6.2.4 Filtration Problems
Problem |
| Probable Causes | Corrective Action |
| ||
Fryer filters after each | Filter prompt setting incorrect. | Change the filter prompt setting. |
| |||
cook cycle. |
|
|
| |||
|
|
|
|
| ||
|
|
|
| |||
Filter menu functions | Temperature too low. | Ensure fryer is at setpoint before starting; | ||||
won’t start. | ensure the controller is ON. |
| ||||
|
|
|
| |||
Controller displays | Another function is still in process. | Wait until the previous function ends to | ||||
WAIT FOR FILTER. | start another filtration cycle. |
| ||||
|
|
| A. Verify that the power cord is fully | |||
|
|
| plugged in and the circuit breaker is | |||
| A. Power cord is not plugged in or circuit | not tripped. |
|
| ||
| B. If the motor is too hot to touch for | |||||
Filter pump won't start |
| breaker is tripped. | more than a few | seconds, | the | |
B. | Pump motor has overheated causing | thermal overload | switch | has | ||
or pump stops during | ||||||
| the thermal overload switch to trip. | probably tripped. Allow the motor | ||||
filtering. |
| |||||
C. | Blockage in filter pump. | to cool at least 45 minutes then press | ||||
| ||||||
|
|
| the Pump Reset Switch. (See page 5- | |||
|
|
| 4) |
|
| |
|
|
| C. Call your FAS for assistance. |
| ||
|
|
|
| |||
|
|
| Remove the oil from the filter pan and | |||
| Improperly installed or prepared filter pan | replace the filter paper, ensuring that | ||||
Filter Pump runs, but | the filter screen is in place under the | |||||
oil return is very slow. | components or cold oil. | paper. |
|
| ||
|
|
|
| |||
|
|
| Verify that | |||
|
|
| good condition on filter pan connection | |||
|
|
| fitting. |
|
| |
Controller displays | Drain valve open or possibility that oil is in | Press S (CONFIRM) and follow | ||||
OIL IN DRAIN | directions for FILL VAT FROM | |||||
PAN / CONFIRM | drain pan. | DRAIN PAN. |
|
| ||
|
|
|
|
| ||
6.2.5 Auto |
|
|
| |||
Problem |
| Probable Causes | Corrective Action |
| ||
Frypots top off cold. | Incorrect setpoint. | Ensure setpoint is correct. |
|
| ||
|
|
|
|
| ||
|
|
| A. Fryer temperature must be | at | ||
|
|
| setpoint. |
|
| |
|
|
| B. Ensure that the oil in the JIB is | |||
| A. Fryer temperature too low. | above 70°F (21°C). |
|
| ||
Frypots won’t top off. | C. Ensure the JIB is not out of oil and | |||||
B. Oil is too cold. | supply line is in the JIB. Replace JIB | |||||
| C. JIB out of oil | and press the S button when | ||||
| D. | Service required error exists | prompted to reset top off system. |
| ||
|
|
| If problem persists call your FAS for | |||
|
|
| assistance. |
|
| |
|
|
| D. Call your FAS for assistance. |
| ||
| A. | Filter error exists. | A. Clear filter error properly. If |
| ||
| problem persists call your FAS for | |||||
One vat doesn’t top off. | B. Service required error exists | |||||
assistance. |
|
| ||||
| C. Solenoid, pump, pin issue, RTD or | B. Call your FAS for assistance. |
| |||
|
| ATO issue. |
| |||
|
| C. Call your FAS for assistance. |
| |||
|
|
|
| |||
|
|
|
|
|
|