Sharp R-1900J Operation Of Touch Control Panel, Memory Operation, Before Operation, Cancellation

OPERATION OF TOUCH CONTROL PANEL

Before Operation

*Before operating your new oven, make sure you read and understand this operation manual completely.

1)Plug in the oven. Nothing will appear in the display at this time.

2)Open the door. The display shows “0”.

3)Close the door.

4)Control panels can only be operated when the door is closed.

5)Your oven has 3 ways to select memory numbers.

See CUSTOM SETTING 1. To Set Input Method on page 9. The factory setting is Dual digit Input .

Cancellation:

1.Cooking data is canceled when keys are not pressed for more than three minutes when setting programming.

2.Cooking stops when the STOP/CLEAR pad is pressed and cooking data remains. However if subsequent keys are not

pressed within three minutes, cooking data will be canceled. To resume cooking press the START pad.

3.Cooking stops when the door is opened and cooking data remains. However once the door is closed, cooking data will be canceled if subsequent keys are not pressed within 3 minutes. To resume cooking press the START pad.

4.Cooking is immediately canceled by pressing the STOP/ CLEAR pad twice.

Checking food:

Press the STOP/CLEAR pad then open the door, check food, close the door and press the START pad to continue cooking.

Cooking Completion:

When food is not taken out after cooking completion, “End” will be shown in the display until the food is taken out.

If you do not operate the oven for 3 minutes or more (i.e. closing the door or pressing the STOP key), your oven will automatically shut down, so you will not be able to operate the oven until you open and close the oven door.

NOTE : When you set Demonstration mode or while cooking fan work after cooking, your oven will not shut down automatically.

HELPFUL TIPS for the Memory Input Method

The Memory Input Method determines how to input memory numbers for Memory Cooking and Custom Setting and Saving Memories, therefore follow the method below. Refer to HELPFUL TIPS below as well as to Memory Cooking below.

1.	Dual Digit Input: Must input two numbers to select a		The Memory Input Method
	memory, even though the first number is 0. Memory	Memory No.
	programming is limited to 0 - 99.
		Memory	Examples	0	2	12	22
2.	Single Digit Input: Can only input one number to select
	a memory. Memory programming is limited to 0 - 9.	Input Method
3.	Repeat Digit Input: Input one, two, or three numbers to	Dual Digit Input		0, 0	0, 2	1, 2	2, 2
4.	select a memory. Memory programming is limited to 0 - 29.	Single Digit Input		0	2
	For Repeat Digit Input/Auto Start ON only, push number	Repeat Digit Input		0	2	2, 2	2, 2, 2
	pads within one second of the previous number.

5.Regardless of input method selected, Counter Check/Clear (Custom Setting 7) and Multiplication Factors for Double/ Triple Quantity (Custom Setting 10) only use the Dual Digit Input method. As for Custom Setting 10, enter memory number after pressing the DOUBLE/TRIPLE QUANTITY pad.

MEMORY OPERATION

Memory Cooking

*Your oven has 100 memory banks from 0 to 99. Memory contents from memory number 0 to 29 are the same in Dual, and Repeat Digit Input methods.

*Memory 0 - 9 are programmed as factory settings. See the table of Programmed Memories and the Memory Input Method on the right side. Memory 10 - 99 must be programmed before using Memory Cooking. When a memory number which has not been programmed is entered, “End” will be shown in the display. See Saving Memories on page 15-19 to programme a new memory.

Programmed Memories and the Memory Input Method

Memory	Dual	Single	Repeat	Cook	Output
	Digit	Digit	Digit
No.				time	power
	Input	Input	Input
1	01	1	1	5 sec.	100%
2	02	2	2	10 sec.	100%
3	03	3	3	20 sec.	100%
4	04	4	4	30 sec.	100%
5	05	5	5	40 sec.	100%
6	06	6	6	50 sec.	100%
7	07	7	7	1 min.	100%
8	08	8	8	1 min. 15 sec.	100%
9	09	9	9	1 min. 30 sec.	100%
0	00	0	0	2 min.	100%

5

R-1900J [EN].indd Sec1:5

4/28/09 10:01:25 AM