Frymaster FDP65 Frymaster FPD65 Series GAS Fryers Installation, Installing the Fryer

Page 14

FRYMASTER FPD65 SERIES GAS FRYERS

CHAPTER 3: INSTALLATION

3.1 Installing the Fryer

Decathlon 65 Series fryer systems are shipped in sections. The fryers are uncrated, removed from pallets and assembled together. Important aspects during assembly include aligning and connecting the drain system, oil return system, rinse-line system (where applicable), oil-return switch wiring harness and fryer cabinets. Slight modifications to connecting hardware may be required when assembling the system. The instructions below provide step-by-step instructions to assist the installer in assembly. For this procedure, the fryers are numbered from right to left as follows: Fryers #1, #2, #3, #4, #5 and #6 (where applicable).

1.Open the doors of the filtration fryer cabinet. Remove filter pan from the cabinet. Uncrate fryers and remove the pallet supports. Install ramps and slowly roll the fryer(s) off the pallets.

2.Remove door from fryers to be connected by lifting the door upward and removing the door pin from the bottom hinge. Remove slip-nuts from drain-tees on fryers being connected, lubricate O-rings with vegetable oil and install on drainpipe (Fig. 2). Use care not to damage the slip-nutO-rings when installing slip-nut on drainpipe. Insert the drainpipe into the fryer drain-tee (Fig. 3). Screw slip-nut onto the tee but do not tighten at this time. Position fryers being connected within 6 inches of each other, near the permanent installation area. Guide the drainpipe through the opposite fryer cabinet opening as the cabinets are positioned.

NOTE: When the slip nuts are tightened, the "blue" marks on each end of the drainpipe should align to the outside edge of each slip nut.

Figure 1. Remove pallet supports (arrow) before removing fryers from pallets.

Properly align the drainpipe evenly between the two drain-tees using the "blue" marks on the tube ends to prevent leaks and/or blocked drain valves.

Figure 2. Slip-nut/drainpipe detail.

Figure 3. Insert drainpipe section into fryer drain-tee before pushing fryers together (arrow). Do this as required for all cabinets being assembled.

3-1

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Hour Service Hotline FPD65 Series with Built-In FiltrationCanada Page Table of Contents Filtration Operation After Purchase Service InformationFrymaster FPD65 Series GAS Fryers Introduction Ordering PartsSafety Information Service Personnel DefinitionsFrymaster FPD65 Series GAS Fryers Important Information Receiving and Unpacking EquipmentGeneral Product DescriptionRating Plate Pre-InstallationPrinciples of Operation Installation Standards Equipment Installed at High Altitudes Air Supply and VentilationFrymaster FPD65 Series GAS Fryers Installation Installing the FryerFrymaster FPD65 Series GAS Fryers Installation Never Allow Water or Boilout Solution Into Filter System Gas Connections National Code RequirementsRecommended Gas Supply Line Sizes Gas Connections Adjustments/Adaptation To Different Gases Specifications Adjustments to Different Gas TypesGas Conversion Procedures Electrical ConnectionsFrymaster FPD65 Series GAS Fryers Fryer Operations Initial Start-upPilot Lighting Procedures, Electronic Ignition Systems Frymaster FPD65 Series GAS Fryers Fryer OperationsBoil-Out Procedure Boil-Out Procedure Final Preparation Assembling the Filter Frymaster FPD65 Series GAS Fryers Filtration OperationFiltration Preparation Frymaster FPD65 Series GAS Fryers Filtration Operation Place the crumb tray in filter pan Filter Leaf Disassembly/Assembly Cleaning the Filter Leaf Assembly Daily Filtration OperationFiltering Tools Operating the Filter Filter Operation Frymaster FPD65 Series GAS Fryers Filtration Operation Frypot Frymaster FPD65 Series GAS Fryers Filtration Operation Frymaster FPD65 Series GAS Fryers Preventative Maintenance WeeklyFrymaster FPD65 Series GAS Fryers Preventative Maintenance Periodic/ AnnualFrymaster FPD65 Series GAS Fryers Preventative Maintenance Frymaster FPD65 Series GAS Fryers Troubleshooting Pilot Burner MalfunctionMain Burner Malfunctions Main Burner Malfunctions Diagram, Main HI LimitWiring Diagram FilterFrymaster FPD65 Series GAS Fryers Parts List Cabinetry and Related ComponentsFrymaster FPD65 Series GAS Fryers Parts List FPD665 Shown Doors, Topcaps and Related ComponentsFrypots, Burners and Related Components Flue Assembly, Complete Component Box Components CM4-SFilter Pan and Related Components Oil-Drain Components 823-4189 Oil-Return Components Choose From Nipple Lengths BelowSuction Tube, Oil-Return Components Oil Suction Start Fitting This page Intentionally Left Blank Service Hotline

FDP65 specifications

The Frymaster FDP65 is a state-of-the-art commercial fryer known for its reliability and efficiency in high-demand cooking environments. Designed to meet the rigorous requirements of restaurants and food service establishments, the FDP65 combines advanced technology with user-friendly features, making it a top choice among chefs and kitchen managers.

One of the key features of the Frymaster FDP65 is its patented "Fast Recovery" system. This technology ensures rapid temperature recovery after food is added, allowing for consistent frying results even during peak cooking times. The ability to maintain optimum temperatures helps improve food quality and decreases cooking times, ultimately enhancing the overall operational efficiency of the kitchen.

The FDP65 employs a durable stainless-steel construction, making it resilient and easy to clean. The fryer's smooth surfaces and rounded edges contribute to its hygienic design, which is crucial in maintaining food safety standards. Additionally, the unit is equipped with heavy-duty, solid-state controls that provide precise temperature management, further enhancing its reliability.

Another remarkable characteristic of the FDP65 is its innovative filtration system. The built-in filtration minimizes oil pollution, maximizing the lifespan of cooking oil, which leads to significant cost savings over time. The automatic filtration system regularly cleans the oil and eliminates food particulates, ensuring that every batch of fried food tastes as good as the first.

The Frymaster FDP65 features a large fry pot capacity, making it suitable for frying large volumes of food. This capability is particularly beneficial for establishments with high customer turnover and those that require fast service, such as quick-service restaurants and cafeterias. The fryer also has a robust heating element that guarantees a quick preheat, reducing waiting times for both customers and kitchen staff.

Safety is another priority in the design of the FDP65. It comes equipped with a temperature limiting device that prevents overheating, as well as a high-limit switch that offers additional protection against potential hazards. Ergonomically designed fry baskets and handles make it more convenient and safer for staff to use, further enhancing the fryer’s appeal.

In summary, the Frymaster FDP65 is an exceptional commercial fryer characterized by its advanced technology, robust construction, and user-friendly features. Its fast recovery system, automatic filtration, and safety mechanisms make it an efficient and reliable choice for any busy kitchen, ensuring that operators can serve high-quality fried foods consistently while managing costs effectively.
Top Page Image Contents