KitchenAid Instant Hot Hot Water Dispenser Electrical requirements, Water supply requirements

Page 5

Before You Start cont.

Tools and materials needed

ruler or measuring tape

pliers pencil

gloves

flat-blade screwdriver

safety glasses

tubing cutter

1/4" (6.4 mm) drill bit

hand or electric drill

open-end wrench(es) to fit saddle valve

1/4" (6.4 mm) O.D. copper tubing

bucket or pan

2 mounting bracket screws (and

2 plastic anchors if attaching to dry wall)

Saddle valve kit to fit

water supply line

Kit must meet all local codes and ordinances.

Parts supplied

Remove parts from packages. Check that all parts were included.

Electrical requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A 120-volt, 60-Hz, AC-only 15- or 20- ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your hot water dispenser be provided. Use an outlet that cannot be turned on/off by a switch.

Water supply requirements

3-prong ground-type outlet

3-prong ground plug

ground prong

power supply cord

Recommended ground method

For your personal safety, the hot water dispenser must be grounded. This appliance is equipped with a power supply cord having a 3-prong ground plug. To minimize possible shock hazard, the cord must be plugged into mating, 3-prong, ground- type outlet, grounded in accordance with all national and local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have a properly grounded, 3-prong outlet installed by a qualified electrician.

gasket

spout assembly

If local codes permit, the hot water dispenser feed line should be connected to the cold water supply line using a saddle tapping valve.

If this unit is replacing a hot water dispenser connected to a hot water supply, the existing connection may be used.

clamp

tank mounting bracket

tank

Important: If local codes Do Not permit the use of saddle valves, special feed valves can be obtained from your local plumbing supply distributor.

Connection to hot water line is not recommended. Energy will be wasted in heating the water twice and the magnesium rod used in household heating may produce a “rotten egg” taste.

A water filter is recommended if your water supply contains sand, grit or other particles. If a filter is used, the water pressure to the dispenser should not drop below 20 psi (138 kPa).

5

Image 5
Contents Thank you for buying a KitchenAid appliance Record your model’s informationHot Water Dispenser Safety Table of ContentsHow your hot water dispenser works Parts and FeaturesBefore You Start Water supply requirements Electrical requirementsTools and materials needed Parts suppliedNumbers 15. correspond To steps Installation InstructionsScrew. Bracket will form a y when Does not kink Do Not lengthen, twist or tightly Bend tubingClamp. Make sure flexible tubing Lower water temperature Before using the first time Using Your Hot Water DispenserTemperature control Dispensing hot waterCaring For Your Hot Water Dispenser Cleaning the spout screenEnergy-saving tips and preparation for periods Nonuse For short periods 2-30 days of nonuseBefore calling for service TroubleshootingIf you need assistance or service in U.S.A Requesting Assistance or ServiceIf you need replacement parts For further assistanceKitchenAid Canada Appliance Service Consumer Services If you need assistance or service in CanadaIf you need service Installation Instant HOT* Water Dispenser WarrantyPage Inscrivez les renseignements concernant votre modèle Sécurité du distributeur d’eau chaude Table des matièresFonctionnement de votre distributeur d’eau chaude Pièces et caractéristiquesVerticalement Comptoir ou de ’évier Avant de commencerAlimentation en eau Spécifications Avant de commencer suiteAlimentation électrique Spécifications Les chiffres de 15. repérage Correspondent aux étapes Instructions d’installationInstructions d’installation suite Veiller à ce que le tube flexible ne soit pas déformé Ne pas allonger les tubes, ni les vriller ou les plierOuverture Utilisation de votre distributeur d’eau chaude Commande de la températureAvant l’utilisation initiale Distribution d’eau chaudeNettoyage du filtre du robinet Entretien de votre distributeur ’eau chaudePour une brève période de non-utilisation 2 à 30 jours Problème Solution DiagnosticAvant de contacter le service de dépannage Demande d’assistance ou de service aux É.-U Demande d’assistance ou de servicePour acheter des pièces de rechange Pour obtenir une assistance plus étenduePour plus d’assistance Demande d’assistance ou de service au CanadaSi vous avez besoin de services de dépannage ’UN AN Garantie du distributeur d’eau chaude Instant HOT

Instant Hot Hot Water Dispenser specifications

The KitchenAid Instant Hot Water Dispenser revolutionizes the way we use hot water in our kitchens, providing convenience and efficiency for a variety of cooking and beverage preparation tasks. This innovative appliance is designed to deliver instant boiling water, eliminating the wait time associated with traditional kettle boiling or stovetop heating.

One of the standout features of the KitchenAid Instant Hot Water Dispenser is its rapid heating technology. It boasts a powerful heating element that can quickly bring water to a rolling boil in a matter of seconds. Users can enjoy hot water for tea, coffee, pasta, or even instant oatmeal without the hassle of waiting around. The ability to dispense hot water on demand not only saves time but also enhances the overall cooking experience.

The dispenser features an ergonomic handle and a sleek design that seamlessly integrates into your kitchen decor. With a variety of finishes available, including polished chrome, brushed nickel, and a range of stylish colors, it can complement any aesthetic while providing functionality. The user-friendly controls allow for easy operation, and the swivel spout adds further convenience when filling pots or cups.

Another important characteristic of the KitchenAid Instant Hot Water Dispenser is its safety features. The unit is equipped with a safety lock to prevent accidental dispensing, making it suitable for households with children. Additionally, the dispenser's tank is insulated to ensure that it maintains water temperature while minimizing energy loss.

The dispenser also includes a built-in filtration system that ensures the water quality is pure and free from impurities. This is crucial for creating the best-tasting beverages and meals, enhancing the health aspect of your culinary endeavors.

The installation process is straightforward, as the unit connects easily to both power and water supply lines. For those who enjoy versatility in their kitchen, KitchenAid's Instant Hot Water Dispenser is compatible with most sinks and countertops.

With its array of features, advanced technology, and thoughtful design, the KitchenAid Instant Hot Water Dispenser stands as an essential kitchen appliance for anyone looking to streamline their cooking processes and enhance their beverage preparation routine. Its practical benefits combined with its stylish look make it a worthwhile investment for modern kitchens.