KitchenAid W10154991A Replace Oven RacksandWarmingDrawer, Complete Installation

Page 18

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the “LITE” position.

The flame should light within 4 seconds. The first time a burner is lit it may take longer that 4 seconds to light because of air in the gas line.

TripleTier® Flame Burner

To start simmer burner:

Push in and turn control knob to “LITE.”

The flame should light within 4 seconds. The first time a burner is lit it may take longer that 4 seconds to light because of air in the gas line.

To start power burner:

Push in control knob again and turn to “POWER BURNER HI” to light the outer burner.

The flame should light within 4 seconds. The first time a burner is lit it may take longer that 4 seconds to light because of air in the gas line.

If burners do not light properly:

■Turn cooktop control knob to the “OFF” position.

■Check that the range is plugged in and the circuit breaker has not tripped or the household fuse has not blown.

■Check that the gas shutoff valves are set to the “open” position.

■Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, turn control knobs to “Off” and contact your dealer or authorized service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop “low” burner flame should be a steady blue flame approximately ¼" (0.64 cm) high.

A

B

A.Low flame

B.High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly underneath the control knob.

A

A. Valve stem

If the “low” flame needs to be adjusted:

1.Remove the control knob.

2.Hold the knob stem with a pair of pliers. Use a small flat- blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size.

3.Replace the control knob.

4.Test the flame by turning the control from “LO” to “HI,” checking the flame at each setting.

To adjust TripleTier® Flame burner:

1.Remove the control knob.

2.Insert a flat-blade screwdriver into adjustment locations shown in the following illustration and engage the slotted screw. Turn the screw until the flame is the proper size.

A

B

A.Simmer burner regulation

B.Power burner regulation

3.Replace the control knob.

4.Test the flame by turning the control from “LO” to “HI,” checking the flame at each setting.

Replace Oven RacksandWarmingDrawer

Replace oven racks in oven cavity. Replace warming drawer or storage drawer.

To Replace Warming Drawer:

1.Align the drawer glides with the receiving guides.

2.Push drawer in all the way.

Gently open and close the drawer to ensure it is seated properly on the slides.

Complete Installation

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Dispose of/recycle all packaging materials.

4.Check that range level. See “Level Range.”

5.Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by protective shipping material. Dry thoroughly with a soft cloth. For more information, see the “Range Care” section of the Use and Care Guide.

6.Read “Range Use” in the Use and Care Guide.

7.Turn on surface burners and oven. See the Use and Care Guide for specific instruction on range operation.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DE 30 76,2 CM W10154991ARange Safety Table DES MatièresWhat to do if YOU Smell GAS Installation Requirements ToolsandPartsLocation Requirements Mobile home installations require Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Slide-in RangeInstallation Clearances Freestanding RangesSlide-In Ranges Local codes may permit the use of a UL listed, 3-wire If connecting to a 4-wire systemIf connecting to a 3-wire system Electrical Requirements U.S.A.OnlyType of Gas Electrical Requirements -Canada OnlyGas Supply Requirements Gas Supply LineBurner Input Requirements Gas Supply Pressure TestingCountertopPreparation Gas Pressure RegulatorMeasureforProperHeight Installation InstructionsUnpack Range Slide-In RangesAdjust LevelingLegs InstallAnti-TipBracketLevel Range RemoveWarming DrawerVerifyAnti-Tip Bracket Location To Remove Warming DrawerStyle 1 Power supply cord strain relief Power Supply CordDirect Wire Electrical Connection -U.S.A.OnlyWire connection Power Supply Cord Style 2 Direct wire strain reliefDirect Wire Installation Copper or Aluminum Wire Wire Connection Direct WireMake Gas Connection Typical rigid pipe connectionTypical flexible connection Initial lighting and gas flame adjustmentsElectronicIgnitionSystem Complete ConnectionComplete Installation Replace Oven RacksandWarmingDrawerTo Convert Gas Pressure Regulator GAS ConversionsLPGas Conversion If range does not operate, check the followingTo Convert Standard Surface Burners Reinstall the cap onto the regulatorTo Convert TripleTier Flame Burners on some models Gas orifice spuds are stamped with a number, marked withNaturalGas Conversion To Convert TripleTier Flame Burner on some models Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences D’INSTALLATION Exigencesd’emplacementOutillageetpièces Dimensions du produit Cuisinière autoportante Cuisinière encastréeDégagements de séparation à respecter Cuisinières autoportantesCuisinières encastrées Type de gaz Spécifications électriquesSpécifications del’alimentation engaz Gaz naturelDébit thermique des brûleurs PréparationduplandetravailCanalisation de gaz Détendeur de gazMesurespourunehauteurappropriée Instructions DinstallationDéballagede lacuisinière Réglage despieds de nivellementInstallation de la brideantibasculement Réglage del’aplomb delacuisinière Vérificationdelemplacement de labride AntibasculementRetraitdutiroir-réchaud Raccordement à la canalisation degazCuisinière encastrée Installée sur le brûleur avant gaucheRaccordement typique par raccord flexible Compléter le raccordemantBrûleur à flamme TripleTier Système dallumageélectroniqueAllumage initial et réglages des flammes Si le brûleur ne sallume pas correctementConversions Pour Changement DE GAZ Réinstallationdes grillesdufouret Dutiroir-réchaudAcheverlinstallation Conversion pourlalimentationaupropaneConversion des brûleurs standard de la table de cuisson Important Ne pas enlever le détendeurDétendeur Enlever la plaque associée au gicleur externe Conversionpourlalimentation augaz naturel Chiffre gravé Holes in bracket Trous dans la bride All rights reserved

W10154991A specifications

The KitchenAid W10154991A is a versatile kitchen appliance designed to simplify meal preparation while enhancing culinary creativity. This food processor is equipped with innovative features and technologies that make it an essential addition to any modern kitchen.

One of the main features of the W10154991A is its powerful motor, which allows for quick and efficient processing of various ingredients. Whether you're chopping vegetables, shredding cheese, or mixing dough, this food processor can handle a wide range of tasks with ease. The motor's robust performance ensures that you can complete your cooking projects in a fraction of the time compared to using manual methods.

Another significant characteristic of the KitchenAid W10154991A is its variety of attachments and blades. The food processor comes equipped with multiple blades for different functions, including slicing, shredding, and chopping. This versatility enables users to achieve the desired texture and consistency for their recipes, all with one appliance. The included attachments are designed for easy installation and removal, making the transition between tasks seamless.

The design of the W10154991A also speaks to its user-friendly nature. It features a large capacity bowl, allowing you to process larger quantities of ingredients at once, which is ideal for meal prepping or when entertaining guests. The bowl is made from durable materials that can withstand the rigors of daily use while remaining easy to clean, as many parts are dishwasher safe.

Safety is a priority in the design of the KitchenAid W10154991A. It includes a safety lock feature that ensures the processor will not operate unless the bowl and lid are correctly secured. This feature gives users peace of mind while using the appliance and helps prevent accidents in the kitchen.

In terms of technology, the KitchenAid W10154991A employs a straightforward control panel that includes several speed settings. This means you can select the perfect speed for the task at hand, whether you need a gentle pulse or a steady chop. The intuitive design of the control panel makes it accessible for cooks of all skill levels.

In conclusion, the KitchenAid W10154991A food processor is an excellent investment for anyone looking to enhance their cooking experience. With its powerful motor, versatile attachments, user-friendly design, and safety features, this appliance stands out in the crowded market of kitchen gadgets. It empowers users to explore their culinary potential while simplifying time-consuming tasks in the kitchen.
Top Page Image Contents