Frymaster Protector Series operation manual General Installation Requirements

Page 9

PROTECTOR® SERIES GAS FRYER

CHAPTER 2: INSTALLATION INSTRUCTIONS

2.1General Installation Requirements

Qualified, licensed, and/or authorized installation or service personnel, as defined in Section 1.7 of this manual, should perform all installation and service on Frymaster equipment.

Conversion of this appliance from one type of gas to another should only be performed by qualified, licensed, and/or authorized installation or service personnel as defined in Section 1.7 of this manual.

Failure to use qualified, licensed, and/or authorized installation or service personnel (as de- fined in Section 1.7 of this manual) to install, convert to another gas type or otherwise service this equipment will void the Frymaster warranty and may result in damage to the equipment or injury to personnel.

Where conflicts exist between instructions and information in this manual and local or na- tional codes or regulations, installation and operation shall comply with the codes or regula- tions in force in the country in which the equipment is installed.

DANGER

Building codes prohibit a fryer with its open tank of hot oil being installed beside an open flame of any type, including those of broilers and ranges.

Upon arrival, inspect the fryer carefully for visible or concealed damage. (See Shipping Damage Claim Procedure in Chapter 1.)

DANGER

Frymaster appliances equipped with legs are for stationary installations. Appliances fitted with legs must be lifted during movement to avoid damage to the appliance and bodily injury. For movable installations, optional equipment casters must be used. Questions? Call 1-800-551-8633.

2.1.1 Clearance and Ventilation

The fryer(s) must be installed with a 6” (150 mm) clearance at both sides and back when installed adjacent to combustible construction; no clearance is required when installed adjacent to noncombustible construction. A minimum of 24” (600 mm) clearance should be provided at the front of the fryer.

WARNING

Do not block the area around the base or under the fryers.

2-1

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Protector Series GAS Fryers Hour Service HotlineCanada Iii Applicability and Validity Safety InformationEuropean Community CE Specific Information Computer Information for the CM7 ComputersInstallation, Operating, and Service Personnel Equipment DescriptionDefinitions Shipping Damage Claim Procedure Parts Ordering and Service InformationWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE Do not block the area around the base or under the fryers General Installation RequirementsNational Code Requirements Electrical Grounding Requirements Caster/Leg InstallationNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures CE GAS Conversion Instructions Converting to another Gas TypePositioning the Fryer Finding Your WAY around the Protector Series GAS Fryer Protector Series GAS Fryer Operating InstructionsController Operation and Programming Lighting the Fryer Press the computer ON/OFF switch to the OFF positionShutting the Fryer Down Boiling Out the FrypotOil Attendant Automatic Top-Off Install the Oil ReservoirPrepare the System for Use Routine Oil ChangesBulk Oil Systems CM7 General Information Protector Series GAS Fryers CM7 Computer InstructionsBasic Operation Cooking with Multi-Product Display Cooking with Dedicated Display FR FriesChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast Navigation Buttons CM7 Button Description and FunctionsCM7 Menu Summary Tree Temperature Conversion from F to CAdding New Product Menu Items Storing Product Menu Items in Product ButtonsSetup Setup Mode Programming7378 12hrPage Page 1650 10 CM7 Common TasksPage Sensitivity Storing Menu Items in Product Buttons 1658 Boil-Out ModeSetpoint Temperature Page 4321 Manager ModeTo E-LOG E06 Ignition Failure Call TechnicianOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Reassembly CleaningDraining and Disposing of Waste Oil Daily Checks and Service Fryer Preventative Maintenance Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutCheck Computer Magic 7 Set Point Accuracy Monthly Checks and ServiceBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Built-In Filtration System FryerPage Introduction Protector Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action Troubleshooting Fryers Computer and Heating ProblemsProbable Causes Corrective ActionFiltration Problems Problem Probable Causes Corrective ActionProblem Probable Causes Auto Top-Off ProblemsBasket Lift Problems Service Hotline

Protector Series specifications

The Frymaster Protector Series represents a significant advancement in commercial frying technology, designed to elevate both cooking efficiency and food quality while ensuring operational safety and consistency. With a focus on energy savings and ease of use, the Protector Series is tailored for establishments seeking high performance without compromising on their environmental responsibilities.

One of the standout features of the Frymaster Protector Series is its advanced temperature control technology. This series incorporates a precise digital thermostat that maintains optimal frying temperatures, allowing for consistent cooking results. Such accuracy minimizes oil degradation, extends oil life, and ultimately reduces frying costs. Coupled with the innovative oil filtration system, the Protector Series ensures that the oil remains clean, further enhancing food quality and flavor.

Another significant advancement in the Frymaster Protector Series is its improved heating elements. These elements are designed for rapid heat recovery, which means that after food is added to the fryer, the oil temperature returns to cooking levels more quickly, which is vital for high-volume frying operations. The result is reduced cooking times and increased throughput, enabling kitchens to serve more customers efficiently.

Safety is also a primary consideration in the design of the Frymaster Protector Series. It includes several built-in safety features, such as automatic shut-off controls and advanced overheating protection, ensuring that operators can work confidently without fear of accidents. Additionally, the series is equipped with easy-to-read digital displays that provide real-time monitoring of oil temperatures and cooking times, improving both safety and operational precision.

The robust construction of the Frymaster Protector Series is another notable characteristic. Built with high-quality stainless steel, these fryers are designed to withstand the rigors of busy kitchen environments. Their sleek design not only adds a modern aesthetic but also facilitates cleaning and maintenance, ensuring that kitchens remain sanitary and compliant with health regulations.

In summary, the Frymaster Protector Series is engineered for excellence in performance, safety, and efficiency. Its combination of advanced technologies, superior temperature control, and built-in safety measures makes it a valuable asset for any commercial kitchen aiming to maximize productivity while delivering exceptional food quality. Whether for a small diner or a large restaurant chain, the Frymaster Protector Series stands as a trusted solution for frying needs.
Top Page Image Contents