Black & Decker EC70 manual Installing Your can Opener, Mounting Instructions

Page 4

Figure A1 - Flush Bottom

Figure A2 - Overhang Bottom

Figure B

Figure C

Cover

Do not install the Can Opener over another cook- ing or heating appliance or behind, under, or in front of an under-cabinet lighting fixture.

Unwind the cord and extend it to the nearest polarized or adapted outlet to be certain it will reach.

Allow about 5 inches (12.7 cm) to the right and left side between the Can Opener and any adjacent wall or appliance .

INSTALLING YOUR CAN OPENER

1.First determine if your cabinet has a flush bottom or an overhang bottom (see Figures A1 and A2). If your cabinet has a Flush Bottom—a flat level surface—skip to the “Mounting Instructions”.

2.If your cabinet has an Overhang Bottom—a lip extending below the bottom of the cabinet front— measure the overhang with a ruler. You may have to use a wooden shim (a piece of wood that fits between the Cabinet and the Bracket) if the lip extends 2 inches (5.1 cm) or more below the cabinet bottom.

3.Use the Mounting Bracket as your guide to locate and drill holes in the shim for the screws to pass through. At least 1/2” (1.3 cm) of the screw must be visible once it is dropped through the cabi- net floor and the shim to provide secure mounting. You may need screws longer than those provided.

4.If your overhang is less than 2 inches (5.1 cm), you can avoid using a shim by simply mounting the Bracket behind the overhang so that the can opener will be set back slightly from the front edge. See the mounting instructions below.

MOUNTING INSTRUCTIONS

1.Empty the bottom of your cabinet and clean the underside.

2.With the cabinet doors open, hold the Mounting Bracket up to the underside of the cabinet .(Figure B) For flush bottom cabinets, it is easiest to mount the can opener at the front edge of the cabinet; for cabinets with an overhang less than 2 inches (5.1 cm), set it back behind the overhang.

3.Use the Mounting Bracket and a pencil to mark the location of the three holes to be drilled on the bottom of the cabinet. Use a hammer and nail (or center punch) to tap in starter holes at your pencil marks.

4

Image 4
Contents Spacemaker Important Safeguards Electrical Cord Polarized PlugChoosing a Mounting Location Empty the bottom of your cabinet and clean the underside Installing Your can OpenerMounting Instructions To Open a can Ing on the rim. Figure FTo Open Bottles Can Opening TipsTo Open Bags Cleaning Your can Opener Service or RepairFull TWO-YEAR Warranty Unplug the can openerInstrucciones DE Seguridad EL Cable Electrico Enchufe PolarizadoDonde Instalar EL Abrelatas Como Instalar EL Abrelatas Como InstalarDesenrolle el cable, extiéndalo y asegúrese de Vacíe la parte inferior del gabinete y límpielo por debajoPara Abrir UNA Lata GuíaPara Abrir Botellas Consejos Para Abrir LAS LatasPara Abrir Bolsas Guia DE Cuidado Servicio O ReparacionesDOS Años Completos DE Garantia Desconecte la unidad antes de limpiarlaConserver CES Mesures Fiche Polarisée Choix DE L’EMPLACEMENTCordon Installation DE L’OUVRE-BOÎTE Instructions Relatives AU MontageUtilisation DE L’OUVRE-BOÎTE Figure E GuideUtilisation DE L’OUVRE-SAC Utilisation DU Décapsuleur’ouvre-sac se trouve à droite du support de montage Service OU Réparation Nettoyage DE L’OUVRE-BOÎTEGarantie Complète DE Deux ANS Débrancher l’ouvre-boîteCover