KitchenAid W10154991A GAS Conversions, LPGas Conversion, To Convert Gas Pressure Regulator

Page 19

If range does not operate, check the following:

Household fuse is intact and tight, or circuit breaker has not tripped.

Gas valves are turned to the “open” position.

If the gas supply line shutoff valve is open, press the OFF button on the oven control panel and contact a qualified technician.

Electrical supply is connected.

See “Troubleshooting” in the Use and Care Guide.

When the range has been on for 5 minutes, check for heat. If range is cold, turn off the range and contact a qualified technician.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas; or from LP gas to Natural gas must be done by a qualified installer.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

LPGas Conversion

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

To Convert Gas Pressure Regulator

1.Turn manual shutoff valve to the “closed” position.

2.Unplug range or disconnect power.

B

A

C

A. To range

B. Manual shutoff valve “closed“ position

C. Gas supply line

3.Remove warming drawer. See the “Remove Warming Drawer” section for instructions. Locate gas pressure regulator at rear of warming drawer compartment.

4.Remove access cover from the gas pressure regulator.

A

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

Gas pressure regulator

5.Remove the access cap by using a wrench, turning the access cap counterclockwise.

6.Remove sprint retainer from the cap by pushing against the flat side of the spring retainer. Look at the spring retainer to locate the “NAT” or “LP” position.

7.Turn over the spring retainer so the “LP” is showing on the bottom.

8.Snap the spring retainer back into the cap.

19

Image 19
Contents W10154991A DE 30 76,2 CMTable DES Matières Range SafetyWhat to do if YOU Smell GAS ToolsandParts Installation RequirementsLocation Requirements Slide-in Range Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Mobile home installations requireFreestanding Ranges Installation ClearancesSlide-In Ranges Electrical Requirements U.S.A.Only If connecting to a 4-wire systemIf connecting to a 3-wire system Local codes may permit the use of a UL listed, 3-wireGas Supply Line Electrical Requirements -Canada OnlyGas Supply Requirements Type of GasGas Pressure Regulator Gas Supply Pressure TestingCountertopPreparation Burner Input RequirementsSlide-In Ranges Installation InstructionsUnpack Range MeasureforProperHeightInstallAnti-TipBracket Adjust LevelingLegsTo Remove Warming Drawer RemoveWarming DrawerVerifyAnti-Tip Bracket Location Level RangeElectrical Connection -U.S.A.Only Power Supply CordDirect Wire Style 1 Power supply cord strain reliefStyle 2 Direct wire strain relief Wire connection Power Supply CordWire Connection Direct Wire Direct Wire Installation Copper or Aluminum WireTypical rigid pipe connection Make Gas ConnectionComplete Connection Initial lighting and gas flame adjustmentsElectronicIgnitionSystem Typical flexible connectionReplace Oven RacksandWarmingDrawer Complete InstallationIf range does not operate, check the following GAS ConversionsLPGas Conversion To Convert Gas Pressure RegulatorGas orifice spuds are stamped with a number, marked with Reinstall the cap onto the regulatorTo Convert TripleTier Flame Burners on some models To Convert Standard Surface BurnersNaturalGas Conversion To Convert TripleTier Flame Burner on some models Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigencesd’emplacement Exigences D’INSTALLATIONOutillageetpièces Cuisinière encastrée Dimensions du produit Cuisinière autoportanteCuisinières autoportantes Dégagements de séparation à respecterCuisinières encastrées Gaz naturel Spécifications électriquesSpécifications del’alimentation engaz Type de gazDétendeur de gaz PréparationduplandetravailCanalisation de gaz Débit thermique des brûleursRéglage despieds de nivellement Instructions DinstallationDéballagede lacuisinière MesurespourunehauteurappropriéeInstallation de la brideantibasculement Raccordement à la canalisation degaz Vérificationdelemplacement de labride AntibasculementRetraitdutiroir-réchaud Réglage del’aplomb delacuisinièreCompléter le raccordemant Installée sur le brûleur avant gaucheRaccordement typique par raccord flexible Cuisinière encastréeSi le brûleur ne sallume pas correctement Système dallumageélectroniqueAllumage initial et réglages des flammes Brûleur à flamme TripleTierConversion pourlalimentationaupropane Réinstallationdes grillesdufouret Dutiroir-réchaudAcheverlinstallation Conversions Pour Changement DE GAZImportant Ne pas enlever le détendeur Conversion des brûleurs standard de la table de cuissonDétendeur Enlever la plaque associée au gicleur externe Conversionpourlalimentation augaz naturel Chiffre gravé Holes in bracket Trous dans la bride All rights reserved

W10154991A specifications

The KitchenAid W10154991A is a versatile kitchen appliance designed to simplify meal preparation while enhancing culinary creativity. This food processor is equipped with innovative features and technologies that make it an essential addition to any modern kitchen.

One of the main features of the W10154991A is its powerful motor, which allows for quick and efficient processing of various ingredients. Whether you're chopping vegetables, shredding cheese, or mixing dough, this food processor can handle a wide range of tasks with ease. The motor's robust performance ensures that you can complete your cooking projects in a fraction of the time compared to using manual methods.

Another significant characteristic of the KitchenAid W10154991A is its variety of attachments and blades. The food processor comes equipped with multiple blades for different functions, including slicing, shredding, and chopping. This versatility enables users to achieve the desired texture and consistency for their recipes, all with one appliance. The included attachments are designed for easy installation and removal, making the transition between tasks seamless.

The design of the W10154991A also speaks to its user-friendly nature. It features a large capacity bowl, allowing you to process larger quantities of ingredients at once, which is ideal for meal prepping or when entertaining guests. The bowl is made from durable materials that can withstand the rigors of daily use while remaining easy to clean, as many parts are dishwasher safe.

Safety is a priority in the design of the KitchenAid W10154991A. It includes a safety lock feature that ensures the processor will not operate unless the bowl and lid are correctly secured. This feature gives users peace of mind while using the appliance and helps prevent accidents in the kitchen.

In terms of technology, the KitchenAid W10154991A employs a straightforward control panel that includes several speed settings. This means you can select the perfect speed for the task at hand, whether you need a gentle pulse or a steady chop. The intuitive design of the control panel makes it accessible for cooks of all skill levels.

In conclusion, the KitchenAid W10154991A food processor is an excellent investment for anyone looking to enhance their cooking experience. With its powerful motor, versatile attachments, user-friendly design, and safety features, this appliance stands out in the crowded market of kitchen gadgets. It empowers users to explore their culinary potential while simplifying time-consuming tasks in the kitchen.