KitchenAid Instant Hot Hot Water Dispenser Screw. Bracket will form a y when

Page 7

Installation Instructions cont.

NOTE: Do NOT plug power supply cord into outlet.

4.Lay spout assembly on flat surface with coiled tubing facing up. Using one hand to hold tubing just below spout, carefully straighten

gasket

tubing with other hand. Slide gasket over tubing so that lip side of gasket is seated into base of spout.

 

 

5.Loosen square nut until it is

Hold nut, bracket, gasket and tubing

 

 

flush with end of the mounting screw.

in position and insert into hole in sink

 

 

Tip spout bracket against mounting

or counter.

mounting

 

screw. (Bracket will form a “y” when

 

screw

 

in the correct position.)

 

 

 

square

bracket

nut

 

6.Pull up on spout body to keep tension on spout mounting bracket and nut. Tighten screw inside the spout until spout is securely in position. Do not overtighten. Snap on On/Off Cap.

off position

2-1/4"

(5.7 cm)

bracket

7.Position tank vertically beneath spout so that flexible tubing from spout reaches center stainless tubing on tank, and tank touches wall. Use a pencil to mark on the wall where the top of tank needs to be located. Set tank aside. Mark a second line 2-1/4" (5.7 cm) below the first line.

Note: The tank must be positioned so that the flexible tubing to the faucet does not kink.

Position mounting bracket on wall so that bottom of mounting bracket is even with the lower line. Use two screws (and plastic anchors if attaching to dry wall) to fasten mounting bracket to wall. Hang tank on bracket.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Thank you for buying a KitchenAid appliance Record your model’s informationHot Water Dispenser Safety Table of ContentsHow your hot water dispenser works Parts and FeaturesBefore You Start Parts supplied Electrical requirementsWater supply requirements Tools and materials neededNumbers 15. correspond To steps Installation InstructionsScrew. Bracket will form a y when Clamp. Make sure flexible tubing Do Not lengthen, twist or tightly Bend tubingDoes not kink Lower water temperature Dispensing hot water Using Your Hot Water DispenserBefore using the first time Temperature controlFor short periods 2-30 days of nonuse Cleaning the spout screenCaring For Your Hot Water Dispenser Energy-saving tips and preparation for periods NonuseBefore calling for service TroubleshootingFor further assistance Requesting Assistance or ServiceIf you need assistance or service in U.S.A If you need replacement partsIf you need service If you need assistance or service in CanadaKitchenAid Canada Appliance Service Consumer Services Installation Instant HOT* Water Dispenser WarrantyPage Inscrivez les renseignements concernant votre modèle Sécurité du distributeur d’eau chaude Table des matièresFonctionnement de votre distributeur d’eau chaude Pièces et caractéristiquesVerticalement Comptoir ou de ’évier Avant de commencerAlimentation électrique Spécifications Avant de commencer suiteAlimentation en eau Spécifications Les chiffres de 15. repérage Correspondent aux étapes Instructions d’installationInstructions d’installation suite Veiller à ce que le tube flexible ne soit pas déformé Ne pas allonger les tubes, ni les vriller ou les plierOuverture Distribution d’eau chaude Commande de la températureUtilisation de votre distributeur d’eau chaude Avant l’utilisation initialePour une brève période de non-utilisation 2 à 30 jours Entretien de votre distributeur ’eau chaudeNettoyage du filtre du robinet Avant de contacter le service de dépannage DiagnosticProblème Solution Pour obtenir une assistance plus étendue Demande d’assistance ou de serviceDemande d’assistance ou de service aux É.-U Pour acheter des pièces de rechangeSi vous avez besoin de services de dépannage Demande d’assistance ou de service au CanadaPour plus d’assistance ’UN AN Garantie du distributeur d’eau chaude Instant HOT

Instant Hot Hot Water Dispenser specifications

The KitchenAid Instant Hot Water Dispenser revolutionizes the way we use hot water in our kitchens, providing convenience and efficiency for a variety of cooking and beverage preparation tasks. This innovative appliance is designed to deliver instant boiling water, eliminating the wait time associated with traditional kettle boiling or stovetop heating.

One of the standout features of the KitchenAid Instant Hot Water Dispenser is its rapid heating technology. It boasts a powerful heating element that can quickly bring water to a rolling boil in a matter of seconds. Users can enjoy hot water for tea, coffee, pasta, or even instant oatmeal without the hassle of waiting around. The ability to dispense hot water on demand not only saves time but also enhances the overall cooking experience.

The dispenser features an ergonomic handle and a sleek design that seamlessly integrates into your kitchen decor. With a variety of finishes available, including polished chrome, brushed nickel, and a range of stylish colors, it can complement any aesthetic while providing functionality. The user-friendly controls allow for easy operation, and the swivel spout adds further convenience when filling pots or cups.

Another important characteristic of the KitchenAid Instant Hot Water Dispenser is its safety features. The unit is equipped with a safety lock to prevent accidental dispensing, making it suitable for households with children. Additionally, the dispenser's tank is insulated to ensure that it maintains water temperature while minimizing energy loss.

The dispenser also includes a built-in filtration system that ensures the water quality is pure and free from impurities. This is crucial for creating the best-tasting beverages and meals, enhancing the health aspect of your culinary endeavors.

The installation process is straightforward, as the unit connects easily to both power and water supply lines. For those who enjoy versatility in their kitchen, KitchenAid's Instant Hot Water Dispenser is compatible with most sinks and countertops.

With its array of features, advanced technology, and thoughtful design, the KitchenAid Instant Hot Water Dispenser stands as an essential kitchen appliance for anyone looking to streamline their cooking processes and enhance their beverage preparation routine. Its practical benefits combined with its stylish look make it a worthwhile investment for modern kitchens.
Top Page Image Contents