KitchenAid LI3Y7C, W10322991C Install Range Hood, Range Hood Mounting Screws Installation

Page 7

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

5.Determine and mark the centerline on the wall where the canopy hood will be installed.

6.Select a mounting height between a minimum of

24" (61.0 cm) for an electric cooking surface, a minimum

of 27" (68.6 cm) for a gas cooking surface, and a suggested maximum of 36" (91.4 cm) above the range to the bottom of the hood. Mark a reference line on the wall.

7.Tape template in place, aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall.

A

DRILL2 (TW O)3/16"PILOTHOLESTHROUGH STUDSOR REAR W ALLSUPPORT

Vertical Centerline

REAR W ALL

M OUNTING TEM PLATE

C

L

ALIGN BOTTOM EDGE

W ITH PENCILLINE

INDICATING BOTTOM

OFTHEHOOD

Installation Height

HorizontalLine

BC

A.Centerline

B.Fastener locations

C.Mounting height reference

8.Mark centers of the fastener locations through the template to the wall.

IMPORTANT: All canopy mounting screws must be installed into wood. If there is no wood to screw into, additional wall framing supports may be required.

Remove the template.

9.Drill ³⁄₁₆" (4.8 mm) pilot holes at all locations where screws are being installed into wood.

10.Install 2 - 5 x 45 mm mounting screws. Leave a ¹⁄₄" (6.4 mm) gap between the wall and the back of the screw head to slide range hood into place.

¹⁄₄" (6.4 mm)

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent cover assembly

1.Position vent cover bracket on wall about ¹⁄₈" (3.0 mm) away from the ceiling.

2.Mark the hole locations.

3.Drill ³⁄₈" (9.5 mm) holes for wall anchors and insert anchors flush with the wall.

AC

B

D

A. 8 x 40 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

4.Attach vent cover support bracket to wall.

Complete Preparation

1.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See “Venting Requirements” section.

2.Determine the required height for the home power supply cable and drill a 1¼" (3.2 cm) hole at this location.

3.Run the home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4.Use caulk to seal all openings.

Install Range Hood

1.Using 2 or more people, hang range hood on 2 mounting screws through the mounting slots on back of hood.

A

B

C

A. Mounting screws

B. Mounting slots

C. Lower mounting screws

2.Remove the grease filter. See “Range Hood Care” section.

3.Level the range hood and tighten upper mounting screws.

4.Install 2 - 5 x 45 mm lower mounting screws and tighten.

7

Image 7
Contents Canopy Range Hood Table DES Matières Range Hood SafetyImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Venting Requirements Electrical Requirements Installation InstructionsPrepare Location Complete Preparation Install Range HoodRange Hood Mounting Screws Installation Vent Cover Support Bracket InstallationMake Electrical Connection For vented installations onlyFor non-vented recirculating installations only Connect Vent SystemComplete Installation Install Vent CoversOperating the blower Range Hood USERange Hood Controls Operating the lightExterior Surfaces CleaningNon-Vented recirculating Installation Filters Range Hood CareAGC Wiring DiagramCanada Assistance or ServiceAccessories U.S.AThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreImportantes Instructions DE Sécurité Exigences d’emplacement Exigences DinstallationOutils et pièces Air dappoint Dimensions du placardInstallation dans une région à climat froid Exigences concernant l’évacuationCalcul de la longueur effective du circuit dévacuation Décharge à Installation sans Travers le toit Travers le murSpécifications électriques Décharge par larrièreInstallation de la bride de cache-conduit Instructions DinstallationPréparation de lemplacement Installation des vis de montage de la hotteRaccordement du circuit dévacuation Installation de la hotteRaccordement électrique Installation des cache-conduitsUtilisation de la lampe Achever l’installationCommandes de la hotte de cuisinière Utilisation DE LA HotteNettoyage Entretien DE LA HotteOhms Schéma DE CâblageAccessoires Assistance OU ServiceAu Canada La présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidAll rights reserved W10322991C

LI3Y7C, W10322991C specifications

The KitchenAid W10322991C, LI3Y7C is an exceptional addition to any home kitchen, celebrated for its combination of functionality, durability, and innovative technology. This specific model stands out for its versatility and user-friendly design, making it an ideal choice for both amateur cooks and professional chefs alike.

One of the main features of the KitchenAid W10322991C is its impressive motor performance. Engineered to handle even the most challenging recipes, the powerful motor ensures consistency in mixing and kneading. This feature is particularly important for baking enthusiasts who require precise measurements and thorough ingredient incorporation to achieve the perfect dough and batter textures.

In terms of build quality, the W10322991C model boasts a robust construction using high-grade materials. This durability not only enhances the mixer’s lifespan but also contributes to its stability during operation. The design features a weighted base that minimizes vibrations, allowing for a noiseless experience in the kitchen.

A standout technology incorporated into this model is the planetary mixing action. This allows the mixing attachment to rotate in one direction while the bowl rotates in the opposite direction, ensuring that all ingredients are thoroughly combined. This efficient mixing method guarantees that no ingredient is left unmixed, delivering an even consistency in every preparation.

The KitchenAid W10322991C also comes with multiple speed settings, allowing users to select the ideal speed for any task – from gentle mixing to high-speed whipping. Additionally, the inclusion of various attachments such as a flat beater, wire whip, and dough hook further expands the machine’s capabilities, enabling users to tackle a wide range of culinary tasks.

Another characteristic that enhances user convenience is the tilting head design. This feature allows for easy access to the bowl, making it simpler to add ingredients or switch attachments without any hassle. Coupled with a generous bowl capacity, this design is particularly beneficial for larger batches or intricate recipes.

In conclusion, the KitchenAid W10322991C, LI3Y7C is a powerhouse of a kitchen appliance combining efficiency, durability, and ease of use. With its advanced mixing technologies, robust construction, and versatile functions, it empowers users to explore their culinary creativity, making it a staple in kitchens around the world. Whether baking bread, mixing cookie dough, or preparing whipped cream, this model ensures outstanding results every time.