KitchenAid W10154991A RemoveWarming Drawer, VerifyAnti-Tip Bracket Location, Level Range

Page 12

RemoveWarming Drawer

Remove the warming or storage drawer to gain access to the lower section of the range. This will be necessary for some of the following installation steps.

To Remove Warming Drawer:

1.Open drawer to its full open position.

2.Locate the black loops on both sides of the drawer.

A

A. Loop

3.Pull both loops forward at the same time, then pull drawer out another inch.

4.Holding the drawer by its sides, not its front, gently pull it all the way out.

VerifyAnti-Tip Bracket Location

IMPORTANT: On models with a warming drawer, the rear range foot must be viewed from the front and slightly to one side of the range.

1.Making sure the anti-tip bracket is installed:

■Look for the anti-tip bracket securely attached to floor.

■Slide range back so rear range foot is under anti-tip bracket.

2.If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the “Location Requirements” section.

Level Range

Place rack in oven. Place level on rack and check levelness of the range, first side to side; then front to back.

If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket.

Use a wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DE 30 76,2 CM W10154991ARange Safety Table DES MatièresWhat to do if YOU Smell GAS Installation Requirements ToolsandPartsLocation Requirements Mobile Home Additional Installation Requirements Product Dimensions Freestanding RangeMobile home installations require Slide-in RangeInstallation Clearances Freestanding RangesSlide-In Ranges If connecting to a 4-wire system If connecting to a 3-wire systemLocal codes may permit the use of a UL listed, 3-wire Electrical Requirements U.S.A.OnlyElectrical Requirements -Canada Only Gas Supply RequirementsType of Gas Gas Supply LineGas Supply Pressure Testing CountertopPreparationBurner Input Requirements Gas Pressure RegulatorInstallation Instructions Unpack RangeMeasureforProperHeight Slide-In RangesAdjust LevelingLegs InstallAnti-TipBracketRemoveWarming Drawer VerifyAnti-Tip Bracket LocationLevel Range To Remove Warming DrawerPower Supply Cord Direct WireStyle 1 Power supply cord strain relief Electrical Connection -U.S.A.OnlyWire connection Power Supply Cord Style 2 Direct wire strain reliefDirect Wire Installation Copper or Aluminum Wire Wire Connection Direct WireMake Gas Connection Typical rigid pipe connectionInitial lighting and gas flame adjustments ElectronicIgnitionSystemTypical flexible connection Complete ConnectionComplete Installation Replace Oven RacksandWarmingDrawerGAS Conversions LPGas ConversionTo Convert Gas Pressure Regulator If range does not operate, check the followingReinstall the cap onto the regulator To Convert TripleTier Flame Burners on some modelsTo Convert Standard Surface Burners Gas orifice spuds are stamped with a number, marked withNaturalGas Conversion To Convert TripleTier Flame Burner on some models Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences D’INSTALLATION Exigencesd’emplacementOutillageetpièces Dimensions du produit Cuisinière autoportante Cuisinière encastréeDégagements de séparation à respecter Cuisinières autoportantesCuisinières encastrées Spécifications électriques Spécifications del’alimentation engazType de gaz Gaz naturelPréparationduplandetravail Canalisation de gazDébit thermique des brûleurs Détendeur de gazInstructions Dinstallation Déballagede lacuisinièreMesurespourunehauteurappropriée Réglage despieds de nivellementInstallation de la brideantibasculement Vérificationdelemplacement de labride Antibasculement Retraitdutiroir-réchaudRéglage del’aplomb delacuisinière Raccordement à la canalisation degazInstallée sur le brûleur avant gauche Raccordement typique par raccord flexibleCuisinière encastrée Compléter le raccordemantSystème dallumageélectronique Allumage initial et réglages des flammesBrûleur à flamme TripleTier Si le brûleur ne sallume pas correctementRéinstallationdes grillesdufouret Dutiroir-réchaud AcheverlinstallationConversions Pour Changement DE GAZ Conversion pourlalimentationaupropaneConversion des brûleurs standard de la table de cuisson Important Ne pas enlever le détendeurDétendeur Enlever la plaque associée au gicleur externe Conversionpourlalimentation augaz naturel Chiffre gravé Holes in bracket Trous dans la bride All rights reserved

W10154991A specifications

The KitchenAid W10154991A is a versatile kitchen appliance designed to simplify meal preparation while enhancing culinary creativity. This food processor is equipped with innovative features and technologies that make it an essential addition to any modern kitchen.

One of the main features of the W10154991A is its powerful motor, which allows for quick and efficient processing of various ingredients. Whether you're chopping vegetables, shredding cheese, or mixing dough, this food processor can handle a wide range of tasks with ease. The motor's robust performance ensures that you can complete your cooking projects in a fraction of the time compared to using manual methods.

Another significant characteristic of the KitchenAid W10154991A is its variety of attachments and blades. The food processor comes equipped with multiple blades for different functions, including slicing, shredding, and chopping. This versatility enables users to achieve the desired texture and consistency for their recipes, all with one appliance. The included attachments are designed for easy installation and removal, making the transition between tasks seamless.

The design of the W10154991A also speaks to its user-friendly nature. It features a large capacity bowl, allowing you to process larger quantities of ingredients at once, which is ideal for meal prepping or when entertaining guests. The bowl is made from durable materials that can withstand the rigors of daily use while remaining easy to clean, as many parts are dishwasher safe.

Safety is a priority in the design of the KitchenAid W10154991A. It includes a safety lock feature that ensures the processor will not operate unless the bowl and lid are correctly secured. This feature gives users peace of mind while using the appliance and helps prevent accidents in the kitchen.

In terms of technology, the KitchenAid W10154991A employs a straightforward control panel that includes several speed settings. This means you can select the perfect speed for the task at hand, whether you need a gentle pulse or a steady chop. The intuitive design of the control panel makes it accessible for cooks of all skill levels.

In conclusion, the KitchenAid W10154991A food processor is an excellent investment for anyone looking to enhance their cooking experience. With its powerful motor, versatile attachments, user-friendly design, and safety features, this appliance stands out in the crowded market of kitchen gadgets. It empowers users to explore their culinary potential while simplifying time-consuming tasks in the kitchen.
Top Page Image Contents