Frymaster Protector Series Converting to another Gas Type, CE GAS Conversion Instructions

Page 16

2.5Converting to another Gas Type

DANGER

This appliance was configured at the factory for a specific type of gas. Converting from one type of gas to another requires the installation of specific gas-conversion compo- nents. Conversion instructions are included with conversion kits.

Switching to a different type of gas without installing the proper conversion components may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A GAS SUPPLY FOR WHICH IT IS NOT CONFIGURED!

Conversion of this appliance from one type of gas to another should only be performed by qualified, licensed, and authorized installation or service personnel, as defined in Section 1.7 of this manual.

Protector® Series gas fryers manufactured for non-CE countries use different burners for each type gas. The burners in fryers built for Propane gas have a special gray-colored coating on the burner tiles to enable them to withstand the higher caloric value of the Propane gas. Burners designed for use in propane units may be used in natural gas applications, but not vice versa.

Non-CE Gas Conversion Kits

Natural Gas to Propane (LP) Gas

Propane (LP) Gas to Natural Gas

Full Vat: Part Number 826-2527

Full Vat: Part Number 826-2528

Dual Vat: Part Number 826-2529

Dual Vat: Part Number 826-2530

 

 

 

 

Units manufactured for export to CE countries are equipped with “universal” burners that may be used with either Natural (G20, G25) gas or Butane (G30) and Propane (G31) gasses.

CE Gas Conversion Kits for Units with Gas Valve 810-1715

G20 or G25 (Natural) to G30 or G31 Gas:

G30 or G31 to G20 or G25 (Natural) Gas:

Part Number 826-1196

Part Number 826-1197

 

 

 

 

CE GAS CONVERSION INSTRUCTIONS

1.Between G20- and G25-type Natural Gas, adjust the gas pressure at the regulator. (Refer to the CE Standard Burner Manifold Gas Pressure Chart.) Do not change the orifice.

2.Between a 2nd family (G20 or G25) and a 3rd family gas (G30 Butane or G31 Propane):

a.Change the orifices.

b.Adjust the manifold pressure.

3.Remove the old rating plate and return to Frymaster. Affix the new rating plate included with the conversion kit in place of the old rating plate stating the gas has been converted.

4.If the destination language changes, replace the rating plate. Call your local service agency or KES for a label kit. The language of reference will be on the corner of the label.

2-8

Image 16
Contents Hour Service Hotline Protector Series GAS FryersCanada Iii Safety Information Applicability and ValidityComputer Information for the CM7 Computers European Community CE Specific InformationEquipment Description Installation, Operating, and Service PersonnelDefinitions Parts Ordering and Service Information Shipping Damage Claim ProcedureWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE General Installation Requirements Do not block the area around the base or under the fryersNational Code Requirements Caster/Leg Installation Electrical Grounding RequirementsNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures Converting to another Gas Type CE GAS Conversion InstructionsPositioning the Fryer Protector Series GAS Fryer Operating Instructions Finding Your WAY around the Protector Series GAS FryerController Operation and Programming Press the computer ON/OFF switch to the OFF position Lighting the FryerBoiling Out the Frypot Shutting the Fryer DownInstall the Oil Reservoir Oil Attendant Automatic Top-OffPrepare the System for Use Routine Oil ChangesBulk Oil Systems Protector Series GAS Fryers CM7 Computer Instructions CM7 General InformationBasic Operation Cooking with Multi-Product Display FR Fries Cooking with Dedicated DisplayChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast CM7 Button Description and Functions Navigation ButtonsTemperature Conversion from F to C CM7 Menu Summary TreeAdding New Product Menu Items Storing Product Menu Items in Product ButtonsSetup Mode Programming Setup7378 12hrPage Page 10 CM7 Common Tasks 1650Page Sensitivity Storing Menu Items in Product Buttons Boil-Out Mode 1658Setpoint Temperature Page Manager Mode 4321To E-LOG E06 Ignition Failure Call TechnicianOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Cleaning ReassemblyDraining and Disposing of Waste Oil Fryer Preventative Maintenance Checks and Service Daily Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutMonthly Checks and Service Check Computer Magic 7 Set Point AccuracyBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Fryer Built-In Filtration SystemPage Protector Series GAS Fryers Operator Troubleshooting IntroductionTroubleshooting Fryers Computer and Heating Problems Problem Probable Causes Corrective ActionCorrective Action Probable CausesProblem Probable Causes Corrective Action Filtration ProblemsAuto Top-Off Problems Problem Probable CausesBasket Lift Problems Service Hotline

Protector Series specifications

The Frymaster Protector Series represents a significant advancement in commercial frying technology, designed to elevate both cooking efficiency and food quality while ensuring operational safety and consistency. With a focus on energy savings and ease of use, the Protector Series is tailored for establishments seeking high performance without compromising on their environmental responsibilities.

One of the standout features of the Frymaster Protector Series is its advanced temperature control technology. This series incorporates a precise digital thermostat that maintains optimal frying temperatures, allowing for consistent cooking results. Such accuracy minimizes oil degradation, extends oil life, and ultimately reduces frying costs. Coupled with the innovative oil filtration system, the Protector Series ensures that the oil remains clean, further enhancing food quality and flavor.

Another significant advancement in the Frymaster Protector Series is its improved heating elements. These elements are designed for rapid heat recovery, which means that after food is added to the fryer, the oil temperature returns to cooking levels more quickly, which is vital for high-volume frying operations. The result is reduced cooking times and increased throughput, enabling kitchens to serve more customers efficiently.

Safety is also a primary consideration in the design of the Frymaster Protector Series. It includes several built-in safety features, such as automatic shut-off controls and advanced overheating protection, ensuring that operators can work confidently without fear of accidents. Additionally, the series is equipped with easy-to-read digital displays that provide real-time monitoring of oil temperatures and cooking times, improving both safety and operational precision.

The robust construction of the Frymaster Protector Series is another notable characteristic. Built with high-quality stainless steel, these fryers are designed to withstand the rigors of busy kitchen environments. Their sleek design not only adds a modern aesthetic but also facilitates cleaning and maintenance, ensuring that kitchens remain sanitary and compliant with health regulations.

In summary, the Frymaster Protector Series is engineered for excellence in performance, safety, and efficiency. Its combination of advanced technologies, superior temperature control, and built-in safety measures makes it a valuable asset for any commercial kitchen aiming to maximize productivity while delivering exceptional food quality. Whether for a small diner or a large restaurant chain, the Frymaster Protector Series stands as a trusted solution for frying needs.