Frymaster Protector Series Monthly Checks and Service, Check Computer Magic 7 Set Point Accuracy

Page 55

There are no periodic preventive maintenance checks and services required for your FootPrint Pro Filtration System other than daily cleaning of the filter pan with a solution of hot water and detergent.

If you notice that the system is pumping slowly or not at all, verify that the filter pan screen is on the bottom of the filter pan, with the paper on top of the screen. (If the unit is equipped with a Magnasol filter screen rather than with the standard screen and paper system, verify that the O-ring on the bottom fitting of the screen in present and in good condition.) Verify that the two O-ring(s) on the fitting at the right front of the filter pan are present and in good condition.

6.3WEEKLY CHECKS AND SERVICE 6.3.1 Drain and Clean Frypot

DANGER

Never operate the appliance with an empty frypot. The frypot must be filled with water or oil before lighting the burners. Failure to do so will damage the frypot and may cause a fire.

6.3.2 Boiling Out the Frypot

After the fryer has been in use for a period of time, a hard film of caramelized oil will form on the inside of the frypot. This deposit must be periodically removed to maintain your fryer’s efficiency. See section 4.11 page 4-16 for instructions on boiling out the frypot.

6.4MONTHLY CHECKS AND SERVICE

6.4.1 Check Computer Magic 7 Set Point Accuracy

(This check applies only to units equipped with Computer Magic 7 Controllers.)

1.Insert a good-grade thermometer or pyrometer probe into the oil, with the end touching the fryer temperature-sensing probe.

2.When the computer display shows a series of four dashes “----” with no dot between the first and second dashes (indicating that the frypot contents are within the cooking range), press the switch once to display the temperature of the cooking oil as sensed by the temperature probe.

3.Press the switch twice to display the set point.

4.Note the temperature on the thermometer or pyrometer. All three readings should be within

± 5ºF (2ºC) of each other. If not, contact a Factory Authorized Service Center for assistance.

6-2

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Protector Series GAS Fryers Hour Service HotlineCanada Iii Applicability and Validity Safety InformationEuropean Community CE Specific Information Computer Information for the CM7 ComputersEquipment Description Installation, Operating, and Service PersonnelDefinitions Parts Ordering and Service Information Shipping Damage Claim ProcedureWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE Do not block the area around the base or under the fryers General Installation RequirementsNational Code Requirements Electrical Grounding Requirements Caster/Leg InstallationNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures CE GAS Conversion Instructions Converting to another Gas TypePositioning the Fryer Finding Your WAY around the Protector Series GAS Fryer Protector Series GAS Fryer Operating InstructionsController Operation and Programming Lighting the Fryer Press the computer ON/OFF switch to the OFF positionShutting the Fryer Down Boiling Out the FrypotRoutine Oil Changes Install the Oil ReservoirOil Attendant Automatic Top-Off Prepare the System for UseBulk Oil Systems CM7 General Information Protector Series GAS Fryers CM7 Computer InstructionsBasic Operation Cooking with Multi-Product Display Cooking with Dedicated Display FR FriesChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast Navigation Buttons CM7 Button Description and FunctionsStoring Product Menu Items in Product Buttons Temperature Conversion from F to CCM7 Menu Summary Tree Adding New Product Menu Items12hr Setup Mode ProgrammingSetup 7378Page Page 1650 10 CM7 Common TasksPage Sensitivity Storing Menu Items in Product Buttons 1658 Boil-Out ModeSetpoint Temperature Page E06 Ignition Failure Call Technician Manager Mode4321 To E-LOGOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Reassembly CleaningDraining and Disposing of Waste Oil Clean Fryer Cabinet Inside and Out Fryer Preventative Maintenance Checks and ServiceDaily Checks and Service Inspect Fryer and Accessories for DamageCheck Computer Magic 7 Set Point Accuracy Monthly Checks and ServiceBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Built-In Filtration System FryerPage Introduction Protector Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action Troubleshooting Fryers Computer and Heating ProblemsProbable Causes Corrective ActionFiltration Problems Problem Probable Causes Corrective ActionAuto Top-Off Problems Problem Probable CausesBasket Lift Problems Service Hotline

Protector Series specifications

The Frymaster Protector Series represents a significant advancement in commercial frying technology, designed to elevate both cooking efficiency and food quality while ensuring operational safety and consistency. With a focus on energy savings and ease of use, the Protector Series is tailored for establishments seeking high performance without compromising on their environmental responsibilities.

One of the standout features of the Frymaster Protector Series is its advanced temperature control technology. This series incorporates a precise digital thermostat that maintains optimal frying temperatures, allowing for consistent cooking results. Such accuracy minimizes oil degradation, extends oil life, and ultimately reduces frying costs. Coupled with the innovative oil filtration system, the Protector Series ensures that the oil remains clean, further enhancing food quality and flavor.

Another significant advancement in the Frymaster Protector Series is its improved heating elements. These elements are designed for rapid heat recovery, which means that after food is added to the fryer, the oil temperature returns to cooking levels more quickly, which is vital for high-volume frying operations. The result is reduced cooking times and increased throughput, enabling kitchens to serve more customers efficiently.

Safety is also a primary consideration in the design of the Frymaster Protector Series. It includes several built-in safety features, such as automatic shut-off controls and advanced overheating protection, ensuring that operators can work confidently without fear of accidents. Additionally, the series is equipped with easy-to-read digital displays that provide real-time monitoring of oil temperatures and cooking times, improving both safety and operational precision.

The robust construction of the Frymaster Protector Series is another notable characteristic. Built with high-quality stainless steel, these fryers are designed to withstand the rigors of busy kitchen environments. Their sleek design not only adds a modern aesthetic but also facilitates cleaning and maintenance, ensuring that kitchens remain sanitary and compliant with health regulations.

In summary, the Frymaster Protector Series is engineered for excellence in performance, safety, and efficiency. Its combination of advanced technologies, superior temperature control, and built-in safety measures makes it a valuable asset for any commercial kitchen aiming to maximize productivity while delivering exceptional food quality. Whether for a small diner or a large restaurant chain, the Frymaster Protector Series stands as a trusted solution for frying needs.
Top Page Image Contents