KitchenAid Instant Hot Hot Water Dispenser installation instructions Lower water temperature

Page 9

Installation Instructions cont.

 

13.Connect water supply line

NOTE: If you need to remove tubing,

 

from saddle valve to spout copper

push down on collet. Pull tubing out

water supply

tubing with the factory-assembled

of quick-connect fitting.

line

quick-connect fitting. Push water

 

quick-connect

supply line tubing straight into fitting

 

as far as it will go. Pull on tubing.

 

fitting

 

 

The tubing should not come out

 

 

when properly installed. Turn the

 

copper

saddle valve handle counterclockwise

 

tubing

to open water line.

 

saddle valve

NOTE: Do NOT plug power supply cord into outlet.

14.Turn Temperature Control counterclockwise to “Off” position.

On

15.Push down and turn the

 

 

On/Off Cap clockwise to open spout.

 

Hold cap open to fill tank (about 1

 

minute). When tank is full, water will

 

flow from spout. Release cap.

NOTE: Turn Temperature Control to “Off” position before plugging hot water dispenser into power supply. If tank is empty and thermostat is in an “On” position when the

power supply cord is connected, the heater will overheat causing an unpleasant taste, black specks in the water, and permanent damage to the heater seals.

16.Plug power supply cord into grounded 3-prong outlet.

Turn Temperature Control clockwise to highest position.

Water in tank will reach maximum temperature in approximately

15 minutes.

When water is heating, you may hear gurgling noises coming from the tank. There may also be some spitting or

hot water flow from the faucet. This is normal for the initial heat-up of the dispenser.

Turn Temperature Control to lower temperature setting if you notice vapor or hear boiling noise.

NOTE: Temperature Control controls tank heater, not water delivery. Rotate Temperature Control clockwise to raise water temperature, counterclockwise to

lower water temperature.

9

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Thank you for buying a KitchenAid appliance Record your model’s informationHot Water Dispenser Safety Table of ContentsHow your hot water dispenser works Parts and FeaturesBefore You Start Water supply requirements Electrical requirementsTools and materials needed Parts suppliedNumbers 15. correspond To steps Installation InstructionsScrew. Bracket will form a y when Do Not lengthen, twist or tightly Bend tubing Clamp. Make sure flexible tubingDoes not kink Lower water temperature Before using the first time Using Your Hot Water DispenserTemperature control Dispensing hot waterCaring For Your Hot Water Dispenser Cleaning the spout screenEnergy-saving tips and preparation for periods Nonuse For short periods 2-30 days of nonuseBefore calling for service TroubleshootingIf you need assistance or service in U.S.A Requesting Assistance or ServiceIf you need replacement parts For further assistanceIf you need assistance or service in Canada If you need serviceKitchenAid Canada Appliance Service Consumer Services Installation Instant HOT* Water Dispenser WarrantyPage Inscrivez les renseignements concernant votre modèle Sécurité du distributeur d’eau chaude Table des matièresFonctionnement de votre distributeur d’eau chaude Pièces et caractéristiquesVerticalement Comptoir ou de ’évier Avant de commencerAvant de commencer suite Alimentation électrique SpécificationsAlimentation en eau Spécifications Les chiffres de 15. repérage Correspondent aux étapes Instructions d’installationInstructions d’installation suite Veiller à ce que le tube flexible ne soit pas déformé Ne pas allonger les tubes, ni les vriller ou les plierOuverture Utilisation de votre distributeur d’eau chaude Commande de la températureAvant l’utilisation initiale Distribution d’eau chaudeEntretien de votre distributeur ’eau chaude Pour une brève période de non-utilisation 2 à 30 joursNettoyage du filtre du robinet Diagnostic Avant de contacter le service de dépannageProblème Solution Demande d’assistance ou de service aux É.-U Demande d’assistance ou de servicePour acheter des pièces de rechange Pour obtenir une assistance plus étendueDemande d’assistance ou de service au Canada Si vous avez besoin de services de dépannagePour plus d’assistance ’UN AN Garantie du distributeur d’eau chaude Instant HOT

Instant Hot Hot Water Dispenser specifications

The KitchenAid Instant Hot Water Dispenser revolutionizes the way we use hot water in our kitchens, providing convenience and efficiency for a variety of cooking and beverage preparation tasks. This innovative appliance is designed to deliver instant boiling water, eliminating the wait time associated with traditional kettle boiling or stovetop heating.

One of the standout features of the KitchenAid Instant Hot Water Dispenser is its rapid heating technology. It boasts a powerful heating element that can quickly bring water to a rolling boil in a matter of seconds. Users can enjoy hot water for tea, coffee, pasta, or even instant oatmeal without the hassle of waiting around. The ability to dispense hot water on demand not only saves time but also enhances the overall cooking experience.

The dispenser features an ergonomic handle and a sleek design that seamlessly integrates into your kitchen decor. With a variety of finishes available, including polished chrome, brushed nickel, and a range of stylish colors, it can complement any aesthetic while providing functionality. The user-friendly controls allow for easy operation, and the swivel spout adds further convenience when filling pots or cups.

Another important characteristic of the KitchenAid Instant Hot Water Dispenser is its safety features. The unit is equipped with a safety lock to prevent accidental dispensing, making it suitable for households with children. Additionally, the dispenser's tank is insulated to ensure that it maintains water temperature while minimizing energy loss.

The dispenser also includes a built-in filtration system that ensures the water quality is pure and free from impurities. This is crucial for creating the best-tasting beverages and meals, enhancing the health aspect of your culinary endeavors.

The installation process is straightforward, as the unit connects easily to both power and water supply lines. For those who enjoy versatility in their kitchen, KitchenAid's Instant Hot Water Dispenser is compatible with most sinks and countertops.

With its array of features, advanced technology, and thoughtful design, the KitchenAid Instant Hot Water Dispenser stands as an essential kitchen appliance for anyone looking to streamline their cooking processes and enhance their beverage preparation routine. Its practical benefits combined with its stylish look make it a worthwhile investment for modern kitchens.
Top Page Image Contents