KitchenAid W10154991A installation instructions Adjust LevelingLegs, InstallAnti-TipBracket

Page 11

Adjust LevelingLegs

1.If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

2.Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

3.When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final position, check that the anti- tip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

InstallAnti-TipBracket

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard or hardboard.

1.Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back of this manual.

2.Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall, molding or cabinet.

3.Tape template into place.

4.If countertop is not flush with cabinet opening edge, align template with overhang.

If cabinet opening is wider than that specified in the “Location Requirements” section, adjust template so range will be centered in cabinet opening.

5.To mount anti-tip bracket to wood floor, drill two ¹⁄₈" (3.2 mm) holes at the positions marked on the bracket template. Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a ³⁄₁₆" (4.8 mm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Remove template from floor.

6.Tap plastic anchors into holes with a hammer.

7.Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store.

8.Move range close enough to opening to allow for final electrical connection. Remove shipping base, cardboard or hardboard from under range.

9.Move range into its final location making sure rear leveling leg slides into anti-tip bracket.

10.If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the “Location Requirements” section.

11.Continue installing your range using the following installation instructions.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents W10154991A DE 30 76,2 CMTable DES Matières Range SafetyWhat to do if YOU Smell GAS Location Requirements Installation RequirementsToolsandParts Slide-in Range Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Mobile home installations requireSlide-In Ranges Installation ClearancesFreestanding Ranges Electrical Requirements U.S.A.Only If connecting to a 4-wire systemIf connecting to a 3-wire system Local codes may permit the use of a UL listed, 3-wireGas Supply Line Electrical Requirements -Canada OnlyGas Supply Requirements Type of GasGas Pressure Regulator Gas Supply Pressure TestingCountertopPreparation Burner Input RequirementsSlide-In Ranges Installation InstructionsUnpack Range MeasureforProperHeightInstallAnti-TipBracket Adjust LevelingLegsTo Remove Warming Drawer RemoveWarming DrawerVerifyAnti-Tip Bracket Location Level RangeElectrical Connection -U.S.A.Only Power Supply CordDirect Wire Style 1 Power supply cord strain reliefStyle 2 Direct wire strain relief Wire connection Power Supply CordWire Connection Direct Wire Direct Wire Installation Copper or Aluminum WireTypical rigid pipe connection Make Gas ConnectionComplete Connection Initial lighting and gas flame adjustmentsElectronicIgnitionSystem Typical flexible connectionReplace Oven RacksandWarmingDrawer Complete InstallationIf range does not operate, check the following GAS ConversionsLPGas Conversion To Convert Gas Pressure RegulatorGas orifice spuds are stamped with a number, marked with Reinstall the cap onto the regulatorTo Convert TripleTier Flame Burners on some models To Convert Standard Surface BurnersNaturalGas Conversion To Convert TripleTier Flame Burner on some models Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutillageetpièces Exigences D’INSTALLATIONExigencesd’emplacement Cuisinière encastrée Dimensions du produit Cuisinière autoportanteCuisinières encastrées Dégagements de séparation à respecterCuisinières autoportantes Gaz naturel Spécifications électriquesSpécifications del’alimentation engaz Type de gazDétendeur de gaz PréparationduplandetravailCanalisation de gaz Débit thermique des brûleursRéglage despieds de nivellement Instructions DinstallationDéballagede lacuisinière MesurespourunehauteurappropriéeInstallation de la brideantibasculement Raccordement à la canalisation degaz Vérificationdelemplacement de labride AntibasculementRetraitdutiroir-réchaud Réglage del’aplomb delacuisinièreCompléter le raccordemant Installée sur le brûleur avant gaucheRaccordement typique par raccord flexible Cuisinière encastréeSi le brûleur ne sallume pas correctement Système dallumageélectroniqueAllumage initial et réglages des flammes Brûleur à flamme TripleTierConversion pourlalimentationaupropane Réinstallationdes grillesdufouret Dutiroir-réchaudAcheverlinstallation Conversions Pour Changement DE GAZDétendeur Conversion des brûleurs standard de la table de cuissonImportant Ne pas enlever le détendeur Enlever la plaque associée au gicleur externe Conversionpourlalimentation augaz naturel Chiffre gravé Holes in bracket Trous dans la bride All rights reserved

W10154991A specifications

The KitchenAid W10154991A is a versatile kitchen appliance designed to simplify meal preparation while enhancing culinary creativity. This food processor is equipped with innovative features and technologies that make it an essential addition to any modern kitchen.

One of the main features of the W10154991A is its powerful motor, which allows for quick and efficient processing of various ingredients. Whether you're chopping vegetables, shredding cheese, or mixing dough, this food processor can handle a wide range of tasks with ease. The motor's robust performance ensures that you can complete your cooking projects in a fraction of the time compared to using manual methods.

Another significant characteristic of the KitchenAid W10154991A is its variety of attachments and blades. The food processor comes equipped with multiple blades for different functions, including slicing, shredding, and chopping. This versatility enables users to achieve the desired texture and consistency for their recipes, all with one appliance. The included attachments are designed for easy installation and removal, making the transition between tasks seamless.

The design of the W10154991A also speaks to its user-friendly nature. It features a large capacity bowl, allowing you to process larger quantities of ingredients at once, which is ideal for meal prepping or when entertaining guests. The bowl is made from durable materials that can withstand the rigors of daily use while remaining easy to clean, as many parts are dishwasher safe.

Safety is a priority in the design of the KitchenAid W10154991A. It includes a safety lock feature that ensures the processor will not operate unless the bowl and lid are correctly secured. This feature gives users peace of mind while using the appliance and helps prevent accidents in the kitchen.

In terms of technology, the KitchenAid W10154991A employs a straightforward control panel that includes several speed settings. This means you can select the perfect speed for the task at hand, whether you need a gentle pulse or a steady chop. The intuitive design of the control panel makes it accessible for cooks of all skill levels.

In conclusion, the KitchenAid W10154991A food processor is an excellent investment for anyone looking to enhance their cooking experience. With its powerful motor, versatile attachments, user-friendly design, and safety features, this appliance stands out in the crowded market of kitchen gadgets. It empowers users to explore their culinary potential while simplifying time-consuming tasks in the kitchen.
Top Page Image Contents