraConfiguraci6nde/a Smart Contro/Pane FuncionesProgramaciCn Para borrar la memoriaBorrartodoslos Dispositivos Una vez al mes C6moabrir la puerta manualmenteMantenimiento de su abridor de puerta de cochera Una vez al afioTablade Diagnistico Destello 4 Destellos 51DESTELLO 5 DestellosSensoresde SolucionTablade Diagnostico Destellos 1DESTELLOSeguridadenlaparedo enelpiso OpcionalesParalainstalaci6ndelsensordeS61opara puertas seccionales MY-HOME

139.3043 specifications

The Craftsman 139.3043 garage door opener stands out as a robust and reliable solution for homeowners looking to enhance the functionality and security of their garage spaces. This model is designed with the latest technologies and features, making it one of the preferred choices in the market.

One of the key features of the Craftsman 139.3043 is its powerful motor, which provides a smooth and quiet operation. With a lifting capacity that accommodates most standard residential garage doors, this opener ensures that users can operate their doors seamlessly without unnecessary noise. The blend of power and quiet functionality enhances the overall user experience, making it ideal for homes with bedrooms or living areas adjacent to the garage.

The opener also boasts a durable rail system, designed for easy installation and longevity. The straightforward design simplifies the installation process, enabling a typical DIY enthusiast to set it up without the need for professional assistance. Additionally, the sturdy construction of the rail system ensures that it can withstand the rigors of daily use.

Safety and security are paramount with the Craftsman 139.3043. It incorporates advanced safety features, such as the automatic reverse function, which prevents accidents by reversing the door's motion when an obstacle is detected. This feature adds peace of mind for families with children and pets. Furthermore, the built-in security technology includes a rolling code system that changes the access code each time the remote is used, thus protecting against potential unauthorized access.

The Craftsman 139.3043 is equipped with remote control capabilities, allowing users to open and close their garage doors from a distance. The remote is designed to be user-friendly, with buttons that are easy to operate. Additionally, many models include a smartphone app integration, empowering users to control their garage door via their mobile devices, providing convenience and modern accessibility.

Another notable characteristic is the vibrant LED lighting that illuminates the garage space when the door is in use. This not only enhances visibility but also contributes to the overall safety of the area, preventing accidents in dimly lit environments.

In summary, the Craftsman 139.3043 garage door opener combines power, ease of use, advanced safety features, and modern technology. Its reliable performance and user-friendly elements make it a top choice for homeowners seeking an effective solution to their garage door needs.