KitchenAid Instant Hot Hot Water Dispenser Do Not lengthen, twist or tightly Bend tubing

Page 8

Installation Instructions cont.

	NOTE: Do NOT plug power supply cord into outlet.
	8.Connect 1/4" (6.4 mm) spout	NOTE: If you need to remove tubing,
	tubing (longer tubing) to the rear	push down on collet. Pull tubing out
	quick-connect fitting on top of tank.	of quick-connect fitting.
quick-	Push tubing straight into fitting as far
quick-	as it will go. Pull on tubing. The
connect	tubing should not come out when
fitting	tubing should not come out when
	properly installed.
collet	Do Not lengthen, twist or tightly
	bend tubing.

	9.Connect flexible tubing from
	spout to center tank tubing using
	clamp. Make sure flexible tubing
	does not kink.
	The flexible tubing may be shortened
clamp	if necessary.
clamp

flexible tubing

10.Install saddle valve following kit instructions. If water supply line is not copper, shut off water supply and

drain line. Drill a 1/4" (6.4 mm) hole into water supply line for the saddle valve piercing pin.

closed

11.Turn saddle valve handle clockwise until lance pierces soft copper tubing and valve is firmly seated. If the water line is not copper, turn the saddle valve handle clockwise until the valve is firmly seated. The valve is now in the closed position.

Place a bucket under open end of water supply line. Turn on main water supply valve to pressurize cold water line. Check for leaks.

open

12.Slowly open saddle valve and flush line into bucket to remove any foreign material that may have been trapped in the supply line during saddle valve installation.

Close saddle valve.

8

Image 8

Contents Record your model’s information Thank you for buying a KitchenAid applianceTable of Contents Hot Water Dispenser SafetyParts and Features How your hot water dispenser worksBefore You Start Electrical requirements Water supply requirements Tools and materials needed Parts suppliedInstallation Instructions Numbers 15. correspond To stepsScrew. Bracket will form a y when Does not kink Do Not lengthen, twist or tightly Bend tubingClamp. Make sure flexible tubing Lower water temperature Using Your Hot Water Dispenser Before using the first timeTemperature control Dispensing hot waterCleaning the spout screen Caring For Your Hot Water DispenserEnergy-saving tips and preparation for periods Nonuse For short periods 2-30 days of nonuseTroubleshooting Before calling for serviceRequesting Assistance or Service If you need assistance or service in U.S.AIf you need replacement parts For further assistanceKitchenAid Canada Appliance Service Consumer Services If you need assistance or service in CanadaIf you need service Instant HOT* Water Dispenser Warranty InstallationPage Inscrivez les renseignements concernant votre modèle Table des matières Sécurité du distributeur d’eau chaudePièces et caractéristiques Fonctionnement de votre distributeur d’eau chaudeAvant de commencer Verticalement Comptoir ou de ’évierAlimentation en eau Spécifications Avant de commencer suiteAlimentation électrique Spécifications Instructions d’installation Les chiffres de 15. repérage Correspondent aux étapesInstructions d’installation suite Ne pas allonger les tubes, ni les vriller ou les plier Veiller à ce que le tube flexible ne soit pas déforméOuverture Commande de la température Utilisation de votre distributeur d’eau chaudeAvant l’utilisation initiale Distribution d’eau chaudeNettoyage du filtre du robinet Entretien de votre distributeur ’eau chaudePour une brève période de non-utilisation 2 à 30 jours Problème Solution DiagnosticAvant de contacter le service de dépannage Demande d’assistance ou de service Demande d’assistance ou de service aux É.-UPour acheter des pièces de rechange Pour obtenir une assistance plus étenduePour plus d’assistance Demande d’assistance ou de service au CanadaSi vous avez besoin de services de dépannage Garantie du distributeur d’eau chaude Instant HOT ’UN AN