Frymaster FBKR18 Series, FBCR18 manual Caster/Leg Installation

Page 11

All electrically operated appliances must be grounded in accordance with all applicable national and local codes. A wiring diagram is located on the inside of the door. In the United States and Canada, the electrical supply must be 120VAC, 60 Hz. In other countries, refer to the rating plate on the inside of the door for proper voltages.

FCC COMPLIANCE

The user is cautioned that any changes or modifications to Frymaster computers not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equip- ment. Frymaster computers have been tested and found to comply with the limits for a Class A digi- tal device, pursuant to Part 15 of the FCC rules. While these devices are verified as Class A devices, they have been shown to meet the Class B limits. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ- ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com- munications. Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. If necessary, the user should consult the dealer or an experienced radio and television technician for additional suggestions.

The user may find the booklet “How to Identify and Resolve Radio-TV Interference Problems” help- ful. It is prepared by the Federal Communications Commission and is available from the U.S. Gov- ernment Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

2.2Caster/Leg Installation

Depending upon the specific configuration ordered, your unit may have been shipped without in- stalled casters or legs. If casters or legs are installed, you may skip this section and proceed to Sec- tion 2.3, Pre-Connection Preparations.

If your unit requires the installation of casters/legs, install them in accordance with the in- structions included in your accessory package.

2.3Pre-Connection Preparations

DANGER

Do not connect this equipment to the gas supply before completing each step in this section.

After the unit has been positioned in the area where it will be used, ensure the following has been accomplished before connecting the unit to the gas supply:

1.Adequate means must be provided to limit the movement of this equipment without depending upon the gas line connections. If a flexible gas hose is used, a restraining cable must be connected at all times when the equipment is in use. The restraining cable and installation instructions are packed with the flexible hose in the accessories box that was shipped with your unit.

2-3

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Hour Service Hotline Canada Page FBCR18 & FBKR18 Series GAS Rethermalizers Table of Contents Operator Troubleshooting Applicability and Validity Parts Ordering and Service InformationEquipment Description Safety InformationInstallation, Operating, and Service Personnel What to do if your equipment arrives damaged Shipping Damage Claim ProcedureDefinitions General Installation Requirements National Code Requirements Caster/Leg Installation Incoming Gas Pressures GAS Connections and Pipe Sizes Converting to Another Gas Type FBCR18 Series Computer FBCR18 Series ComputerProgramming the FBCR18 Series Computer FBKR18 Series Computer Programming the FBKR18 Series Computer Page Operating the FBKR18 Series Rethermalizer FBKR18 Computer Display Messages Honeywell Shutting the Rethermalizer Down Inspect Rethermalizer and Accessories for Damage Daily Checks and ServicesSemi-Annual Checks and Services Quarterly Checks and ServicesCheck Burner Manifold Pressure Burner Manifold Gas Pressures Page Troubleshooting Guides Water not HEATING. Autofill Worked Properly Burners do Not Light Problem is beyond scope of operator troubleshooting Replacing the Computer or Computer Wiring Harness Functional Description Computers Temperature Probe Measuring Flame Current Cleaning the Gas Valve Vent TubeChecking the Burner Manifold Gas Pressure Replacing the Interface Board Replacing the Temperature ProbeReplacing the Gas Valve Replacing an Ignitor AssemblyReplacing an Ignition Module Replacing the Combustion Air BlowerReplacing a Burner Assembly Replacing the Cookpot Troubleshooting and Problem IsolationIgnition Failures Improper Burner Functioning Incoming Gas PressuresPage Computer-Related Problems Improper Temperature ControlTroubleshooting the Gas Valve Troubleshooting the 24 VAC Circuit 24VAC Circuit Troubleshooting the Temperature Probe Probe Resistance Chart FBKR18 only Simplified Wiring DiagramsInterface Board Computer Burner System Components FBCR18 & FBKR18 Series GAS Rethermalizers Parts ListSide, Cabinet, CRS for S/S units, use Cabinetry and Associated ComponentsComputer, Component Box Assembly, and Associated Parts Cookpot and Associated Parts Gas Supply Components Nipple, Close, 1 NPT Plumbing ComponentsService Hotline

FBKR18 Series, FBCR18 specifications

The Frymaster FBKR18 and FBCR18 series are among the industry’s leading commercial fryers, designed to meet the rigorous demands of high-volume food service operations. These advanced fryers are built to provide exceptional frying performance, energy efficiency, and ease of use, making them ideal for restaurants, cafeterias, and catering operations.

One of the standout features of the Frymaster FBKR18 and FBCR18 series is their innovative cooking technology. These fryers incorporate the patented Frymaster oil management system, which helps to improve oil life while ensuring consistent food quality. The system includes an advanced filtration mechanism that can be operated manually or automatically, allowing for quick and efficient oil changes while minimizing downtime.

Another key characteristic of the FBKR18 and FBCR18 series is their impressive capacity. With the ability to hold up to 18 pounds of oil, these fryers can accommodate large batches of food, making them perfect for busy kitchens. The fryers come equipped with dual fry pots, allowing operators to prepare multiple menu items simultaneously without flavor transfer.

Energy efficiency is also a critical aspect of the Frymaster FBKR18 and FBCR18 series. These fryers utilize a high-efficiency burner design that reduces energy consumption while still delivering sufficient cooking power. This feature not only helps to lower utility costs but also contributes to a more environmentally friendly operation.

The design of the FBKR18 and FBCR18 series is focused on ease of use and safety. The fryers feature a user-friendly digital control panel that allows operators to easily monitor and adjust cooking temperatures. Additionally, the fryers are equipped with built-in safety features, such as automatic shut-off mechanisms, ensuring safe operation even in high-demand situations.

Durability is another hallmark of these fryers. Constructed from high-quality stainless steel, the FBKR18 and FBCR18 series are built to withstand the rigors of daily use in commercial kitchens. Their robust design not only ensures longevity but also simplifies cleaning and maintenance.

In summary, the Frymaster FBKR18 and FBCR18 series fryers combine advanced cooking technology, impressive capacity, energy efficiency, and user-friendly design to meet the needs of busy food service operations. With their durability and high performance, these fryers stand out as excellent choices for chefs aiming to achieve culinary excellence.
Top Page Image Contents