KitchenAid Instant Hot Hot Water Dispenser Troubleshooting, Before calling for service

Page 12

Troubleshooting

Before calling for service...

If hot water dispenser does not operate, check these points first:

✓

Has circuit breaker tripped or

✓

Is the Temperature Control set

 

house fuse blown?

 

to the “Off” position?

 

 

 

Is power supply cord plugged

 

 

Has the water supply been

✓

 

✓

 

in?

 

 

turned off?

 

 

 

✓

Is the electrical outlet controlled by a switch?

If you need more help, check the chart below. This could save you the cost of a service call for a problem that is not covered by the warranty.

PROBLEM

CHECK THE FOLLOWING

Water is not hot.

 

 

Check that the circuit breaker is not tripped or the house fuse blown.

 

 

 

 

 

Check that power supply cord is plugged into electrical outlet.

 

 

 

 

 

 

Check if the electrical outlet is operated by a switch. The switch may

 

 

 

 

 

 

have turned power off.

 

 

 

Cold water in tank is still being heated. Wait 15 minutes and check

 

 

 

 

 

 

temperature again.

 

 

 

Check that the Temperature Control is set to the “Max” setting.

 

 

 

 

 

 

 

Vapor appears, dispenser makes boiling water noises, or water is too hot.

Adjust Temperature Control to a lower setting that eliminates the vapor or noise. If you live at a high altitude, you may need to lower the thermostat setting to keep water from boiling.

Hot water drips or sputters from spout.

Check that tubing is not bent or kinked.

Adjust Temperature Control to a lower setting that eliminates the drips or sputters.

Check that spout screen is not clogged. See “Caring For Your Hot Water Dispenser,” Page 11.

Check for proper installation of copper tubing from spout to storage tank and from spout to cold water line. See “Installation Instructions,” Pages 8-9.

Water does not flow from spout.

Check that water supply valve is open.

Check that spout screen is not clogged. See “Caring For Your Hot Water Dispenser,” Page 11.

If a water filter is used, check that water pressure to hot water dispenser is 20 psi (138 kPa) minimum.

Leaking saddle valve.

 

Tighten saddle valve clamp screws evenly and firmly. Keep both halves

 

 

 

 

of bracket parallel. Do Not crush water supply tubing.

Water has a “rotten egg” taste.

Hot water dispenser is attached to hot water line. Attach to cold water line.

Install a water filtration system on cold water line to dispenser.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Record your model’s information Thank you for buying a KitchenAid applianceTable of Contents Hot Water Dispenser SafetyParts and Features How your hot water dispenser worksBefore You Start Electrical requirements Water supply requirementsTools and materials needed Parts suppliedInstallation Instructions Numbers 15. correspond To stepsScrew. Bracket will form a y when Do Not lengthen, twist or tightly Bend tubing Clamp. Make sure flexible tubingDoes not kink Lower water temperature Using Your Hot Water Dispenser Before using the first timeTemperature control Dispensing hot waterCleaning the spout screen Caring For Your Hot Water DispenserEnergy-saving tips and preparation for periods Nonuse For short periods 2-30 days of nonuseTroubleshooting Before calling for serviceRequesting Assistance or Service If you need assistance or service in U.S.AIf you need replacement parts For further assistanceIf you need assistance or service in Canada If you need serviceKitchenAid Canada Appliance Service Consumer Services Instant HOT* Water Dispenser Warranty InstallationPage Inscrivez les renseignements concernant votre modèle Table des matières Sécurité du distributeur d’eau chaudePièces et caractéristiques Fonctionnement de votre distributeur d’eau chaudeAvant de commencer Verticalement Comptoir ou de ’évierAvant de commencer suite Alimentation électrique SpécificationsAlimentation en eau Spécifications Instructions d’installation Les chiffres de 15. repérage Correspondent aux étapesInstructions d’installation suite Ne pas allonger les tubes, ni les vriller ou les plier Veiller à ce que le tube flexible ne soit pas déforméOuverture Commande de la température Utilisation de votre distributeur d’eau chaudeAvant l’utilisation initiale Distribution d’eau chaudeEntretien de votre distributeur ’eau chaude Pour une brève période de non-utilisation 2 à 30 joursNettoyage du filtre du robinet Diagnostic Avant de contacter le service de dépannageProblème Solution Demande d’assistance ou de service Demande d’assistance ou de service aux É.-UPour acheter des pièces de rechange Pour obtenir une assistance plus étendueDemande d’assistance ou de service au Canada Si vous avez besoin de services de dépannagePour plus d’assistance Garantie du distributeur d’eau chaude Instant HOT ’UN AN

Instant Hot Hot Water Dispenser specifications

The KitchenAid Instant Hot Water Dispenser revolutionizes the way we use hot water in our kitchens, providing convenience and efficiency for a variety of cooking and beverage preparation tasks. This innovative appliance is designed to deliver instant boiling water, eliminating the wait time associated with traditional kettle boiling or stovetop heating.

One of the standout features of the KitchenAid Instant Hot Water Dispenser is its rapid heating technology. It boasts a powerful heating element that can quickly bring water to a rolling boil in a matter of seconds. Users can enjoy hot water for tea, coffee, pasta, or even instant oatmeal without the hassle of waiting around. The ability to dispense hot water on demand not only saves time but also enhances the overall cooking experience.

The dispenser features an ergonomic handle and a sleek design that seamlessly integrates into your kitchen decor. With a variety of finishes available, including polished chrome, brushed nickel, and a range of stylish colors, it can complement any aesthetic while providing functionality. The user-friendly controls allow for easy operation, and the swivel spout adds further convenience when filling pots or cups.

Another important characteristic of the KitchenAid Instant Hot Water Dispenser is its safety features. The unit is equipped with a safety lock to prevent accidental dispensing, making it suitable for households with children. Additionally, the dispenser's tank is insulated to ensure that it maintains water temperature while minimizing energy loss.

The dispenser also includes a built-in filtration system that ensures the water quality is pure and free from impurities. This is crucial for creating the best-tasting beverages and meals, enhancing the health aspect of your culinary endeavors.

The installation process is straightforward, as the unit connects easily to both power and water supply lines. For those who enjoy versatility in their kitchen, KitchenAid's Instant Hot Water Dispenser is compatible with most sinks and countertops.

With its array of features, advanced technology, and thoughtful design, the KitchenAid Instant Hot Water Dispenser stands as an essential kitchen appliance for anyone looking to streamline their cooking processes and enhance their beverage preparation routine. Its practical benefits combined with its stylish look make it a worthwhile investment for modern kitchens.
Top Page Image Contents