Mitsubishi Electronics PCA-A.KA4 Function settings, For IR wireless remote controller

Page 8
MODEL SELECT
MODEL SELECT

6. Electrical work

MODELSELECT



ON/OFF TEMP

 

FAN

AUTO STOP

MODE

VANE

AUTO START

CHECK

LOUVER

h

TEST RUN

 

min

6.2.2.For IR wireless remote controller

1) Installation area

• Area in which the IR wireless remote controller is not exposed to direct sunshine.

• Area in which there is no nearby heating source.

• Area in which the IR wireless remote controller is not exposed to cold (or hot) winds.

• Area in which the IR wireless remote controller can be operated easily.

• Area in which the IR wireless remote controller is beyond the reach of children.

2)Setting (Fig. 6-3) Insert batteries.

Press the SET button with something sharp at the end.

blinks and Model No. is lighted.

Press the temp buttons to set the Model No.

If you mistook the operation, press the ON/OFF button and operate again from procedure .

Press the SET button with something sharp at the end.

SET RESET CLOCK

and Model No. are lighted for 3 seconds, then turned off.

Fig. 6-3

 

MODELSELECT

 



ON/OFF

TEMP

 

 

 

 

FAN

 

AUTO STOP

MODE

VANE

 

AUTO START

CHECK

LOUVER

h

TEST RUN

 

 

min

SET RESET CLOCK

Fig. 6-4

Mode number

Setting number

Refrigerant address

Unit number

F

 

TEMP.

 

 

ON/OFF

 

 

 

 

 

 

 

 

A

E

 

MENU

ON/OFF

 

FILTER

BACK

MONITOR/SET

DAY

 

CHECK

TEST

 

G

PAR-21MAA

CLOCK

OPERATION

CLEAR

 

B

 

 

 

 

 

 

 

C D

Fig. 6-5

Indoor

Outdoor

 Model No.

PCA

PUZ

001

PUY

033

 

3) Assigning a IR wireless remote controller to each unit

Each unit can be operated only by the assigned IR wireless remote controller. Make sure each pair of an indoor unit PC board and a IR wireless remote controller is assigned to the same pair No.

4)IR wireless remote controller pair number setting operation (Fig. 6-4) Press the SET button with something sharp at the end.

Start this operation from the status of IR wireless remote controller display turned off.

MODEL SELECT blinks and Model No. is lighted.

Press the min button twice continuously. Pair No. “0” blinks.

Press the temp buttons to set the pair number you want to set.

If you mistook the operation, press the ON/OFF button and operate again from procedure .

Press the SET button with something sharp at the end. Set pair number is lighted for 3 seconds then turned off.

 Pair No. of IR wireless remote controller

Indoor PC board

0

Initial setting

1

Cut J41

2

Cut J42

3-9

Cut J41, J42

6.3. Function settings

6.3.1 Function setting on the unit (Selecting the unit functions)

1)For wired remote controller (Fig. 6-5)

Changing the power voltage setting

•Be sure to change the power voltage setting depending on the voltage used. Go to the function setting mode.

Switch OFF the wired remote controller.

Press the  and  buttons simultaneously and hold them for at least 2

seconds. FUNCTION will start to flash.

Use the  button to set the refrigerant address ( ) to 00.

Press  and [--] will start to flash in the unit number ( ) display. Use the  button to set the unit number ( ) to 00.

Press the  MODE button to designate the refrigerant address/unit number. [--]

will flash in the mode number ( ) display momentarily.



Press the  buttons to set the mode number ( ) to 04.



Press the  button and the current set setting number ( ) will flash.

Use the  button to switch the setting number in response to the power supply voltage to be used.

Power supply voltage

230 V : setting number = 1

208 V : setting number = 2

 Press the MODE button  and mode and the setting number ( ) and ( ) will change to being on constantly and the contents of the setting can be confirmed.

Press the FILTER  and TEST RUN  buttons simultaneously for at least two seconds. The function selection screen will disappear momentarily and the air conditioner OFF display will appear.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Air-Conditioners Contents Safety precautionsInstallation location Installing the indoor unitInstalling the indoor unit Fig Directly suspending the unit Installing proceduresFresh air intake hole Fig Indoor unit preparation FigInstalling the refrigerant piping PrecautionsConnecting pipes Fig Indoor unit FigElectric wiring Installing procedures FigDrainage piping work Electrical workWired remote controllers setting Remote controllerFor wired remote controller Function settings For IR wireless remote controllerInstallation area Setting -3 Insert batteriesFor IR wireless remote controller Fig Or maintenance, be sure to record the changes with a markSetting column of the Function table Function tableTest run Before test runTest run Self-checkPlease Wait Stable operation Easy maintenance function For wired remote controller onlyDisplay example Comp discharge temperature 147˚F Index Consignes de sécuritéEmplacement pour l’installation Installation de l’appareil intérieurDimensions externes Appareil intérieur Fig Dimensions extérieures Appareil extérieurInstallation de l’appareil intérieur Fig Suspendre l’appareil directement Méthodes d’installationEntrée d’air frais Fig 5. Préparation de l’appareil intérieur FigInstallation de la tuyauterie du réfrigérant ConsignesConnexion des tuyaux Fig Appareil intérieur FigInstallations électriques Installation électrique FigMéthodes d’installation Fig Mise en place du tuyau d’écoulementTélécommande Pour la télécommande à filRéglage de 2 télécommandes à fil Appareil intérieur-appareil extérieur × AWG16 polarPour télécommande sans fil infrarouge Lieu d’installationRéglage des fonctions Programmation Fig2. Réglage des fonctions sur la commande à distance Tableau des fonctionsAuto-vérification Marche d’essaiMarche d’essai Contrôleur extérieur Pendant environ deux minutes après la mise sous tensionExemple d’affichage température de décharge du comp F Fonctionnement stable Stable op rationContenido Medidas de SeguridadLugar en que se instalará Instalación de la unidad interiorPreparación de la unidad interior Fig Instalación de la unidad interior FigOrificio de entrada de aire fresco Fig Instalación de los tubos del refrigerante PrecaucionesTubos de conexió Fig Unidad interior FigTubería de drenaje Trabajo eléctricoCableado eléctrico Fig Procedimientos de instalación FigAjuste de 2 controladores remotos cableados Control remotoPara el controlador remoto cableado Ajuste de funciones Para el controlador remoto inalámbrico por infrarrojosZona de instalación Preparación inicial FigAjuste de funciones en el controlador remotor AjustePrueba de funcionamiento Antes de realizar las pruebasPrueba de funcionamiento AutotestPara información detallada Temperatura anormal del cuerpo de refrigeraciónCompruebe la pantalla de Parada de seguridad del ventilador de la unidad exteriorUsed since the filter reset was performed Procedimientos de manejo del modo de mantenimientoPage RG79D508H02

PCA-A.KA4 specifications

The Mitsubishi Electronics PCA-A.KA4 is an advanced air conditioning unit designed to deliver exceptional comfort and efficiency in various settings. Known for its innovative technology and user-friendly design, this model is a preferred choice for both residential and commercial applications.

One of the main features of the PCA-A.KA4 is its advanced inverter technology. This system allows for variable speed operation, which means that the compressor can adjust its output based on the current cooling demand. As a result, the unit operates more efficiently, consuming less energy compared to traditional fixed-speed air conditioners. This not only reduces energy bills but also lessens the environmental impact, making the PCA-A.KA4 an eco-friendly option.

The PCA-A.KA4 also boasts a high seasonal energy efficiency ratio (SEER) rating, which indicates its effectiveness in converting electricity into cooling power over an entire season. This high efficiency is a significant advantage, particularly in regions with hot climates, where air conditioning usage is prevalent.

Another notable characteristic is the use of cutting-edge air purification technology. The PCA-A.KA4 is equipped with a multi-stage filtration system that captures dust, allergens, and other airborne particles. This feature enhances indoor air quality, ensuring that occupants breathe cleaner and healthier air, which is particularly beneficial for those with respiratory issues or allergies.

In terms of user convenience, the PCA-A.KA4 is designed with an intuitive remote control that provides easy operation from anywhere in the room. Additionally, the unit can be integrated with smart home systems, allowing for remote access and control via smartphones or tablets. This flexibility enables users to adjust settings even when they are away from home, ensuring optimal comfort at all times.

The PCA-A.KA4 also includes a quiet operation mode, minimizing noise levels to promote a peaceful environment. This feature is especially valuable in bedrooms or offices where concentration and relaxation are key.

Overall, the Mitsubishi Electronics PCA-A.KA4 represents a harmonious blend of comfort, efficiency, and smart technology. With its advanced features and user-friendly design, it stands out as a reliable air conditioning solution capable of meeting modern demands for both performance and sustainability. Whether for home or business use, the PCA-A.KA4 delivers a superior cooling experience that enhances overall well-being.
Top Page Image Contents