Frymaster Protector Series Oil Attendant Automatic Top-Off, Prepare the System for Use

Page 22

3.5 Oil Attendant™ Automatic Top-Off

Oil is continually topped off in the frypots from a reservoir in the cabinet. The reservoir holds a 35 pound box of oil. In a typical operation this will last approximately two days before changing.

Components of the system are annotated at the right (see Figure 1).

NOTE: The system is intended to top off the frypots, not fill them. The frypots will require manual filling upon startup and after boil out.

3.5.1 Prepare the System for Use

 

 

To prepare the system for its initial

 

 

operation, remove the cross brace (see

 

 

Figure 2). Do not replace the screws. Do

 

 

not remove cross brace before fryer is in its

 

 

final position.

Install the JIB

basket

 

 

shipped in the

accessories pack.

Follow

Figure 2

Figure 3

these instructions to prepare the cabinet for the installation of the first box of oil and subsequent boxes of oil.

3.5.2 Install the Oil Reservoir

Remove the original lid from the oil container and foil liner. Replace with the provided cap, which has connected suction hardware. Ensure the feeder tube from the cap reaches to the bottom of the oil con- tainer.

Place the oil container inside the cabinet and slide it into place (as shown on the following page). Avoid catching the suction hardware on the cabinet interior as the container is placed in the fryer.

The system is now ready for operation. As the fryer heats to preprogrammed temperatures, the system will energize and then slowly add oil to the frypot as needed, until the oil reaches an optimal level.

3.5.3Routine Oil Changes

When the oil reservoir level is low, the Oil

 

Butler®, a

yellow LED, is activated (see

 

Figure 4).

Once the reservoir is refilled

 

and/or replaced, pressing the reset button

Figure 4

above the JIB turns the LED off.

3-5

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Hour Service Hotline Protector Series GAS FryersCanada Iii Safety Information Applicability and ValidityComputer Information for the CM7 Computers European Community CE Specific InformationEquipment Description Installation, Operating, and Service PersonnelDefinitions Parts Ordering and Service Information Shipping Damage Claim ProcedureWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE General Installation Requirements Do not block the area around the base or under the fryersNational Code Requirements Caster/Leg Installation Electrical Grounding RequirementsNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures Converting to another Gas Type CE GAS Conversion InstructionsPositioning the Fryer Protector Series GAS Fryer Operating Instructions Finding Your WAY around the Protector Series GAS FryerController Operation and Programming Press the computer ON/OFF switch to the OFF position Lighting the FryerBoiling Out the Frypot Shutting the Fryer DownPrepare the System for Use Install the Oil ReservoirOil Attendant Automatic Top-Off Routine Oil ChangesBulk Oil Systems Protector Series GAS Fryers CM7 Computer Instructions CM7 General InformationBasic Operation Cooking with Multi-Product Display FR Fries Cooking with Dedicated DisplayChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast CM7 Button Description and Functions Navigation ButtonsAdding New Product Menu Items Temperature Conversion from F to CCM7 Menu Summary Tree Storing Product Menu Items in Product Buttons7378 Setup Mode ProgrammingSetup 12hrPage Page 10 CM7 Common Tasks 1650Page Sensitivity Storing Menu Items in Product Buttons Boil-Out Mode 1658Setpoint Temperature Page To E-LOG Manager Mode4321 E06 Ignition Failure Call TechnicianOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Cleaning ReassemblyDraining and Disposing of Waste Oil Inspect Fryer and Accessories for Damage Fryer Preventative Maintenance Checks and ServiceDaily Checks and Service Clean Fryer Cabinet Inside and OutMonthly Checks and Service Check Computer Magic 7 Set Point AccuracyBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Fryer Built-In Filtration SystemPage Protector Series GAS Fryers Operator Troubleshooting IntroductionTroubleshooting Fryers Computer and Heating Problems Problem Probable Causes Corrective ActionCorrective Action Probable CausesProblem Probable Causes Corrective Action Filtration ProblemsAuto Top-Off Problems Problem Probable CausesBasket Lift Problems Service Hotline

Protector Series specifications

The Frymaster Protector Series represents a significant advancement in commercial frying technology, designed to elevate both cooking efficiency and food quality while ensuring operational safety and consistency. With a focus on energy savings and ease of use, the Protector Series is tailored for establishments seeking high performance without compromising on their environmental responsibilities.

One of the standout features of the Frymaster Protector Series is its advanced temperature control technology. This series incorporates a precise digital thermostat that maintains optimal frying temperatures, allowing for consistent cooking results. Such accuracy minimizes oil degradation, extends oil life, and ultimately reduces frying costs. Coupled with the innovative oil filtration system, the Protector Series ensures that the oil remains clean, further enhancing food quality and flavor.

Another significant advancement in the Frymaster Protector Series is its improved heating elements. These elements are designed for rapid heat recovery, which means that after food is added to the fryer, the oil temperature returns to cooking levels more quickly, which is vital for high-volume frying operations. The result is reduced cooking times and increased throughput, enabling kitchens to serve more customers efficiently.

Safety is also a primary consideration in the design of the Frymaster Protector Series. It includes several built-in safety features, such as automatic shut-off controls and advanced overheating protection, ensuring that operators can work confidently without fear of accidents. Additionally, the series is equipped with easy-to-read digital displays that provide real-time monitoring of oil temperatures and cooking times, improving both safety and operational precision.

The robust construction of the Frymaster Protector Series is another notable characteristic. Built with high-quality stainless steel, these fryers are designed to withstand the rigors of busy kitchen environments. Their sleek design not only adds a modern aesthetic but also facilitates cleaning and maintenance, ensuring that kitchens remain sanitary and compliant with health regulations.

In summary, the Frymaster Protector Series is engineered for excellence in performance, safety, and efficiency. Its combination of advanced technologies, superior temperature control, and built-in safety measures makes it a valuable asset for any commercial kitchen aiming to maximize productivity while delivering exceptional food quality. Whether for a small diner or a large restaurant chain, the Frymaster Protector Series stands as a trusted solution for frying needs.
Top Page Image Contents